• Energy Research
• other engineering and technologies close
• 7. Clean energy close

This study focuses on formulating the most sustainable concrete by incorporating recycled concrete aggregates and other products retrieved from construction and demolition (C&D) activities. Both recycled coarse aggregates (RCA) and recycled fine aggregates (RFA) are firstly used to fully replace the natural coarse and fine aggregates in the concrete mix design. Later, the cement rich ultrafine particles, recycled glass powder and mineral fibres recovered from construction and demolition wastes (CDW) are further incorporated at a smaller rate either as cement substituent or as supplementary additives. Remarkable properties are noticed when the RCA (4–12 mm) and RFA (0.25–4 mm) are fully used to replace the natural aggregates in a new concrete mix. The addition of recycled cement rich ultrafines (RCU), Recycled glass ultrafines (RGU) and recycled mineral fibres (RMF) into recycled concrete improves the modulus of elasticity. The final concrete, which comprises more than 75% (wt.) of recycled components/materials, is believed to be the most sustainable and green concrete mix. Mechanical properties and durability of this concrete have been studied and found to be within acceptable limits, indicating the potential of recycled aggregates and other CDW components in shaping sustainable and circular construction practices. The authors wish to acknowledge the financial support from EU Horizon 2020 Project VEEP ‘‘Cost-Effective Recycling of C&DW in High Added Value Energy Efficient Prefabricated Concrete Compo-nents for Massive Retrofitting of our Built Environment” (No.723582).

Four species of wood: two softwoods (Douglas-fir and pine) and two hardwoods (aspen and hybrid poplar) are investigated for their size reduction energy consumption and ground particles size distributions. Lignin content, ash content, and density of wood is measured. Specific grinding energy was 155.9, 226.1, 209.1, and 276.3 kJ/kg for Douglas-fir, pine, aspen, and hybrid poplar, respectively. The analysis of variance shows that lignin content (ranged from 26 to 36.7 %wt based on oven-dry, extractive-free wood) and ash content (ranged from 0.36 to 0.55 % wt dry basis) are significant factors on effective energy consumption of grinding.

AbstractIn this paper a complete vehicle system simulation tool chain which applies a Multi Objective Optimization (MOO) methodology for designing the Electric Powertrain (ePT) of Battery Electric Vehicles (BEV) is presented. Optimization scope includes all relevant electric powertrain components from battery, inverter, electric machine to gear box. In addition to cost, vehicle dynamics, energy consumption and range are further optimization targets. For an overall minimal system cost design a multiplicity of interactions between all powertrain components has to be taken into account. High system complexity prevents an expert to consider all relevant correlations without the support of numeric simulation tools. The presented simulation tool chain enables fast identification of the best cost/benefit trade off regarding system cost while considering all defined system performance requirements. The approach enables experts to find unconventional solutions which would have been overlooked applying a classical straight forward approach and, thus, helps to sharpen the expert's knowledge in cause-effect relationships on the system level. Typical use cases are given and illustrated by several practical examples.

The use of superconducting magnetic energy storage (SMES) has been widely reported in the literature to mitigate various load frequency control (LFC) issues in a multi-area power system. Most of these are thyristor based SMES, employing proportional type controllers. In this paper, a supervisory adaptive model predictive control scheme (AMPC) is proposed for a voltage source converter based relatively small rating SMES for LFC application. The reference power command for the SMES is derived from the AMPC in such a manner that it effectively handles the operational constraints of the SMES system. A representative first-order system emulating the inner loop dynamics of the SMES chopper system, is tuned offline via genetic algorithm (GA) and is used to derive dynamic constraints for the cost function in AMPC. The effectiveness of the scheme is demonstrated through simulations.

Experimental investigation into the effects of different pilot amounts of dimethyl ether (DME) on the performance and emission of a single-cylinder directinjection DME engine is conducted. The results show that a DME engine can operate at a wider range of speeds and loads at quasi-homogenous charge compression ignition (QHCCI) mode. The brake thermal efficiency increases while the exhaust temperature decreases. NOx emission decreases by about 30%–50% although there is a slight increase in HC and CO emissions. NOx, HC and CO emissions increase with an increase in the amount of DME pilot. QHCCI is a good way to increase thermal efficiency and decrease NOx emission.

