• Energy Research
• 2016-2025close
• Restricted close
• other engineering and technologies close

Ammonia production through more efficient technologies can be achieved using exergy analysis. Ammonia production is one of the most important but also one of most energy consuming processes in the chemical industry. Based on a panel of solutions previously developed, this study helps to identify potential areas of improvement using an exergy analysis that covers all aspects of conventional ammonia synthesis and separation. The total internal and external exergy losses are calculated as 3,152 and 6,364 kJ/kg, respectively. The process is then divided into five main functional blocks based on their exergy losses. The reforming block contains the largest exergy loss (3,098 kJ/kg) and thus the largest potential for improvement including preheating cold feed through an economizer, developing technology towards isobaric mixing, and pressure drop reduction in the secondary reformer as the main contributors to the irreversibility (1,302 kJ/kg) in this block. The second largest exergy loss resides in the ammonia synthesis block (3,075 kJ/kg) where solutions such as reduced temperature rise across the compressor, proper compressor isolation, reducing undesired components such as argon in the reactor feed, and using lower temperatures for reactor outlet streams, are proposed to decrease the exergy losses. Throttling process in the syngas separator is the key contributing mechanism for the irreversibility (1,635 kJ/kg exergy losses) in the gas upgrading block. The exergy losses in the residual ammonia removal block (833 kJ/kg exergy losses) are mainly due to the stripper and the absorber column where a modified column design might be helpful. The highest exergy loss in the preheating block belongs to the compressors (518 kJ/kg exergy losses) where a lower inlet temperature and better system isolation could help to reduce losses.

Diesel engine exhausts from a common rail 3.0 L F1C diesel engine were analyzed at two different load conditions of the WLTC testing cycle downstream of both the diesel particulate filter (DPF) and selective catalytic reactor (SCR) to verify their effect on the characteristics of carbon particulate matter. An array of chemical, physical and spectroscopic techniques (gas chromatography coupled with mass spectrometry (GC-MS), mobility analyzer, UV-Visible absorption and fluorescence spectroscopy) was applied for characterizing polycyclic aromatic hydrocarbons (PAH), heavy aromatic compounds and soot, constituting the particulate matter (PM) sampled from the exhaust. The engine was operated in half load (HL) (188 Nm, representing the more common condition for engine in urban traffic) and full load (FL) (452 Nm, representing the best performance of the engine operation) conditions, at the same engine speed (2000 rpm). Soot formation was enhanced in HL condition, with respect to FL, but, just because of the much lower soot amount, the after-treatment systems in this last condition resulted to be less efficient in the soot abatement. Indeed, the abatement through DPF was about 40% lower in the FL condition with respect to HL condition, and any significant further concentration decrease was found after SCR, in both conditions. By contrast, PAH concentration after DPF abatement was found to be higher in the HL with respect to FL condition. A further PAH concentration decrease of about 30% was found after the SCR in the HL condition whereas in FL the reduction was only about 5-6%. Also the heavy aromatic compounds having molecular weight above the GC-MS detection limit (300 u), were mitigated by SCR. Therefore, SCR did not cause a further soot reduction, whereas it was effective in largely reducing PAH and heavy aromatics emissions, especially in the lower temperature condition featuring the half-load condition, when combustion efficiency is worse. Moreover, SCR system reduced the emission of small particles probably due to an enhanced agglomeration of particles, with beneficial effect on the harmfulness to human health.

It is now environmentally desirable and legally mandatory to add renewable fuels such as ethanol or ethyl tert-butyl ether to gasoline. However, biofuels affect, among other properties, the distillation curve of gasoline, which is subject to strict regulations. This work presents a simple mathematical model capable of accurately predicting the influence that the addition of these oxygenates has on the distillation curve. In order to address this issue, it is essential to find a simple mathematical correlation between the boiling temperatures of the hydrocarbons present in gasoline and the properties (boiling temperature and volume or molar concentration of ethanol) of the corresponding azeotropic mixtures formed with ethanol. Power functions have been assumed to model the temperature composition diagrams of the vapour-liquid equilibrium. Experimental data previously published by these and other authors have been used to fit and validate the model. The results provided by the mathematical model can be of great interest to understand the process of fuel evaporation in spark-ignition engines or the adjustment of distillation cuts in refineries, in order to comply with the regulations, in terms of the distillation curve, after adding ethanol or ethyl tert-butyl ether.

The present paper exhibits a real time assessment of a robust Energy Management Strategy (EMS) for battery-super capacitor (SC) Hybrid Energy Storage System (HESS). The proposed algorithm, dedicated to an electric vehicular application, is based on a self-gain scheduled controller, which guarantees the H∞ performance for a class of linear parameter varying (LPV) systems. Assuming that the duty cycle of the involved DC-DC converters are considered as the variable parameters, that can be captured in real time, and forwarded to the controller to ensure both; the performance and robustness of the closed-loop system. The subsequent controller is therefore time-varying and it is automatically scheduled according to each parameter variation. This algorithm has been validated through experimental results provided by a tailor-made test bench including both the HESS and the vehicle traction emulation system. The experimental results demonstrate the overall stability of the system, where the proposed LPV supervisor successfully accomplishes a power frequency splitting in an adequate way, respecting the dynamic of the sources. The proposed solution provides significant performances for different speed levels.

