• Energy Research
• medical engineering close

Most investigations of the material properties of bone have been concerned with the measurement of absolute values for various mechanical parameters. It can be necessary, however, to produce test samples with similar mechanical properties in order to assess the effect on these properties of particular treatments. Absolute values for these properties may not be as important as any changes observed. We describe here a new method whereby many bone test samples with very similar mechanical properties can be produced. If the femoral shaft at the diaphysis is cut in transverse section, it is possible to produce many similar shaped rings of bone. We compared the material properties of 48 ring samples with 65 beam specimens. Both were tested in three-point bending. Global estimates of coefficient of variation (CV) for each parameter were used to assess similarity within each group. All the rings had very similar ash weights (1.98%), thicknesses (1.97%), and diameters (< 0.01%). Values of load/deflection of the rings were more similar than the values of Young's modulus (E) for the beams (7.06 versus 9.9%), and the maximum loads sustainable by the rings were more similar than the bending strengths of the beams (5.7 versus 13.6%). The energy absorbed by the ring samples were more consistent than the beams (14.31 versus 34.41%). We suggest that there is improved similarity in mechanical characteristics within groups of samples produced in this manner than with more conventional sample configurations.

Most investigations of the material properties of bone have been concerned with the measurement of absolute values for various mechanical parameters. It can be necessary, however, to produce test samples with similar mechanical properties in order to assess the effect on these properties of particular treatments. Absolute values for these properties may not be as important as any changes observed. We describe here a new method whereby many bone test samples with very similar mechanical properties can be produced. If the femoral shaft at the diaphysis is cut in transverse section, it is possible to produce many similar shaped rings of bone. We compared the material properties of 48 ring samples with 65 beam specimens. Both were tested in three-point bending. Global estimates of coefficient of variation (CV) for each parameter were used to assess similarity within each group. All the rings had very similar ash weights (1.98%), thicknesses (1.97%), and diameters (< 0.01%). Values of load/deflection of the rings were more similar than the values of Young's modulus (E) for the beams (7.06 versus 9.9%), and the maximum loads sustainable by the rings were more similar than the bending strengths of the beams (5.7 versus 13.6%). The energy absorbed by the ring samples were more consistent than the beams (14.31 versus 34.41%). We suggest that there is improved similarity in mechanical characteristics within groups of samples produced in this manner than with more conventional sample configurations.

An alcohol-free tissue conditioner based on a n-butyl methacrylate/i-butyl methacrylate copolymer has recently been developed. The purpose of the present study was to compare some key properties of the new tissue conditioner with those of poly(ethyl methacrylate)-based conventional materials containing ethyl alcohol. The effect of a coating, which consisted of poly(ethyl methacrylate) and methyl methacrylate, was also evaluated.The new alcohol-free tissue conditioner (Fictioner) and three tissue conditioners containing ethyl alcohol (FITT, Hydro-Cast, SR-Ivoseal) were evaluated. The coated alcohol-free material was also used. Gelation characteristics, dynamic viscoelastic properties and compatibility with dental stones were measured using a displacement rheometer, dynamic viscoelastometer and profilometer, respectively. In addition, weight changes during immersion in water were determined.The working time and gelation time of the alcohol-free tissue conditioner were similar to those of the conventional materials. This alcohol-free material had significantly lower shear storage modulus and shear loss modulus, and higher loss tangent (P<0.05) than FITT and SR-Ivoseal at 0.01 and 1 Hz. The alcohol-free material maintained its inherent viscoelastic properties and exhibited only a slight change in weight during 14 days of water immersion when compared to the conventional materials. The application of the coating significantly reduced the loss of the initial viscoelastic properties and surface quality during the test periods.The coated alcohol-free tissue conditioner would be superior to the conventional materials containing ethyl alcohol in view of viscoelastic properties after gelation, compatibility with dental stones and durability.

