• Energy Research
• Restricted close
• 7. Clean energy close
• 11. Sustainability close
• 2. Zero hunger close
• 1. No poverty close

Artículos en revistas Liberalization policies, the challenges of integrating distributed generation resources, and the recent flattening of electricity demand due to the economic crisis and technological change have led to lower returns for European electricity suppliers. Innovative and sustainable business models are needed to serve electricity customers while reflecting the operational needs of the system and maintaining supplier financial viability. This paper describes a novel model of Integrated Energy Services that encompasses distributed generation (DG) and demand response (DR) resources for industrial customers. We further reflect on some of the market opportunities and regulatory drivers for the development of similar schemes across Europe. info:eu-repo/semantics/publishedVersion

Abstract The aerodynamic design of small wind turbines for the urban setting attracts increasing interest within the scientific community, but the adoption of a proper control strategy may be just as important, especially in high turbulent winds, where such energy conversion devices should ideally operate. As a matter of fact, the mere rotor efficiency is meaningless unless the system has also the capability of rapidly changing its angular speed in case of a sudden variation of the wind velocity, to reach a new optimal operating condition. This work will attempt neither to develop dynamic simulation models nor to examine possible turbine control strategies, being the focus much broader, namely, the investigation of operational contexts where the peculiar inertial characteristics of wind turbines would compromise any form of robust control. Inertial and operational data of commercially available turbines (characterized by both horizontal and vertical-axis architectures), as well as the results disseminated in various literature sources, operational experiences and design best practices, are here collected under one cover and compared, thus deriving some basic and fundamental relations between rotor inertia and angular acceleration, highlighting how, in several cases, a control strategy based on the continuous tracking of the optimal operating condition is most unlikely. Such considerations raise the question of whether the problem of inertia renders futile many prevailing theories about small wind turbine operation and plans for implementing new control strategies, especially as far as vertical axis architectures are concerned. On the other hand, some constructive advice is also presented, in the form of a means to compare the effective performances of different turbines, in a given installation site, with respect to their nominal (i.e. steady state, or wind tunnel) behaviour. As a final result, a new bound for a reliable estimation of the amount of energy a wind turbine will generate in a specific site is suggested, based on the comparison between a representative time scale of the installation site and the response time of the candidate wind turbine.

This chapter discusses the present scenario and market trend of regenerated cellulosic fibers, and the properties of principal fibers existing in the market as well as some new fibers recently developed and yet to be explored. Production technologies of these fibers are discussed and their potential applications are presented. Various sustainability issues related to the production of regenerated cellulosic fibers are dealt within this chapter. The last section discusses the results of research studies conducted to assess the environmental impacts and sustainability aspects of regenerated cellulose fibers. Serie: Textile science and clothing technology, ISSN 2197-9863

The development of heat transfer fluids (HTF) and heat storage materials (HSM) is crucial to design concentrating solar plant (CSP). Binary alkaline nitrate mixtures are currently used as sensible thermal energy storage materials. However, multi-component nitrate/nitrite systems were proposed as possible better candidates. In particular, ternaries mixtures containing sodium, potassium, and calcium are extremely promising as thermal fluids, given their reduced toxicity and greater cost-effectiveness. Nevertheless, very few data are present in the scientific literature regarding the correspondent phase diagram, and only the properties of specific compositions are reported. For this reason, a regular solution model was developed and employed in this work, and validated by comparing the simulation results with experimentally obtained phase change values. In particular, given that the common calorimetric techniques are impracticable for detecting the transition temperatures of calcium containing nitrate mixtur...

Saving energy in greenhouses is an important issue for growers. Here, we present a method to minimize the total energy that is required to heat and cool a greenhouse. Using this method, the grower can define bounds for temperature, humidity, CO2 concentration, and the maximum amount of CO2 available. Given these settings, optimal control techniques can be used to minimize energy input. To do this, an existing greenhouse climate model for temperature and humidity was expanded to include a CO2 balance. Heating, cooling, the amount of natural ventilation, and the injection of industrial CO2 were used as control variables.Standard optimization settings were defined in order to compare the grower's strategy with the optimal solution. This optimization resulted in a theoretical 47% reduction in heating, 15% reduction in cooling, and 10% reduction in CO2 injection for the year 2012. The optimal control does not need to maintain a minimum pipe temperature, in contrast to current practice. When the minimum pipe temperature strategy of the grower was implemented, heating and CO2 were reduced by 28% and 10% respectively.We also analyzed the effect of different bounds on optimal energy input. We found that as more freedom is given to the climate variables, the higher the potential energy savings. However, in practice the grower is in charge of defining the bounds. Thus, the potential energy savings critically depend on the choice of these bounds. This effect was analyzed by varying the bounds. However, because the effect can be demonstrated to the grower, the outcome has value to the grower with respect to decision making, an option that is not currently available in practice today.

