• Energy Research
• 13. Climate action close
• 4. Education close
• Applied Energy close

Abstract A great deal of heat is wasted in intensive public shower facilities, such as those in schools, barracks and natatoriums, which open up at specified time. It will contribute a lot to energy saving and environmental protection with significant economic benefits to recycle the exhaust heat. In this paper, we propose two different kinds of heat pumps (an electric heat pump and an absorption heat pump) in the heat recovery systems. In both system, the used shower water is drained through a pipe and collected in a gray water pool. When the wastewater reaches certain volume, the heat pump system will begin working and recycling heat. The wastewater is filtered and piped to the heat exchanger to exchange heat with the tap water whose temperature will increase from 12 °C to 25 °C with the wastewater temperature dropping from 30 °C to 17 °C. Then the wastewater is piped to the heat pump evaporator and the tap water is piped to the condenser for farther heating. According to the different characteristics of the electric heat pump and absorption heat pump, we also introduce the processes and control methods of different heat recovery systems in details in this paper. Based on a practical example, this paper analyzes and compares the economic and environmental benefits of three retrofitting schemes, including “exhaust heat recovery using electric heat pump”, “exhaust heat recovery using electric heat pump + gas boiler” and “exhaust heat recovery using direct-fired heat pump”. Then we find out that the heat recovery system using direct-fired absorption heat pump has lower energy consumption, less pollution, lower operating cost, and shorter payback period. And it has a promising practical application.

Abstract Adsorbent-based carbon capture is only feasible if adsorption-desorption cycles are both fully regenerating and efficient. This work proposes a regenerative pH swing process and a pH swing regenerative adsorbent that are inspired by natural CO2 conversion by carbonic anhydrase biocatalysts found in mammalian red blood cells. The main objective is to develop, test and analyze a synthetic pH Swing Adsorption (pHSA) system as well as a pHSA compatible solid adsorbent to capture CO2 from a simulated ambient air gas stream. The lead developed adsorbent is a carbon black co-activated with potassium carbonate and nitrogenous copolymer that is impregnated with immobilized bovine carbonic anhydrase and thereby deemed “BCA/KN-CB”. BCA/KN-CB has preliminarily demonstrated both competitive CO2 adsorption capacity and limited regenerative ability under experimental pHSA conditions. In addition, BCA-based adsorbents achieved higher adsorption capacities than non-BCA adsorbent counterparts. The BCA/KN-CB adsorbent displayed both large point of zero charge (PZC) swings and regenerative stability. The proposed pHSA system requires essentially zero energy expenditure to achieve intended environments for capture and regeneration. With 1 kg of adsorbent, pHSA has the ability to capture 1 kg CO2 in less than 4 h of cycling. The tested pHSA adsorbent can also capture more than 96% of total CO2 in a given raw gas stream flowing through the capture chamber. This proof-of-concept study of a pH swing adsorption/biocatalytic adsorbent system suggests the potential to effectively operate under ambient conditions and exhibit advantageous operational efficiencies to other high-profile CO2 capture systems.

Abstract For 118 million residential housing units in the U.S., there is currently a gap between the potential energy savings that can be achieved through the use of existing energy efficiency technologies, and the actual level of energy savings realized, particularly for the 37% of housing units that are considered residential rental properties. Additional quantifiable benefits are needed beyond energy savings to help further motivate residential property owners to invest in energy efficiency upgrades. This research focuses on assessing the adoption of energy efficient upgrades in U.S. residential housing and the impact on rental prices. Ten U.S. cities are chosen for analysis; these cities vary in size across multiple climate zones, and represent a diverse set of housing market conditions. Data was collected for over 159,000 rental property listings, their characteristics, and their energy efficiency measures listed in rental housing postings across each city. Following an extensive data quality control process, over thirty different types energy efficient features were identified. The level of adoption was determined for each city, ranging from 5.3% to 21.6%. Efficient lighting and appliances were among the most common, with many features doubling as energy efficient and other desirable aesthetic or comfort improvements. Then using propensity score matching and conditional mean comparison methods, the relative impact on rent charged in each city was calculated, which ranged from a 6% to 14.1% increase in rent for properties with energy efficient features, demonstrating a positive economic impact of these features, particularly for property owners. This was further subdivided into five types of energy efficiency upgrade and three housing types. Single family homes generally demanded higher premiums with energy efficient features, however there was not a consistent pattern across the types of efficient upgrades. The results of this work demonstrate that investment in energy efficient technologies has quantifiable benefits for rental property owners in the U.S. beyond just energy savings. This methodology and results can also be used in other cities and by property owners, utility companies, or others, ultimately encouraging further investment and positive economic impact in residential energy efficiency and in turn improving energy and resource conservation in the building sector.

Abstract Specification by central government of the heating levels which are to be maintained in British school buildings has recently been altered. This paper is concerned with examining the nature of changes that have been made by comparing present requirements with their counterparts during the preceding one hundred years. Attention is focused on the apparently contradictory implications of these changes for those charged with responsibility for maintaining heating levels in school buildings while, at the same time, conserving fuel. It is suggested that the new statutory requirements present those who are responsible with a duty which may, in practical terms, prove difficult or costly to discharge. Although discussion is specifically restricted to British school buildings, issues are raised which are pertinent to attempts to integrate regulation of heating with control of fuel consumption in other types of non-domestic buildings both in Britain and abroad.

