• Energy Research
• UK Research and Innovation close
• 11. Sustainability close
• 6. Clean water close
• 9. Industry and infrastructure close

This dataset contains two metrics for climate change exposure using downscaled climate projections with the SRES A2 emissions scenario (Tabor and Williams, 2007).The metrics represent dissimilarity measurements of the squared Euclidean distance between seasonal (June–August and December–February) temperature and precipitation variables in the 20th century climate and mid-21st century climate. (1) disappearing climate risk - measure of dissimilarity between a pixel’s late 20th century climate and its closest matching pixel in the global set of 21st-century climates (2) novel climate risk - measure of dissimilarity between a pixel’s future climate and its closest matching pixel in the global set of late 20th-century climates. The data are in arcASCII format. All data are in units of standard Euclidean distance and multiplied by 1000. This is the original data. To scale the data similar to Tabor et al. (2018), remove outliers above the 99th percentile distribution before rescaling from 0-1. Unprojected number of columns 2160 number of rows 857 Lower Left X Center -179.917 Lower Left Y Center -59.084 Cell size 0.166667 decimal degrees (10 minutes or ~17 km) {"references": ["Tabor, K. et al. (2018). Tropical Protected Areas Under Increasing Threats from Climate Change and Deforestation: https://doi.org/10.3390/land7030090", "Tabor and Williams (2010). Globally downscaled climate projections for assessing the conservation impacts of climate change. https://doi.org/10.1890/09-0173.1", "Williams, J.W. et al. (2007). Projected distributions of novel and disappearing climates by 20100 AD. https://doi.org/10.1073/pnas.0606292104"]} Support for this project was provided by Conservation International, the Land Tenure Center at the University of Wisconsin, the Center for Climatic Research at the University of Wisconsin, and the Environment Program at the University of Wisconsin–Madison. This research has been funded in part by the Walton Family Foundation, the Gordon and Betty Moore Foundation, and a gift from Betty and Gordon Moore.

This dataset contains time series of reservoir releases (including any spills), evaporation loss, and rule curves for the Pong and Bhakra reservoirs, India. {"references": ["https://doi.org/10.3390/w11071413", "https://doi.org/10.1016/j.scitotenv.2019.06.021"]}

Climate change, environmental degradation, and limited resources are motivations for sustainable forest management. Forests, the most abundant renewable resource on earth, used to make a wide variety of forest-based products for human consumption. To provide a scientific measure of a product’s sustainability and environmental performance, the life cycle assessment (LCA) method is used. This article provides a comprehensive review of environmental performances of forest-based products including traditional building products, emerging (mass-timber) building products and nanomaterials using attributional LCA. Across the supply chain, the product manufacturing life-cycle stage tends to have the largest environmental impacts. However, forest management activities and logistics tend to have the greatest economic impact. In addition, environmental trade-offs exist when regulating emissions as indicated by the latest traditional wood building product LCAs. Interpretation of these LCA results can guide new product development using biomaterials, future (mass) building systems and policy-making on mitigating climate change. Key challenges include handling of uncertainties in the supply chain and complex interactions of environment, material conversion, resource use for product production and quantifying the emissions released.

Driven by the need to develop a wide variety of products with low environmental impact, biorefineries need to emerge as highly integrated facilities. This becomes effective when overall mass and energy integration through a centralised utility system design is undertaken. An approach combining process integration, energy and greenhouse gas (GHG) emission analyses is shown in this paper for Jatropha biorefinery design, primarily producing biodiesel using oil-based heterogeneously catalysed transesterification or green diesel using hydrotreatment. These processes are coupled with gasification of husk to produce syngas. Syngas is converted into end products, heat, power and methanol in the biodiesel case or hydrogen in the green diesel case. Anaerobic digestion of Jatropha by-products such as fruit shell, cake and/or glycerol has been considered to produce biogas for power generation. Combustion of fruit shell and cake is considered to provide heat. Heat recovery within biodiesel or green diesel production and the design of the utility (heat and power) system are also shown. The biorefinery systems wherein cake supplies heat for oil extraction and seed drying while fruit shells and glycerol provide power generation via anaerobic digestion into biogas achieve energy efficiency of 53 % in the biodiesel system and 57 % in the green diesel system. These values are based on high heating values (HHV) of Jatropha feedstocks, HHV of the corresponding products and excess power generated. Results showed that both systems exhibit an energy yield per unit of land of 83 GJ ha−1. The global warming potential from GHG emissions of the net energy produced (i.e. after covering energy requirements by the biorefinery systems) was 29 g CO2-eq MJ−1, before accounting credits from displacement of fossil-based energy by bioenergy exported from the biorefineries. Using a systematic integration approach for utilisation of whole Jatropha fruit, it is shown that global warming potential and fossil primary energy use can be reduced significantly if the integrated process schemes combined with optimised cultivation and process parameters are adopted in Jatropha-based biorefineries.

The increasing depletion of natural resources, combined with a wider set of pressures on the environment, has, in recent years, highlighted the need for a more efficient use of energy and a development process that involves alternative energy sources. Energy efficiency has received much attention as a solution, implying both monetary and emissions savings. However, the latter may be partially offset by the income and demand effects of the former, both in more efficient sectors and in spreading to the wider economy. This is the problem of rebound effects. Taking Spain as a case study, and introducing an energy-related CGE model that develops the inclusion of renewables, this paper evaluates a combination of efficiency initiatives to deliver both reduced energy use by households and a more sustainable supply of energy. Our findings suggest that a package aimed at improving efficiency in household electricity and petroleum use, combined with a more competitive supply of energy from renewable sources, may be the only way to get reductions in all energy use, and thus benefit the economy. Specifically, we consider how this package may lead to positive economic impacts and associated rebound effects, where the latter are focused on a greener energy supply.

The decarbonisation of heating in the United Kingdom is likely to entail both the mass adoption of heat pumps and widespread development of district heating infrastructure. Estimation of the spatially disaggregated heat demand is needed for both electrical distribution network with electrified heating and for the development of district heating. The temporal variation of heat demand is important when considering the operation of district heating, thermal energy storage and electrical grid storage. The difference between the national and urban heat demands profiles will vary due to the type and occupancy of buildings leading to temporal variations which have not been widely surveyed. This paper develops a high-resolution spatiotemporal heat load model for Great Britain (GB: England, Scotland a Wales) by identifying the appropriate datasets, archetype segmentation and characterisation for the domestic and nondomestic building stock. This is applied to a thermal model and calibrated on the local scale using gas consumption statistics. The annual GB heat demand was in close agreement with other estimates and the peak demand was 219 GWth. The urban heat demand was found to have a lower peak to trough ratio than the average national demand profile. This will have important implications for the uptake of heating technologies and design of district heating.

Optimisation results for the lowest lifetime cost system consisting of solar photovoltaic (PV), hybrid photovoltaic-thermal (PV-T) and solar-thermal collectors alongside battery and hot-water storage systems for meeting the electrical and thermal (hot-water) needs of three multi-effect distillation (MED) plants. The updated results are from optimisations runs carried out in response to peer-review comments.