<div class="section abstract"><div class="htmlview paragraph">The introduction of new light-duty vehicle emission limits to comply under real driving conditions (RDE) is pushing the diesel engine manufacturers to identify and improve the technologies and strategies for further emission reduction. The latest technology advancements on the after-treatment systems have permitted to achieve very low emission conformity factors over the RDE, and therefore, the biggest challenge of the diesel engine development is maintaining its competitiveness in the trade-off “CO₂-system cost” in comparison to other propulsion systems. In this regard, diesel engines can continue to play an important role, in the short-medium term, to enable cost-effective compliance of CO₂-fleet emission targets, either in conventional or hybrid propulsion systems configuration. This is especially true for large-size cars, SUVs and light commercial vehicles.</div><div class="htmlview paragraph">In this framework, a comprehensive approach covering the whole powertrain is of primary importance in order to simultaneously meet the performance, efficiency, noise and emission targets, and therefore, further development of the combustion system design and injection system represent important levers for additional improvements. For this purpose, a dedicated 0.5 dm³ single-cylinder engine has been developed and equipped with, a state-of-the-art Euro 6 combustion system, and an advanced common rail fuel injection system (FIS) offering higher flexibility in terms of injection strategy and higher quantity accuracy. Three injector nozzles with different hydraulic flow rates (HF) have been selected and employed for the overall combustion process optimization.</div><div class="htmlview paragraph">The optimization has been performed by means of an extensive DoE-based test campaign in which the engine and FIS operating parameters have been parametrized with the aim to carry out a proper combination in terms of HF and injection strategy. The results at partial load conditions evidence significant advantages in applying an advanced injection pattern, while the HF reduction can significantly improve the smoke emission and combustion noise without fuel consumption penalties. Therefore, a proper combination and optimization of the HF and injection strategy can provide low noise and engine-out smoke while maintaining the rated power performance targets.</div></div>

A Life Cycle Assessment (LCA) with focus on carbon footprint, followed by Life Cycle Costing (LCC) of municipal solid waste (MSW) management were conducted in a residential area of a medium-sized European city of 80,000 inhabitants. The initial results showed high environmental impacts and lack of economic sustainability, due to the high amounts of waste landfilled, the low extent of separate collection, low performance of mechanical-biological treatment as well as absence from alternatives to landfilling of non-recyclable materials. Taking this result as a baseline scenario, three improvement.s were tested with the aim of turning the carbon footprint of the local MSW management system into a neutral value: (i) increased separate collection of recyclables, (ii) enhanced biogas production and (iii) refuse-derived fuel (RDF) production. Successively adding the improvements, three alternative improved scenarios were defined, until reaching a negative carbon footprint, meaning that an optimised system would avoid GHG emissions. The proposed changes were sufficient to achieve carbon neutrality, as well as reduce overall environmental impacts, but were not enough for achieving economic sustainability due to the great influence of collection costs, especially for separate collection. It was concluded that by using an adequate combination of several treatment options and increasing the separate collection of recyclable materials it is possible to turn MSW management into a carbon neutral activity as well as improve its economic balance.

In Vietnam, the energy demand shows an ever-increasing trend. To limit the utilization of fossil fuels and the following consequences for the environment, renewable energy sources must be adopted. In this context, the paper assesses the utilization of offshore wind and sea wave, by considering a commercial wind turbine and a prototypical wave energy converter. Solar energy can be optionally also collected by this device. An algorithm is introduced to find the best composition of the three sources able to cover a desired share of energy demand. The approach is applied to Ca Mau, a province in the southern part of Vietnam. Finally, the results encourage the adoption of these energy sources that could be easily implemented up to a share of the local energy demand equal to 65%.