This project will develop sound methods for future climate change data for building designers to use for new buildings and refurbishments that could last to the end of this century. The principal application output will be a draft Technical Memorandum (TM) for the Chartered Institution of Building Services Engineers, CIBSE, suitable for practising designers. This will be supported by extensive case studies to validate the new weather data design methodology and be used in research tasks described later. 'Story lines' relevant to different scenarios for the climate and built environment will be developed as well as risk levels in building design to enable designers to use the weather data with confidence. The TM will provide CIBSE with a consistent methodology for the selection and use of future data for its new Design Guide, a fundamental document used by designers of buildings and their services and a supporting document for the Government's Building Regulations. The basis for this project will be the UK Climate Impacts Programme (UKCIP) future scenarios to be published in 2008 (UKCIP08) from which may be derived probabilities of different weather outcomes over this century. Academic outputs will include an extensive assessment of the carbon reduction potential of active and passive systems and designs for new and refurbished buildings. They will utilise case studies with PC simulation of the building and systems, employing the new probabilistic weather data. These assessments will provide designers and policy makers with guidelines to help reduce the growth in greenhouse gases (GHGs) from buildings, which at present contribute about 50% of the UK emissions. Other academic outputs will provide the theoretical basis underlying the proposed consistent PC-based and manual design methodology with coincident, probabilistic future weather data parameters such as solar radiation, air temperature, wind speed and direction. It is known that solar radiation and air temperature have peak values at different times and on different days but current design methods do necessarily separate them so that over-design often occurs. A related academic output will be a theory underpinning the selection of the proposed new Design Reference Year (DRY) which will facilitate building design (including passive and active heating and cooling systems and comfort assessment) with simulation on a PC. The DRY will replace the currently unsatisfactory Design Summer Year. Solar radiation data, not covered in detail in the HadRM3 and UKCIP02 models, will be developed to satisfy designers' requirements. Likewise wind data (crucial to include since wind drives natural ventilation) although the confidence level will be lower. Rainfall duration and quantity are also important in the building design process because of drainage and rain penetration damage and designers' requirements will again be reviewed.'Urban heat island' effects (urban areas are often hotter than the nearby rural areas), briefly mentioned in the present Guide, will be incorporated in the new data, developing on SCORCHIO work to provide more realistic urban weather data. Local modification or downscaling will also be applied to generate data for other sites in the UK. This will enable the new Guide to cover more than the current 14 sites for which data were developed by Manchester for CIBSE.To ensure that the new, probabilistic outputs will be useful to professionals, and to reflect best practice in design, there will be strong stakeholder involvement through the formation of a Stakeholders Group, including Corresponding Members, which will include CIBSE, architects and software houses and housebuilders. Policy interests will be reached via the Department for Communities and Local Government, and DEFRA and their contractors, such as BRE. There will be links to the Manchester-led EPSRC SCORCHIO urban heat island and climate change project, UKCIP and the Tyndall Centre.

Nearly half of the total energy generation in the developed world is inefficiently used to heat, cool, ventilate and control humidity in buildings. Unfortunately, the concepts developed through many research and demonstration projects have struggled to become assimilated into main-stream construction. In Europe, the most successful passive design standard, the German PassivHaus standard, has certified only 30,000 buildings in 15 years. Comparing this with the UK Government's 2016 target for the construction of 240,000 new homes per year and current quarterly output of around 29,380 homes it is evident that additional routes to achieving low and zero energy buildings must be investigated and developed if deep cuts in energy use and associated carbon emissions are to be attained by the building sector. Furthermore, there must be a focus on whole-life impact. To achieve the space heating energy targets of the PassivHaus standard, walls typically require insulation to a thickness of at least 300 mm and this level of conventional insulation material significantly increases the embodied energy content of the finished building. At present, inorganic insulation materials dominate the building industry, although interest in the use of natural fibre insulation products is steadily increasing. In Europe inorganic fibrous materials, e.g. stone wool and glass wool, account for 60% of the market. Organic foamy materials such as expanded and extruded polystyrene account for 27% of the market, whilst all other materials combined make up less than 13%. In the case of the mineral fibre materials adhesives are often added as are water-repellent oils as both increase mechanical strength. Expanded and extruded polystyrene are both oil-based polymerised polystyrol and the production process requires blowing agents which, since the phase-out of ozone depleting materials, are typically pentane and carbon dioxide, respectively. Pentane contributes to smog and