• Energy Research
• Closed Access close
• Embargo close
• Renewable Energy close

Abstract Sunlight Concentrated and transmission for daylighting via optical fibers is a booming technology of direct utilization of solar energy. It uses optical fibers to introduce sunlight deep into building interior. In this work, a sunlight concentrating and transmitting system via plastic optical fibers was developed and tested. This study addressed the cooling problem of the plastic optical fibers under highly irradiation. Polymethylmethacrylate (PMMA) plastic fibers have a strong absorption effect on infrared light, which means that plastic fibers heat up so much when they transmit focused sunlight that they burn. In this study, a comprehensive cooling approach was developed to solve the overheating problem of plastic optical fibers, which consists of an infrared filter, cooling water and a homogenizer. The transmission efficiency of the system was measured to be about 15%. Experiments show that the comprehensive cooling measures developed can ensure that PMMA plastic optical fibers are in a safe temperature range. This shows that it is feasible to use low-cost plastic optical fibers instead of expensive silica fiber to transmit high flux for daylighting.

Abstract Bamboo has been considered a potential feedstock of energy for the future. It can be subjected to the pyrolysis for biofuels production. The thermogravimetric analysis (TGA) combined with differential thermogravimetric analysis (DTG) for bamboo was carried out prior to pyrolysis. The thermal degradation of bamboo was mainly between 230 and 420 °C. The conventional pyrolysis of bamboo was investigated in a bubbling fluidized-bed reactor using silica sand. The product distribution and composition of pyrolysis bio-oil were dependent on biomass component and operating conditions such as pyrolysis temperature, fluidization velocity, and particle size of biomass. The fractional catalytic pyrolysis of bamboo was also studied to upgrade the pyrolysis vapor, using HZSM-5 and red mud. The highest yield of bio-oil was 54.03 wt% compared to 49.14 wt% and 50.34 wt% of HZSM-5 and red mud catalyst, respectively. In the red mud catalytic pyrolysis, the oxygen content was rejected from pyrolysis vapor mostly via decarboxylation to produce more CO2 than CO; in contrast, for the HZSM-5 catalytic pyrolysis, the production of CO through decarbonylation was more favored than CO2. The main composition of catalytic pyrolysis bio-oil was 4-vinylphenol, which was employed as a raw material source to synthesize valuable material for energy storage.

In the present study, Tween 80, a non-ionic surfactant, has been used for enhanced hydrogen production by crude glycerol bioconversion using co-culture of Enterobacter aerogenes and Clostridium butyricum. The purpose of introducing the surfactant was to decrease the crude glycerol viscosity, so that apparent solubility and bioavailability of glycerol could be improved at the expenses of pretreatment steps. Experiments were planned using central composite design (CCD); crude glycerol and Tween 80 concentrations were optimized whereas, hydrogen production, glycerol utilization and viscosity of the media were considered as responses. The response surface for quadratic model showed, Tween 80 concentration had significant effect (p < 0.05) on all the three responses. Using the optimized conditions at 17.5 g/L crude glycerol and 15 mg/L Tween 80, hydrogen production reached a maximum of 32.1 ± 0.03 mmol/L of medium. The increase in hydrogen production was around 1.25-fold in presence of Tween 80 in comparison to its absence with 25.56 ± 0.91 mmol/L production. Selected optimum conditions were also validated against absence of crude glycerol (4.69 ± 0.76), with pretreated crude glycerol (20.06 ± 0.51) and across mono-culture system (15.43 ± 0.79 to 22.14 ± 0.94). Introduction of Tween 80 to the fermentation medium improved the glycerol utilization rate, resulting in increased hydrogen production and eliminated pretreatment steps.

Abstract This paper investigates the hydrodynamics of a seabed-mounted, bottom-hinged, flap-type wave energy converter in shallow water. A conceptual model of the hydrodynamics of the device has been formulated and shows that, as the motion of the flap is highly constrained, the magnitude of the wave force on the flap is the key determinant of power capture. The results from a physical modelling program have been used in conjunction with numerical data from WAMIT to validate the conceptual model. The work finds that designing the device to increase the wave force is more profitable than designing it to be tuned to the incident wave climate. As wave force is the primary driver of device performance it is shown that the flap should fill the water column and pierce the water surface to reduce decoupling due to wave overtopping. It is concluded that, in order to maximize capture factor at a typical North Atlantic site, the flap should be approximately 20–30 m wide, with large diameter rounded side edges, having its pivot close to the seabed and its top edge piercing the water surface.

Abstract Sugarcane is a major crop cultivated globally and the residue left over after the crop harvest and extraction of juice is a good biomass source that can be used for the production of several useful chemicals. The sugarcane bagasse is an excellent substrate for the production of various biochemicals and enzymes through fermentation. Now major interest is focused on the utilization of these residue for biofuel production. The sugarcane crop residue is rich in cellulose and hemicellulose, hence it can be used for the production of bioethanol and other liquid transportation fuels. The present review gives a detailed account of the availability of sugarcane residue and various commercially important products that can be produced from this residue. It also provides recent developments in R&D on the bioconversion of sugarcane crop residue for value added products.

Abstract To address the problem of fossil fuel usage at the Missouri University of Science and Technology campus, using of alternative fuels and renewable energy sources can lower energy consumption and hydrogen use. Biogas, produced by anaerobic digestion of wastewater, organic waste, agricultural waste, industrial waste, and animal by-products is a potential source of renewable energy. In this work, we have discussed Hydrogen production and End-Uses from CHHP system for the campus using local resources. Following the resource assessment study, the team selects FuelCell Energy DFC1500™ unit as a molten carbonate fuel cell to study of combined heat, hydrogen and power (CHHP) system based on a molten carbonate fuel cell fed by biogas produced by anaerobic digestion. The CHHP system provides approximately 650 kg/day. The total hydrogen usage 123 kg/day on the university campus including personal transportation applications, backup power applications, portable power applications, and other mobility applications are 56, 16, 29, 17, and 5 respectively. The excess hydrogen could be sold to a gas retailer. In conclusion, the CHHP system will be able to reduce fossil fuel usage, greenhouse gas emissions and hydrogen generated is used to power different applications on the university campus.