• Energy Research
• engineering and technology close
• 7. Clean energy close
• 6. Clean water close
• 2. Zero hunger close

The most severe failures in power grids are often characterized as cascading failures where an initial event triggers consequent failures all along the grid often leading to blackouts. Upon identifying a failure and its cascade potential, timely control actions should be performed by the grid operators to mitigate the effect of the cascade. These actions have to be delivered to one or more control devices, creating a dependency between the power grid and its control network. This paper examines the dependency of the operation of the power grid on the control network. Different from literature studies on failure control, our dependency model captures the impact of networking parameters. We formulate an algorithmic model that describes the impact of this dependency on cascade control. Based on this model, we propose an efficient cascade control algorithm using load shedding with consideration of delays in the communication network for power grids. Finally, we evaluate the impact of the power-communication network dependency with uncontrolled grids, ideal/simple control grids and our proposed control scheme. The results demonstrate that the proposed algorithm can significantly reduce the failure of power lines while sustaining larger power demand for users.

This study focuses on formulating the most sustainable concrete by incorporating recycled concrete aggregates and other products retrieved from construction and demolition (C&D) activities. Both recycled coarse aggregates (RCA) and recycled fine aggregates (RFA) are firstly used to fully replace the natural coarse and fine aggregates in the concrete mix design. Later, the cement rich ultrafine particles, recycled glass powder and mineral fibres recovered from construction and demolition wastes (CDW) are further incorporated at a smaller rate either as cement substituent or as supplementary additives. Remarkable properties are noticed when the RCA (4–12 mm) and RFA (0.25–4 mm) are fully used to replace the natural aggregates in a new concrete mix. The addition of recycled cement rich ultrafines (RCU), Recycled glass ultrafines (RGU) and recycled mineral fibres (RMF) into recycled concrete improves the modulus of elasticity. The final concrete, which comprises more than 75% (wt.) of recycled components/materials, is believed to be the most sustainable and green concrete mix. Mechanical properties and durability of this concrete have been studied and found to be within acceptable limits, indicating the potential of recycled aggregates and other CDW components in shaping sustainable and circular construction practices. The authors wish to acknowledge the financial support from EU Horizon 2020 Project VEEP ‘‘Cost-Effective Recycling of C&DW in High Added Value Energy Efficient Prefabricated Concrete Compo-nents for Massive Retrofitting of our Built Environment” (No.723582).

Four species of wood: two softwoods (Douglas-fir and pine) and two hardwoods (aspen and hybrid poplar) are investigated for their size reduction energy consumption and ground particles size distributions. Lignin content, ash content, and density of wood is measured. Specific grinding energy was 155.9, 226.1, 209.1, and 276.3 kJ/kg for Douglas-fir, pine, aspen, and hybrid poplar, respectively. The analysis of variance shows that lignin content (ranged from 26 to 36.7 %wt based on oven-dry, extractive-free wood) and ash content (ranged from 0.36 to 0.55 % wt dry basis) are significant factors on effective energy consumption of grinding.

AbstractIn this paper a complete vehicle system simulation tool chain which applies a Multi Objective Optimization (MOO) methodology for designing the Electric Powertrain (ePT) of Battery Electric Vehicles (BEV) is presented. Optimization scope includes all relevant electric powertrain components from battery, inverter, electric machine to gear box. In addition to cost, vehicle dynamics, energy consumption and range are further optimization targets. For an overall minimal system cost design a multiplicity of interactions between all powertrain components has to be taken into account. High system complexity prevents an expert to consider all relevant correlations without the support of numeric simulation tools. The presented simulation tool chain enables fast identification of the best cost/benefit trade off regarding system cost while considering all defined system performance requirements. The approach enables experts to find unconventional solutions which would have been overlooked applying a classical straight forward approach and, thus, helps to sharpen the expert's knowledge in cause-effect relationships on the system level. Typical use cases are given and illustrated by several practical examples.

The use of superconducting magnetic energy storage (SMES) has been widely reported in the literature to mitigate various load frequency control (LFC) issues in a multi-area power system. Most of these are thyristor based SMES, employing proportional type controllers. In this paper, a supervisory adaptive model predictive control scheme (AMPC) is proposed for a voltage source converter based relatively small rating SMES for LFC application. The reference power command for the SMES is derived from the AMPC in such a manner that it effectively handles the operational constraints of the SMES system. A representative first-order system emulating the inner loop dynamics of the SMES chopper system, is tuned offline via genetic algorithm (GA) and is used to derive dynamic constraints for the cost function in AMPC. The effectiveness of the scheme is demonstrated through simulations.

AbstractHere, we present the results of evaluation of solar energy potential and photovoltaic (PV) module performance from actual data measured over a period of more than 2 years in the Gobi Desert of Mongolia. To allow estimation of solar energy potentials and durability of PV systems in the Gobi Desert area, a data acquisition system, including crystalline silicon (c‐Si), polycrystalline silicon (p‐Si) modules, and two sets of precision pyranometers, thermometers, and anemometer, was installed at Sainshand City in October 2002. This system measures 23 parameters, including solar irradiation and meteorological parameters, every 10 min. High output gain was observed due to operation at extremely low ambient temperatures and the module performance ratios (PRs) were high (>1·0) in winter. In summary, the present study showed that a PV module with a high temperature coefficient, such as crystalline silicon, is advantageous for use in the Gobi Desert area. Copyright © 2006 John Wiley & Sons, Ltd.

Experimental investigation into the effects of different pilot amounts of dimethyl ether (DME) on the performance and emission of a single-cylinder directinjection DME engine is conducted. The results show that a DME engine can operate at a wider range of speeds and loads at quasi-homogenous charge compression ignition (QHCCI) mode. The brake thermal efficiency increases while the exhaust temperature decreases. NOx emission decreases by about 30%–50% although there is a slight increase in HC and CO emissions. NOx, HC and CO emissions increase with an increase in the amount of DME pilot. QHCCI is a good way to increase thermal efficiency and decrease NOx emission.

Abstract Predicting and optimizing radiative thermal properties have been acknowledged as an efficient way to improve thermal insulation performance of fibrous materials with high porosity. Based on experimental investigation of infrared spectral of ultrafine fibrous insulations with diameters of 520–650 nm, a method of calculating radiative thermal properties was presented by combining Rosseland equation, Mie scattering theory, Beer’s law and Subtractive Kramers–Kronig (SKK) relation. To ensure the calculation correct the uniqueness analysis was performed for Poly(vinylidene fluoride) (PVDF) fibers, which indicated the valid fiber diameter was less than 1.06 μm. The calculated thermal radiative conductivities by using the method agreed well with the measured data. The effect of fiber diameter on the thermal properties of the fibrous insulations was also investigated to minimize the radiative thermal conductivity. The results indicated that the minimized radiative thermal conductivities by regulating fiber diameters could be approximately 25% smaller than those for experimental fiber diameters. The method of predicting and minimizing radiative thermal conductivities of fibrous insulations demonstrated in this paper could be of great advantage to thermal engineering applications aiming to reducing heat loss and saving energy.