ground level ozone and carbon dioxide, due to its low solubility and high diffusivity in polymers, make it difficult to produce low density foams which result in poorer thermal performance compared with those insulation materials made using HCFC blowing agents. Natural fibre insulation (NFI) can be seen as an excellent form of carbon emission mitigation. NFI not only reduces the in-service carbon emissions of buildings through reduced energy demands, but through the use of plant based fibres carbon is stored within the material, as a result of plant photosynthesis, so significantly reducing the global warming impact of the insulation material. However, much is unknown about the performance of NFI materials. Where evidence-based data are available they are almost universally based on steady-state test performance data rather than the more complex dynamic variations experienced in real buildings. Frequently, where test data relating to thermal conductivity are presented, it is based on standard test conditions of a material in a dry state and at one mean temperature. Accordingly practitioners use such test results for prediction of in-service energy performance or evaluation of retrofit benefits, often without consideration for variability due to the changeability in the thermo-physical properties of the material or the validity of the test conditions. Whilst this situation affects all building materials attempts have been made to evaluate sensitivity and the impact on energy performance for more conventional products but there is little evidence of the same approach for NFI. Furthermore, the hygroscopic nature of NFI materials results in much greater variability in their thermal performance. The primary aim of this project is the quantification of the dynamic thermal performance of NFI materials through experiment and simulation, which will help to support a growing 'green economy' and provide valuable data for building designers and developers of building simulation models.

The increasing demand for low and zero carbon buildings in the UK has provided significant challenges for the energy intensive materials we currently rely on. At present somewhere between 20% and as much as 60% of the carbon footprint of new buildings is attributable to the materials used in construction; this is predicted to rise to over 95% by 2020. If the UK is to meet agreed 80% carbon reduction targets by 2050 it is clear that significant reductions in the embodied carbon of construction materials is required. What also seems clear is that current materials and systems are not capable of delivering these savings. The drive for an 80% reduction in carbon emissions, a decreasing reliance on non-renewal resources and for greater resource efficiency, requires step changes in attitude and approach as well as materials. Improvement in construction systems, capable of providing consistently enhanced levels of performance at a reasonable cost is required. Modern developments in construction materials include: eco-cements and concretes (low carbon binders); various bio-based materials including engineered timber, hemp-lime and insulation products; straw based products; high strength bio-composites; unfired clay products utilising organic stabilisers; environmentally responsive cladding materials; self healing materials; smart materials and proactive monitoring; hygrothermal and phase change materials; coatings for infection control; ultra thin thermally efficient coatings (using nano fillers); ultra high performance concretes; greater use of wastes; and, fibre reinforcement of soils. However, very few of these innovations make the break through to widespread mainstream use and even fewer offer the necessary step change in carbon reductions required A low carbon approach also requires novel solutions to address: whole life costing; end of life (disassembly and reuse); greater use of prefabrication; better life predictions and longer design life; lower waste; improved quality; planned renewal; and greater automation in the construction process. As well as performance, risk from uncertainty and potentially higher costs other important barriers to innovation include: lack of information/demo projects; changing site practices and opposition from commercial competitors offering potentially cheaper solutions.. A recent EPSRC Review has recognised the need for greater innovation in novel materials and novel uses of materials in the built environment. The vision for our network, LIMES.NET, is to create an international multi-disciplinary community of leading researchers, industrialists, policy makers and other stakeholders who share a common vision for the development and adoption of innovative low impact materials and solutions to deliver a more sustainable built environment in the 21st Century. The scope of LIMES.NET will include: adaptive and durable materials and solutions with significantly reduced embodied carbon and energy, based upon sustainable and appropriate use of resources; solutions for retrofitting applications to reduce performance carbon emissions of existing buildings and to minimise waste; climate change resilient and adaptive materials and technologies for retrofitting and new build applications to provide long term sustainable solutions. In recognition of their current adverse impacts and potential for future beneficial impacts, LIMES.NET will focus on bringing together experts to develop pathways to solutions using: renewable (timber and other plant based) construction materials; low-impact geo-based structural materials; cement and concrete based materials; innovative nano-materials and fibre reinforced composites. Through workshops and international visits the network will create a roadmap for multidisciplinary research and development pathways that will lead to high quality large research proposals, and an on-going virtual on-line centre of excellence.

