• Energy Research
• Bioresource Technology close
• Energy Research close

Dried, milled perennial ryegrass samples were processed using chemical and physical treatments and the extracted cellulose products were analysed for yield, crystallinity by X-ray Diffraction (XRD) and for purity using Thermogravimetric Analysis (TGA), Pyrolysis-Gas Chromatography/Mass Spectrometry (Py-GC/MS) and Fourier Transform Infrared (FTIR) spectroscopy. Extraction protocols examined the use of chemical chelation, acid and alkaline hydrolysis, along with physical degradation methods. Highest product yields were obtained using single step chemical protocols followed by physical processing, however, these products had low crystallinity and higher amorphous fraction content. Multistep chemical processing to completely remove hemicellulose and lignin with an alkali refluxing step, delivered lower yielding cellulose products of greater crystallinity and purity. In combination, the four instrumental techniques highlighted removal of amorphous fractions, providing rapid, accurate compositional data on the extracted cellulose products.

In this study, levulinic acid (LA) was produced from rice straw biomass in co-solvent biphasic reactor system consisting of hydrochloric acid and dichloromethane organic solvent. The modified protocol achieved a 15% wt LA yield through the synergistic effect of acid and acidic products (auto-catalysis) and the designed system allowed facile recovery of LA to the organic phase. Further purification of the resulting extractant was achieved through traditional column chromatography, which yielded a high purity LA product while recovering ∼85% wt. Upon charcoal treatment of the resultant fraction generated an industrial grade target molecule of ∼99% purity with ∼95% wt recovery. The system allows the solvent to be easily recovered, in excess of 90%, which was shown to be able to be recycled up to 5 runs without significant loss of final product concentrations. Overall, this system points to a method to significantly reduce manufacturing cost during large-scale LA preparation.

Microalgae are promising sources of valuable compounds: carotenoids, polyunsaturated fatty acids, lipids, etc. To overcome the feasibility challenge due to low yield and attain commercial potential, researchers merge technologies to enhance algal bioprocess. In this context, nanomaterials are attractive for enhancing microalgal bioprocessing, from cultivation to downstream extraction. Nanomaterials enhance biomass and product yields (mainly lipid and carotenoids) through improved nutrient uptake and stress tolerance during cultivation. They also provide mechanistic insights from recent studies. They also revolutionize harvesting via nano-induced sedimentation, flocculation, and flotation. Downstream processing benefits from nanomaterials, improving extraction and purification. Special attention is given to cost-effective extraction, showcasing nanomaterial integration, and providing a comparative account. The review also profiles nanomaterial types, including metallic nanoparticles, magnetic nanomaterials, carbon-based nanomaterials, silica nanoparticles, polymers, and functionalized nanomaterials. Challenges and future trends are discussed, emphasizing nanomaterials' role in advancing sustainable and efficient microalgal bioprocessing, unlocking their potential for bio-based industries.

Algae production process is a key cost center in production of biofuels/bioproducts from microalgae. Decline in the growth of algae in outdoor ponds during non-optimal conditions is one of the hurdles for achieving consistently high algal production rates. An optimal controller can be used to overcome this limitation and provide reliable growth in outdoor conditions. A model predictive controller (MPC) was developed to optimize the algal growth, predicted by flux balance analysis, under natural disturbances, embedding within the cost function, the economic and environmental constraints associated with the process. The model, developed in MATLAB, was validated on a 30-L continuous algal culture under light, temperature and a combination of light and temperature disturbances. The MPC proved effective in minimization of a decrease in growth under these natural disturbances. The growth rates with MPC were observed to be 79-116% higher as compared to the non-MPC growth.

The possibility of using anaerobic digestate effluent (ADE) to replace freshwater and nutrients for bioethanol production was explored. The ethanol concentration yielded from ADE and post-centrifuged ADE supernatant was 79.60±1.75 g/L and 78.33±1.66 g/L, respectively, with a 24% dry mass (DM) of soft wheat. Ethanol production was enhanced in ADE by as much as 18% in comparison to the production in freshwater (66.61±0.28 g/L, p<0.01). Without yeast nutrients, ADE fermentation yielded an ethanol concentration of 81.10±2.87 g/L, which was significantly higher than that in freshwater fermentation (59.67±1.79 g/L). Analysis showed that ADE contained rich nitrogen, proteins and minerals. After one-step distillation, the ethanol concentration attained was 700.05±46.20 g/L in ADE as compared to 622.79±32.22 g/L in freshwater (p<0.05).