Ethylene oxide production process is one of the highest energy consumers in chemical industry, and therefore even a slight improvement in its overall efficiency can have a significant impact on the sustainability of the process. Efficiency improvement can be carried out using the exergy-aided pinch analysis outlined in this paper. The overall exergy loss distribution in different unit operations of an ethylene oxide process was first evaluated and mapped out in the form of “visualized exergetic process flowsheet”. An initial analysis of the four main functional blocks of the process showed that the exothermic reaction block contained the largest exergy loss (6043 and 428 kJ/kg of internal and external losses, respectively) which can be reduced by isothermal mixing, as well as increasing reaction temperature and reduction in pressure drop. The absorption block was also estimated to have the second highest contribution with total exergy losses of 3640 kJ/kg which were mainly due to the cooling column. These losses were then recommended to be reduced by improvements in the concentration and temperature gradients along the tower. Following the block-wise analysis, exergy analysis was then carried out for individual unit operations in each block to pinpoint the main sources of thermal exergetic inefficiency. Thermal solutions to reduce losses were also proposed in accordance with the identified sources of inefficiency, leading to a comprehensive list of cold and hot process streams that could be introduced to reduce losses. Finally, pinch analysis was brought into action to estimate the minimum energy requirements, to select utilities, and to design heat exchanger network. Thus, the methodology used in this work took advantage of both exergy and pinch analyses. The combined thermal-exergy-based pinch approach helped to set energy targets so that all the thermal possible solutions supported by exergy analysis were considered, preventing exclusion of any hot or cold process stream with high potential for heat integration during pinch analysis. Results indicated that the minimum cold utility requirement could be reduced from 601.64 MW (obtained via conventional pinch analysis) to 577.82 MW through screening of streams by the combined methodology.

This paper proposes a linear programming problem to find the optimal planning and operation of aggregated distributed energy resources (DER), managed by an aggregator that participates in the day-ahead wholesale electricity market as a price-maker agent. The proposed model analyzes the impact of the size of the aggregated resources and gives the optimal planning and management of DER systems, and the corresponding energy transactions in the wholesale day-ahead market. The results suggest that when the aggregated resources are large enough, DER systems can achieve up to 32% extra economic benefits depending on the market share, compared with a business-as-usual approach (not implementing DER systems). info:eu-repo/semantics/draft

This paper aims to correlate the in-cylinder soot formation and the exhaust particle emissions for different methods of gasoline/ethanol fueling in spark ignition engine. In particular, the engine was fueled with gasoline and ethanol separately and not, in this latter case both blended (E30) and dual fueled (EDF). For E30 the bend was direct injected and for EDF, the ethanol was injected in the combustion chamber and the gasoline into the intake duct. For both the injection configurations, the same percentage of ethanol in gasoline was supplied: 30%v/v. The measurements were carried out at 2000 and 4000 rpm, under full load, and stoichiometric condition, in small single cylinder optical engine. 2D-digital imaging was performed to follow the combustion process with a high spatial and temporal resolution through a full-bore optical piston. The two-color pyrometry was applied for the analysis of the in cylinder soot formation in the combustion chamber. Particle mass concentration was evaluated at the exhaust by means of a smoke meter. The particle size distribution function was measured in the range from 5.6 to 560 nm by an Engine Exhaust Particle Sizer (EEPS). It was observed that the use of ethanol allows the reduction of soot formation and particles emission in DI configuration. However, for E30 the in-cylinder soot formation and emissions are larger than EDF. This result is mainly due to the different contribution of gasoline. Optical analysis shows that in E30 the direct injected gasoline causes wide diffusive flames where soot formation is promoted; whereas for EDF the better evaporation and mixing of gasoline, typical of PFI configuration, results in few, small, and localized diffusive flames producing smaller particle emissions.

ON 16 NOVEMBER 2000, the final report of the World Commission on Dams (WCD) was launched in London, in the presence of South Africa’s former president Nelson Mandela. This represented a remarkable milestone in the history of dam policy and politics. During its two-year existence, WCD had conducted the most extensive review of research and evidence regarding the planning, impacts, and management of large dams. It had engaged with numerous stakeholders around the globe. It also made comprehensive recommendations about how to improve dam planning and management.

In the last years, even more attention was paid to the alternative fuels that allow both reducing the fossil fuel consumption and the pollutant emissions. Gaseous fuels like methane and hydrogen are the most interesting in terms of engine application. This paper reports a comparison between methane and different methane/hydrogen mixtures in a single-cylinder Port Fuel/Direct Injection spark ignition (PFI/DI SI) engine operating under steady state conditions. It is representative of the gasoline engine for automotive application. Engine performance and exhaust emissions were evaluated. Moreover, 2D-digital cycle resolved imaging was performed with high spatial and temporal resolution in the combustion chamber. In particular, it allows characterizing the combustion by means of the flame propagation in terms of mean radius and velocity. Moreover, the interaction of turbulence with the local flame was evaluated. For both the engine configurations, it was observed that the addition of hydrogen results in a more efficient combustion, even though the engine configuration plays an important role. In PFI mode, the lower density of hydrogen causes a lower energy input. In DI mode, instead, the larger hydrogen diffusivity counteracts the charge stratification especially for larger hydrogen content. © 2016 Elsevier Ltd. All