• Energy Research
• Open Access close
• chemical engineering close

AbstractThis paper presents the experimental plans and designs as well as examples of predictive modeling of a pilot-scale CO2 injection experiment at the Heletz site (Israel). The overall objective of the experiment is to find optimal ways to characterize CO2 -relevant in-situ medium properties, including field-scale residual and dissolution trapping, to explore ways of characterizing heterogeneity through joint analysis of different types of data, and to detect leakage. The experiment will involve two wells, an injection well and a monitoring well. Prior to the actual CO2 injection, hydraulic, thermal and tracer tests will be carried out for standard site characterization. The actual CO2 injection experiments will include (i) a single well injection-withdrawal experiment, with the main objective to estimate in-situ residual trapping and (ii) a two-well injection-withdrawal test with injection of CO2 in a dipole mode (injection of CO2 in one well with simultaneous withdrawal of water in the monitoring well), with the objective to understand the CO2 transport in heterogeneous geology as well as the associated dissolution and residual trapping. Tracers will be introduced in both experiments to further aid in detecting the development of the phase composition during CO2 transport. Geophysical monitoring will also be implemented. By means of modeling, different experimental sequences and injection/withdrawal patterns have been analyzed, as have parameter uncertainties. The objectives have been to (i) evaluate key aspects of the experimental design, (ii) to identify key parameters affecting the fate of the CO2 and (iii) to evaluate the relationships between measurable quantities and parameters of interest.

AbstractIn geologic carbon sequestration, caprock fractures may act as leakage pathways, threatening the long term sealing ability of the formation. A flow-through experiment was performed to investigate fracture evolution of a fractured carbonate caprock during simulated leakage of CO2-acidified brine. The initial brine composition represented that of a CO2-saturated brine having previously reacted with the injection formation minerals resulting in a starting pH of 4.9. Experimental temperature and pressure conditions were 40 °C and 10 MPa, corresponding to injection at a depth of 1 km. A combination of X-ray computed tomography and scanning electron microscopy was used to observe fracture evolution and investigate the mineralogical changes that occurred along the fracture wall. After one week of brine flow, the cross-sectional fracture area increased by an average of 2.7 times that of the initial fracture. The fracture surface was not eroded uniformly, with the largest areas of aperture growth corresponding to direct contact between the acidified brine and calcite. This preferential dissolution of calcite led to a large increase in fracture surface roughness and in some instances, created a silicate mineral-rich microporous coating along the fracture wall. Results from this study suggest that the clay content of low permeability carbonate formations may be an important factor in controlling their long term integrity while in contact with acidified brine and should be considered when selecting appropriate injection sites for geologic CO2 sequestration.

Fracture conductivity decline is a concern in the Tuscaloosa Marine Shale (TMS) wells due to the high content of clay in the shale. An analytical well productivity model was developed in this study considering the pressure-dependent conductivity of hydraulic fractures. The log-log diagnostic approach was used to identify the boundary-dominated flow regime rather than the linear flow regime. Case studies of seven TMS wells indicated that the proposed model allows approximation of the field data with good accuracy. Production data analyses with the model revealed that the pressure-dependent fracture conductivity in the TMS in the Mississippi section declines following a logarithmic mode, with dimensionless coefficient χ varying between 0.116 and 0.130. The pressure-dependent decline of fracture conductivity in the transient flow period is more significant than that in the boundary-dominated flow period.

For the investigation on some hydrate dissociation behaviors at different ambient conditions, methane hydrates formed inside porous media with different saturations were dissociated by depressurizations. Plots of the instantaneous flow rate of gas as dissociation versus production pressure as well as deformation of experimental sample versus accumulative amount of released gas were drawn. These two lines slopes are, respectively, characterized as gas discharge resistance and reciprocal of the latter one as damage degree of experimental samples. The results show that these formed hydrates at higher ambient conditions, that is, temperature and pressure, and possess a higher saturation, which is beneficial to discharge gas and to keep experimental samples undamaged. And the nonuniformity of dissociation processes at different layer positions induced by depressurization is inhibited significantly, especially while combining extra heating. Hydrate saturation dominates the total volume loss of these samples under loadings. These conclusions can provide reference for the prediction in gas discharge capability and media damage degree as hydrate dissociation at different experimental and natural ambient conditions.