To find an appropriate method for sulfate-rich wastewater containing ethanol and acetate with COD/sulfate ratio of 1, a UASB reactor was operated for more than 180 days. The influences of HRT (hydraulic retention time) and OLR (organic loading rate) on organics and sulfate removal, gas production, and electrons utilization were investigated. The sludge activity and microorganism composition were also determined. The results indicated that this system removed more than 80% of COD and 30% of sulfate with HRT above 6h and OLR below 12.3 gCOD/L d. Further HRT decrease caused volatile fatty acids accumulation and performance deterioration. Except at HRT of 2h, COD and electron flow were mostly utilized by methane-producing archaea (MPA), and methane yield remained in the range of 0.18-0.24 LCH4/gCOD. Methane was mainly generated by Methanosaeta concilii GP6 with acetate as substrate, whereas sulfate was mainly reduced by incomplete-oxidizing Desulfovibrio species with ethanol as substrate.

Large-size woody biomass is a valuable renewable resource to replace fossil fuels in biorefinery processes. The preprocessing of wood chips and briquettes is challenging to manage, especially in an industrial setting, as it generates a significant amount of dust and noise and occasionally causes unexpected accidents. As a result, a substantial amount of resources, energy, labor, and space are needed. The thermochemical conversion behavior of large-size woody biomass was studied to reduce energy consumption for chipping. Large-size wood was 1.5 m in length, 0.1 m in breadth, and stacked 90 cm in height. This strategy has many benefits, including increased effectiveness and reduced CO2 emissions. The target of this paper presents the thermochemical process, and large-size wood was chosen because it provides high-quality product gas while reducing the preprocessing fuel cost. This review examines the benefits of thermochemical conversion technologies for assessing the likelihood of carbon neutrality.

In this study, pyrolysis of microalgal remnants was investigated for recovery of energy and nutrients. Chlorella vulgaris biomass was first solvent-extracted for lipid recovery then the remnants were used as the feedstock for fast pyrolysis experiments using a fluidized bed reactor at 500 °C. Yields of bio-oil, biochar, and gas were 53, 31, and 10 wt.%, respectively. Bio-oil from C. vulgaris remnants was a complex mixture of aromatics and straight-chain hydrocarbons, amides, amines, carboxylic acids, phenols, and other compounds with molecular weights ranging from 70 to 1200 Da. Structure and surface topography of the biochar were analyzed. The high inorganic content (potassium, phosphorous, and nitrogen) of the biochar suggests it may be suitable to provide nutrients for crop production. The bio-oil and biochar represented 57% and 36% of the energy content of the microalgae remnant feedstock, respectively.

This work aims the study of decomposition kinetics of guarana seed residue using thermogravimetric analyzer under synthetic air atmosphere applying heating rates of 5, 10, and 15°C/min, from room temperature to 900°C. Three thermal decomposition stages were identified: dehydration (25.1-160°C), oxidative pyrolysis (240-370°C), and combustion (350-650°C). The activation energies, reaction model, and pre-exponential factor were determined through four isoconversional methods, master plots, and linearization of the conversion rate equation, respectively. A scheme of two-consecutive reactions was applied validating the kinetic parameters of first-order reaction and two-dimensional diffusion models for the oxidative pyrolysis stage (149.57kJ/mol, 6.97×10(10)1/s) and for combustion stage (77.98kJ/mol, 98.611/s), respectively. The comparison between theoretical and experimental conversion and conversion rate showed good agreement with average deviation lower than 2%, indicating that these results could be used for modeling of guarana seed residue.

To fix CO2 emissions efficiently from flue gas of coal-fired power plants, the culture medium, light intensity and bioreactors were comprehensively optimized in the process of CO2 fixation by Chlorella PY-ZU1. To make up for relative insufficiency of nutrients (except for the carbon source) resulting from continuous bubbling of 15% CO2, three chemicals were added into the culture to optimize the molar ratios of nitrogen to carbon, phosphorus to carbon, and magnesium to carbon in culture from 0.17 to 0.69, from 0.093 to 0.096, and from 0.018 to 0.030, respectively. Such adjustments led to a 1.25-fold increase in biomass (from 2.41 to 5.42 g L(-1)). By enhancing light intensity from 4500 to 6000 lux, the peak growth rate of Chlorella PY-ZU1 increased by 99% and reached to 0.95 g L(-1) day(-1). Use of a multi-stage sequential bioreactor notably improved the peak CO2 fixation efficiency to 85.6%.