Abstract Hydrothermal treatment (HT) is one of the efficient approaches for upgrading municipal solid waste (MSW). In the present study, emission characteristics of polycyclic aromatic hydrocarbons (PAHs) from hydrothermally treated municipal solid waste (H-MSW) combustion alone and H-MSW/coal co-combustion were investigated at different temperatures. The results showed that for all fuel combustion, the majority of PAHs were 3- or 4-ring PAHs. In addition, flue gas had the highest yields of PAHs followed by fly ash and bottom ash, while the ring number of dominated PAHs in fly ash was higher than those in flue gas and bottom ash. Compared to MSW, H-MSW combustion generated less PAHs at the value of 1131.95–7649.24 μg/g. The blending of H-MSW and coal reduced total PAH emissions and positive interactions were observed between H-MSW and coal during co-combustion. The toxicity equivalent quantity (TEQ) values of the PAHs from combustion were in the order MSW > H-MSW > H-MSW/coal, which was consistent with the total PAH emissions. The present study illustrated that significant reduction of PAH emissions and toxicity from combustion could be achieved by HT and the blending of H-MSW and coal.

Metal-based fuel-borne catalysts (FBCs) have been used with diesel fuels to effectively reduce soot and diesel particulate matter (DPM) emissions from both on-road and off-road applications. However, there is a lack of detailed investigations on the potential changes in the properties of particulates, when FBCs-doped fuels are combusted in diesel engines. This study fully evaluates the potential impacts of ferrocene-doped ultralow sulfur diesel (ULSD) fuels on physical, chemical and toxicological characteristics of the particulates emitted by a single cylinder, direct-injection diesel engine working at a constant speed and at three engine loads. The results indicated that ferrocene-doped fuels could effectively reduce the particulate mass and elemental carbon (EC) emissions, while increasing the proportion of both organic carbon (OC) and water-soluble organic carbon (WSOC) in particles. Particle-phase PAHs and n-alkanes emissions increased with an increase of Fe in the fuels. Ferrocene addition also led to lower soot ignition temperature and activation energy. However, the total number emissions of particles from ferrocene-doped fuels dramatically increased due to the formation of Fe-rich nuclei mode particles. Compared to pure ULSD, the particles emitted from ferrocene-doped fuels showed a slight decline in cell viability. The Fe in the particles and the changes in chemical composition of particulates are thought to be responsible for the variation of cell viability.

Abstract The Biofuels Directive sets reference values for the quantity of biofuels and other renewable fuels to be placed on the transport market. Biogas from agricultural crops can be used to meet this directive. This paper investigates biogas production for three crop rotations: wheat, barley and sugar beet; wheat, wheat and sugar beet; wheat only. A technical and economic analysis for each crop rotation was carried out. It was found that wheat produces significantly more biogas than either barley or sugar beet, when examined on a weight basis. However sugar beet produces more biogas and subsequently more energy when examined on an area basis. When producing biofuels, land is the limiting factor to the quantity of energy that may be produced. Thus if optimising land then a crop rotation of wheat, wheat and sugar beet should be utilised, as this scenario produced the greatest quantity of energy. This scenario has a production cost of €0.90/mN3, therefore, this scenario is competitive with petrol when the price of petrol is at least €1.09/l (VAT is charged at 21%). If optimising the production costs then a crop rotation of wheat only should be utilised when the cost of grain is less than €132/ton. This scenario has the least production cost at €0.83/mN3, therefore, this scenario is competitive with petrol when the price of petrol is at least €1.00/l. But as this scenario produces the least quantity of biogas, it also produces the least quantity of energy. In comparing with other works by the authors it is shown that a biomethane system produces more energy from the same crops at a cheaper cost than an ethanol system.

Abstract The South Korean government has been actively promoting an educational-facility improvement program as part of its energy-saving efforts. This research seeks to develop a decision support model for selecting the facility expected to be effective in generating energy savings and making the facility improvement program more effective. In this research, project characteristics and electric-energy consumption data for the year 2009 were collected from 6282 elementary schools located in seven metropolitan cities in South Korea. In this research, the following were carried out: (i) a group of educational facilities was established based on electric-energy consumption, using a decision tree; (ii) a number of similar projects were retrieved from the same group of facilities, using case-based reasoning; and (iii) the accuracy of prediction was improved, using the combination of genetic algorithms, the artificial neural network, and multiple regression analysis. The results of this research can be useful for the following purposes: (i) preliminary research on the systematic and continuous management of educational facilities’ electric-energy consumption; (ii) basic research on electric-energy consumption prediction based on the project characteristics; and (iii) practical research for selecting an optimum facility that can more effectively apply an educational-facility improvement program as a decision support model.

Thermal generation is a vital component of mature and reliable electricity markets. As the share of renewable electricity in such markets grows, so too do the challenges associated with its variability. Proposed solutions to these challenges typically focus on alternatives to primary generation, such as energy storage, demand side management, or increased interconnection. Less attention is given to the demands placed on conventional thermal generation or its potential for increased flexibility. However, for the foreseeable future, conventional plants will have to operate alongside new renewables and have an essential role in accommodating increasing supply-side variability.\ud \ud This paper explores the role that conventional generation has to play in managing variability through the sub-system case study of Northern Ireland, identifying the significance of specific plant characteristics for reliable system operation. Particular attention is given to the challenges of wind ramping and the need to avoid excessive wind curtailment. Potential for conflict is identified with the role for conventional plant in addressing these two challenges. Market specific strategies for using the existing fleet of generation to reduce the impact of renewable resource variability are proposed, and wider lessons from the approach taken are identified.