Abstract Predicting and optimizing radiative thermal properties have been acknowledged as an efficient way to improve thermal insulation performance of fibrous materials with high porosity. Based on experimental investigation of infrared spectral of ultrafine fibrous insulations with diameters of 520–650 nm, a method of calculating radiative thermal properties was presented by combining Rosseland equation, Mie scattering theory, Beer’s law and Subtractive Kramers–Kronig (SKK) relation. To ensure the calculation correct the uniqueness analysis was performed for Poly(vinylidene fluoride) (PVDF) fibers, which indicated the valid fiber diameter was less than 1.06 μm. The calculated thermal radiative conductivities by using the method agreed well with the measured data. The effect of fiber diameter on the thermal properties of the fibrous insulations was also investigated to minimize the radiative thermal conductivity. The results indicated that the minimized radiative thermal conductivities by regulating fiber diameters could be approximately 25% smaller than those for experimental fiber diameters. The method of predicting and minimizing radiative thermal conductivities of fibrous insulations demonstrated in this paper could be of great advantage to thermal engineering applications aiming to reducing heat loss and saving energy.

Reactive power consumption of the modern power system is a very important problem that to solve well. Due to the line commutated current source converter-based (LCC) HVDC system is a multivariable and strong coupling nonlinear system, it is difficult to model reactive power consumption of receiving end of LCC-HVDC by traditional analysis method. This paper proposes the reactive power consumption model of receiving end of LCC-HVDC on account of the radial basis function (RBF) neural network. The model with the turn-off angle for input, with reactive power loss on the inverter side of LCC-HVDC for output, using 500kV, 1000MW LCC-HVDC system PSCAD simulation test data training RBF neural network and testing network generalization ability. The results indicate that the reactive power loss model on account of the RBF neural network has much faster convergence speed and higher convergence precision.

Abstract Transient thermal behaviors of ultra-supercritical steam turbine control valves during the cold start warm-up process of steam turbine systems were comprehensively studied using conjugate heat transfer (CHT) simulation. The geometrical configurations and boundary conditions used in simulation were identical to the field setup in a thermal power plant. The simulated temperature variations were first validated using measurements by the flush-mounted thermocouples inside the solid valve bodies. The CHT simulation implementing the shear stress transport (SST) turbulence model demonstrated good agreement with the field data, and the overall numerical errors were below 10%; however, the numerical errors of the simulation, which used empirical heat transfer coefficients at the fluid–solid interfaces, reached 40%. The determined temperature differences between the cold valve bodies with the hot steam flow decreased significantly. Specifically, the temperature differences along the inner wall surfaces of the valve bodies decreased to less than 50 °C. Further investigation of the transient heat flux distributions and Nusselt number distributions confirmed that the unsteady flow behaviors, such as the alternating oscillations of the annular wall-attached jet, the central reverse flow and the intermediate shear layer instabilities, enhanced the fluid–solid heat convection process and thus contributed to the warming up of the solid valve bodies.

Abstract This study sought to quantify and characterize cassava waste as fuel. The wastes from three cultivars were collected to study and were divided into three distinct parts of the cassava plant: seed stem, thick stalks, and thin stalks. Physical and chemical analyzes were carried out to determine the elemental composition of the waste: volatile matter; fixed carbon; ash; moisture; lignin; cellulose; hemicellulose; ash composition and higher heating value were determined. We conducted a thermogravimetric analysis in oxidizing and inert atmospheres to study the behavior of the waste as fuel. The root productivity obtained ranged from 7.7 to 13.0 t ha−1 yr−1 on a dry basis (db), and the ratio between waste and roots varied from 0.36 to 0.91. The physical and chemical properties of cassava waste are analogous to those of woody biomass regarding the elemental composition, the higher heating value, and thermogravimetric analysis. Ash content varied from 2.5% to 3.5%, reaching around 6.0% in samples unwashed. Approximately 60% of the ashes are alkali oxides, especially P2O5, K2O, and CaO, which have low melting points. The alkali index calculated suggests that there is a strong tendency that the combustion process leads to ash fouling and the formation of ash deposits.