• Energy Research
• Open Access close
• Open Source close
• English close

Abstract This work test the feasibility and characterize the thermohygric properties of composite materials, realized with eco-friendly raw materials and designed to make suspended ceilings or interior partition walls. Several raw materials are considered: recycled paper (granules or cellulose wadding) and wood fibers. Aggregates or fibers are bonded with organic or mineral binder. One of the binder considered is starch, due to its availability in Ivory Coast (cassava flour). The calcium sulfate hemihydrate is also used for comparison. The density of the produced composites ranges from 400 to 1200 kg/m3 depending on formulation. The thermal conductivity increases proportionally with the density and ranges from 0.09 to 0.5 W/(m.K). The characterization of hygric behavior is based on the measurement of moisture buffer value (MBV) [1]. The hydric performances of the composites made of mineral binder goes from moderate (MBV around 1 g/(m².%RH)) to excellent (MBV > 2 g/(m².%RH)). The moisture buffer value of the paper granules -starch composite is also excellent (MBV > 2 g/(m².%RH))

Heat pump (HP) technology has been widely adopted in electric vehicles (EVs) for cabin and battery heating in cold weather due to its high efficiency. However, when an HP works under low ambient temperatures and high humidity, frost grows on the surface of the outdoor evaporator, deteriorating system efficiency. This study experimentally investigated the performance of an automotive reversible CO2 HP system under cyclic frosting–defrosting conditions, with different defrost-initiation criteria and orientations of the outdoor heat exchanger. The relationship between the performance degradation of the heat pump system and the feature of frost accumulation on the outdoor heat exchanger is analyzed. The experimental data revealed that the heating capacity of the HP system only mildly degrades (~30%), even with an air-side pressure drop of the outdoor heat exchanger growing 10 times, which enables the system to work in HP mode for a longer time before the defrosting without significantly impacting passengers’ comfort. The horizontally installed outdoor heat exchanger is proven to have better refrigerant distribution, but with approximately a 0.16 bar (11.9%) higher pressure drop, reducing the evaporating temperature by about 0.4 K. Consequently, frost accumulates faster, and the working time in HP mode is shortened by 12 min (18.2%). Moreover, the vertical outdoor heat exchanger drains much more water during the defrosting. As a result, the defrosting time for the vertical outdoor heat exchanger is reduced by 17%.

We compare the behavior of the finite-temperature Hartree-Fock model with that of thermal density functional theory using both ground-state and temperature-dependent approximate exchange functionals. The test system is bcc Li in the temperature-density regime of warm dense matter (WDM). In this exchange-only case, there are significant qualitative differences in results from the three approaches. Those differences may be important for Born-Oppenheimer molecular dynamics studies of WDM with ground-state approximate density functionals and thermal occupancies. Such calculations require reliable regularized potentials over a demanding range of temperatures and densities. By comparison of pseudopotential and all-electron results at ${\mathrm T} = 0$K for small Li clusters of local bcc symmetry and bond-lengths equivalent to high density bulk Li, we determine the density ranges for which standard projector augmented wave (PAW) and norm-conserving pseudopotentials are reliable. Then we construct and use all-electron PAW data sets with a small cutoff radius which are valid for lithium densities up to at least 80 g/cm$^3$.

The gene of Thermotoga maritima GH10 xylanase (TmXYN10B) was synthesised to study the extreme limits of this hyperthermostable enzyme at high temperatures in the presence of biomass-dissolving hydrophilic ionic liquids (ILs). TmXYN10B expressed from Pichia pastoris showed maximal activity at 100 °C and retained 92 % of maximal activity at 105 °C in a 30-min assay. Although the temperature optimum of activity was lowered by 1-ethyl-3-methylimidazolium acetate ([EMIM]OAc), TmXYN10B retained partial activity in 15-35 % hydrophilic ILs, even at 75-90 °C. TmXYN10B retained over 80 % of its activity at 90 °C in 15 % [EMIM]OAc and 15-25 % 1-ethyl-3-methylimidazolium dimethylphosphate ([EMIM]DMP) during 22-h reactions. [EMIM]OAc may rigidify the enzyme and lower V max. However, only minor changes in kinetic parameter K m showed that competitive inhibition by [EMIM]OAc of TmXYN10B is minimal. In conclusion, when extended enzymatic reactions under extreme conditions are required, TmXYN10B shows extraordinary potential.

A quasi-static analysis and sensitivity investigation of two different mooring configurations—a single anchor leg mooring (SALM) and a three-legged catenary anchor leg system (CALM)—is presented. The analysis aims to indicate what can be expected in terms of requirements for the mooring system size and stiffness. The two mooring systems were designed for the same reference load case, corresponding to a horizontal design load at the wave energy converter (WEC) of 2000 kN and a water depth of 30 m. This reference scenario seems to be representative for large WECs operating in intermediate water depths, such as Weptos, Wave Dragon and many others, including reasonable design safety factors. Around this reference scenario, the main influential parameters were modified in order to investigate their impact on the specifications of the mooring system, e.g. the water depth, the horizontal design load, and a mooring design parameter.

In the context of climate change and rural revitalization, numerous solar photovoltaic (PV) panels are being installed on village roofs and lands, impacting the enjoyment of the new rural landscape characterized by PV panels. However, the visual acceptance of PV panels in rural areas of China is not yet fully understood. This study aims to identify and correlate three key influential factors that contribute to the acceptance and appreciation of PV panels in China’s rural settings. A quasi-experiment was conducted, incorporating diverse landscapes into six rural settings, each containing both the original landscape and PV panels. The findings demonstrated that the original rural landscape was significantly more scenic than PV panels, and factors contributing to the appreciation of traditional landscapes, such as nostalgia, played a vital role in rejecting PV panels. Conversely, renewable energy-related factors, such as economic stakes and moral desirability, were found to contribute to the acceptance of PV panels. This study contributes to the strategic planning and design of solar PV panels in rural landscapes, taking into consideration social acceptance and local contexts.

(Uploaded by Plazi for the Bat Literature Project) This note is based on a literature search and a recent review of bat mortality data from wind farms in Europe (published elsewhere). We suggest that mortality of bats at wind turbines may be linked to high-altitude feeding on migrating insects that accumulate at the turbine towers. Modern wind turbines seem to reach high enough into the airspace to interfere with the migratory movements of insects. The hypothesis is consistent with recent observations of bats at wind turbines. It is supported by the observation that mortality of bats at wind turbines is highly seasonal (August–September) and typically peaks during nights with weather conditions known to trigger large-scale migratory movements of insects (and songbirds). We also discuss other current hypotheses concerning the mortality of bats at wind turbines.