The decarbonisation of industrial clusters is of critical importance to the UK's ambitions of cutting greenhouse gas emissions to net zero by 2050. The UK Industrial Decarbonisation Challenge (IDC) of the Industrial Strategy Challenge Fund (ISCF) aims to establish the world's first net-zero carbon industrial cluster by 2040 and at least one low-carbon cluster by 2030. The Industrial Decarbonisation Research and Innovation Centre (IDRIC) has been formed to support this Challenge through funding a multidisciplinary research and innovation centre, which currently does not exist at the scale, to accelerate decarbonisation of industrial clusters. IDRIC works with academia, industry, government and other stakeholders to deliver the multidisciplinary research and innovation agenda needed to decarbonise the UK's industrial clusters. IDRIC's research and innovation programme is delivered through a range of activities that enable industry-led, multidisciplinary research in cross-cutting areas of technology, policy, economics and regulation. IDRIC connects and empowers the UK industrial decarbonisation community to deliver an impactful innovation hub for industrial decarbonisation. The establishment of IDRIC as the "one stop shop" for research and innovation, as well as knowledge exchange, regulation, policy and key skills will be beneficial across the industry sectors and clusters. In summary, IDRIC will connect stakeholders, inspire and deliver innovation and maximise impact to help the UK industrial clusters to grow our existing energy intensive industrial sectors, and to attract new, advanced manufacturing industries of the future.

This project will develop sound methods for future climate change data for building designers to use for new buildings and refurbishments that could last to the end of this century. The principal application output will be a draft Technical Memorandum (TM) for the Chartered Institution of Building Services Engineers, CIBSE, suitable for practising designers. This will be supported by extensive case studies to validate the new weather data design methodology and be used in research tasks described later. 'Story lines' relevant to different scenarios for the climate and built environment will be developed as well as risk levels in building design to enable designers to use the weather data with confidence. The TM will provide CIBSE with a consistent methodology for the selection and use of future data for its new Design Guide, a fundamental document used by designers of buildings and their services and a supporting document for the Government's Building Regulations. The basis for this project will be the UK Climate Impacts Programme (UKCIP) future scenarios to be published in 2008 (UKCIP08) from which may be derived probabilities of different weather outcomes over this century. Academic outputs will include an extensive assessment of the carbon reduction potential of active and passive systems and designs for new and refurbished buildings. They will utilise case studies with PC simulation of the building and systems, employing the new probabilistic weather data. These assessments will provide designers and policy makers with guidelines to help reduce the growth in greenhouse gases (GHGs) from buildings, which at present contribute about 50% of the UK emissions. Other academic outputs will provide the theoretical basis underlying the proposed consistent PC-based and manual design methodology with coincident, probabilistic future weather data parameters such as solar radiation, air temperature, wind speed and direction. It is known that solar radiation and air temperature have peak values at different times and on different days but current design methods do necessarily separate them so that over-design often occurs. A related academic output will be a theory underpinning the selection of the proposed new Design Reference Year (DRY) which will facilitate building design (including passive and active heating and cooling systems and comfort assessment) with simulation on a PC. The DRY will replace the currently unsatisfactory Design Summer Year. Solar radiation data, not covered in detail in the HadRM3 and UKCIP02 models, will be developed to satisfy designers' requirements. Likewise wind data (crucial to include since wind drives natural ventilation) although the confidence level will be lower. Rainfall duration and quantity are also important in the building design process because of drainage and rain penetration damage and designers' requirements will again be reviewed.'Urban heat island' effects (urban areas are often hotter than the nearby rural areas), briefly mentioned in the present Guide, will be incorporated in the new data, developing on SCORCHIO work to provide more realistic urban weather data. Local modification or downscaling will also be applied to generate data for other sites in the UK. This will enable the new Guide to cover more than the current 14 sites for which data were developed by Manchester for CIBSE.To ensure that the new, probabilistic outputs will be useful to professionals, and to reflect best practice in design, there will be strong stakeholder involvement through the formation of a Stakeholders Group, including Corresponding Members, which will include CIBSE, architects and software houses and housebuilders. Policy interests will be reached via the Department for Communities and Local Government, and DEFRA and their contractors, such as BRE. There will be links to the Manchester-led EPSRC SCORCHIO urban heat island and climate change project, UKCIP and the Tyndall Centre.