An alcohol-free tissue conditioner based on a n-butyl methacrylate/i-butyl methacrylate copolymer has recently been developed. The purpose of the present study was to compare some key properties of the new tissue conditioner with those of poly(ethyl methacrylate)-based conventional materials containing ethyl alcohol. The effect of a coating, which consisted of poly(ethyl methacrylate) and methyl methacrylate, was also evaluated.The new alcohol-free tissue conditioner (Fictioner) and three tissue conditioners containing ethyl alcohol (FITT, Hydro-Cast, SR-Ivoseal) were evaluated. The coated alcohol-free material was also used. Gelation characteristics, dynamic viscoelastic properties and compatibility with dental stones were measured using a displacement rheometer, dynamic viscoelastometer and profilometer, respectively. In addition, weight changes during immersion in water were determined.The working time and gelation time of the alcohol-free tissue conditioner were similar to those of the conventional materials. This alcohol-free material had significantly lower shear storage modulus and shear loss modulus, and higher loss tangent (P<0.05) than FITT and SR-Ivoseal at 0.01 and 1 Hz. The alcohol-free material maintained its inherent viscoelastic properties and exhibited only a slight change in weight during 14 days of water immersion when compared to the conventional materials. The application of the coating significantly reduced the loss of the initial viscoelastic properties and surface quality during the test periods.The coated alcohol-free tissue conditioner would be superior to the conventional materials containing ethyl alcohol in view of viscoelastic properties after gelation, compatibility with dental stones and durability.

In urology, single cases of lethal pulmonary embolism following extracorporeal shock wave application to renal concrements have been reported. Therefore, lungs of rabbits were histopathologically investigated following extracorporeal shock wave application to the femur.In 8 mature Chinchilla-Bastard rabbits, shock wave application to one distal femur was performed with energy flux density of 0.9 mJ/mm2. In another 6 rabbits, sham-treatment (0 mJ/mm2) to one distal femur was performed. 6 weeks later, the animals were sacrificed and their lungs were blindly investigated by an independent pathologist.In 7 out of the 8 treated animals (0.9 mJ/mm2) but in none of the sham-treated controls, patchy discolorations of the surface of the lung were observed. Furthermore, in 6 out of the 8 treated animals but in none of the sham-treated controls, bony fragments with signs of resorption were observed in lung vessels.Application of extracorporeal shock waves with energy flux densities higher than 0.9 mJ/mm2 has been recommended in the literature for the treatment of aseptic non-unions. In this procedure, the possibility of the occurrence of bone fragments in the lung with the potential risk of pulmonary embolism should be regarded.

In urology, single cases of lethal pulmonary embolism following extracorporeal shock wave application to renal concrements have been reported. Therefore, lungs of rabbits were histopathologically investigated following extracorporeal shock wave application to the femur.In 8 mature Chinchilla-Bastard rabbits, shock wave application to one distal femur was performed with energy flux density of 0.9 mJ/mm2. In another 6 rabbits, sham-treatment (0 mJ/mm2) to one distal femur was performed. 6 weeks later, the animals were sacrificed and their lungs were blindly investigated by an independent pathologist.In 7 out of the 8 treated animals (0.9 mJ/mm2) but in none of the sham-treated controls, patchy discolorations of the surface of the lung were observed. Furthermore, in 6 out of the 8 treated animals but in none of the sham-treated controls, bony fragments with signs of resorption were observed in lung vessels.Application of extracorporeal shock waves with energy flux densities higher than 0.9 mJ/mm2 has been recommended in the literature for the treatment of aseptic non-unions. In this procedure, the possibility of the occurrence of bone fragments in the lung with the potential risk of pulmonary embolism should be regarded.

An implantable power generation system driven by muscle contractions for supplying power to active implantable medical devices, such as pacemakers and neurostimulators, is proposed. In this system, a muscle is intentionally contracted by an electrical stimulation in accordance with the demands of the active implantable medical device for electrical power. The proposed system, which comprises a small electromagnetic induction generator, electrodes with an electrical circuit for stimulation and a transmission device to convert the linear motion of the muscle contractions into rotational motion for the magneto rotor, generates electrical energy. In an ex vivo demonstration using the gastrocnemius muscle of a toad, which was 28 mm in length and weighed 1.3 g, the electrical energy generated by the prototype exceeded the energy consumed for electrical stimulation, with the net power being 111 µW. It was demonstrated that the proposed implantable power generation system has the potential to replace implantable batteries for active implantable medical devices.

An implantable power generation system driven by muscle contractions for supplying power to active implantable medical devices, such as pacemakers and neurostimulators, is proposed. In this system, a muscle is intentionally contracted by an electrical stimulation in accordance with the demands of the active implantable medical device for electrical power. The proposed system, which comprises a small electromagnetic induction generator, electrodes with an electrical circuit for stimulation and a transmission device to convert the linear motion of the muscle contractions into rotational motion for the magneto rotor, generates electrical energy. In an ex vivo demonstration using the gastrocnemius muscle of a toad, which was 28 mm in length and weighed 1.3 g, the electrical energy generated by the prototype exceeded the energy consumed for electrical stimulation, with the net power being 111 µW. It was demonstrated that the proposed implantable power generation system has the potential to replace implantable batteries for active implantable medical devices.