Swirl combustors have proven as effective flame stabilisers over a wide range of operation conditions thanks to the formation of well-known swirl coherent structures. However, employment of swirl combustors to work on lean premixed combustion modes while introducing alternative fuels such as high hydrogen blends result in many combustion instabilities. Under these conditions, flame flashback has been considered as one of the major instability problems that have the potential of causing considerable damages of the combustion systems hardware in addition to the significant increase in pollutant levels. Combustion Induced Vortex Breakdown (CIVB) is considered a very particular mode of flashback mechanism in swirling flows as this type of flashback occurs even when the fresh mixture’s velocity is higher than the flame speed, consequence of the interaction between swirl structures and swirl burner geometries. Improvements of burner geometries and manipulation of swirl flows can produce good resistance against this type of flashback. However, increase flame flashback resistance against CIVB can lead to an increase in the propensity of another flashback mechanism, Boundary Layer Flashback (BLF). Thus this paper presents an experimental and numerical approach that allows the increase in CIVB resistance by using diffusive air injection and simultaneously avoid BLF by changing the wall boundary layer characteristics using microsurface grids as a liner for the nozzle wall. Results show that using those two techniques together has promising potentials regarding wider stable operation for swirl combustors, enabling them to burn a great variety of fuel blends safely.

The present paper reports a numerical study of a spray impinging on a surface through a crossflow and is aimed at studying the fundamental aspects of the spray impingement phenomena in a three-dimensional configuration, which is relevant to practical engines. Different impinging models were used and the results are compared with measurements and predictions of other authors. The results show a general good agreement with the experiments, and reveal that the splash droplets are very important for the spray development. The performance of droplet impinging models depends strongly on the conditions of pre-impingement. Nomenclature cf = friction coefficient d = generic diameter of a droplet d32 = Sauter Mean Diameter (SMD) dV = volumetric mean diameter EK = droplet kinetic energy Eσ = droplet surface energy ED = dissipation energy H = height of wind tunnel hf =

The breakdown of the drill bit or rapid decrease of the rate of penetration during the drilling process results in a delay in the progress of drilling. Scientists and engineers are increasingly focusing on research to extend the bit life and improve the drilling rate. In our work, “in situ” drilling parameters were monitored during the drilling process with the roller cone drill bit IADC 136, diameter 155.57 mm (6 1/8"). After drilling, the bit was thoroughly examined to determine the damage and wear that occurred during drilling. The following modern and standardized investigative methods were used: an analysis of rock materials and an analysis of micro and macrostructure materials of the roller cone bit. Analyses were carried out using optical and electron microscopy, a simultaneous thermal analysis of materials of drill bit, analysis of the chemical composition of materials of drill bit, and a determination of the geomechanical parameters of rock materials. The resulting wear, local bursts, and cracks were quantitatively and qualitatively defined and linked to the drilling regime and the rock material. The results of our investigation of the material of the roller cone bit can serve as a good base for the development of new steel alloys, which can resist higher temperatures and enable effective drilling, without structural changes of steel material.

Environmental concern for our planet has changed significantly over time due to climate change, caused by an increasing population and the subsequent demand for electricity, and thus increased power generation. Considering that natural gas is regarded as a promising fuel for such a purpose, the need to integrate carbon capture technologies in such plants is becoming a necessity, if gas power plants are to be aligned with the reduction of CO2 in the atmosphere, through understanding the capturing efficacy of different absorbents under different operating conditions. Therefore, this study provided for the first time the comparison of available absorbents in relation to amine solvents (MEA, DEA, and DEA) CO2 removal efficiency, cost, and recirculation rate to achieve Climate change action through caron capture without causing absorbent disintegration. The study analyzed Flue under different amine-based solvent solutions (monoethanolamine (MEA), diethanolamine (DEA), and methyldiethanolamine (MDEA)), in order to compare their potential for CO2 reduction under different operating conditions and costs. This was simulated using ProMax 5.0 software modeled as a simple absorber tower to absorb CO2 from flue gas. Furthermore, MEA, DEA, and MDEA adsorbents were used with a temperature of 38 °C and their concentration varied from 10 to 15%. Circulation rates of 200–300 m3/h were used for each concentration and solvent. The findings deduced that MEA is a promising solvent compared to DEA and MDEA in terms of the highest CO2 captured; however, it is limited at the top outlet for clean flue gas, which contained 3.6295% of CO2 and less than half a percent of DEA and MDEA, but this can be addressed either by increasing the concentration to 15% or increasing the MEA circulation rate to 300 m3/h.