• Energy Research
• engineering and technology close
• 11. Sustainability close
• 6. Clean water close
• AU close
• JP close

China’s research on and specific implementation of energy saving for buildings are mainly concentrated in urban areas, but according to 2016 statistics, the rural population accounts for 42.65% of the total population, so rural housing has considerable energy-saving potential. However, the degree of attention to the energy consumption of rural houses needs to be improved. Regarding the research on and implementation of passive energy-saving strategies for residences, compared with centralized urban high-rise residences, rural residences mainly have independent courtyards, with a flexible layout and easier transformation. In this study, a system that uses the common cold lanes in traditional villages and buildings’ exterior walls was constructed, and the indoor spaces of courtyard buildings in southern Shaanxi were completely passively cooled in summer. This system can be completely separated from the supply of artificial energy by relying on the accumulation and buoyancy effects of air in patios and cold lanes and the hot-pressure ventilation in buildings to cool the buildings and greatly improve indoor ventilation efficiency. As the building is ventilated and cooled, the air wall formed in the system can effectively prevent direct contact between the outdoor and indoor temperatures and reduce the impact of thermal wall radiation on the interior. In previous studies on the passive design of courtyard houses, scholars considered the effect of thermal wall radiation on indoor temperature in simulations. Therefore, in this study, we also separately calculated whether to consider the difference between the situation with and without wall heat radiation (WHR) when simulating thermal conversion. The final results show that when the cooling system was adopted, the annual cooling load of the whole building was 4786.494 kW·h without WHR. However, with WHR, the cooling load reduction was 2989.128 kW·h, a difference of 1797.336 kW·h.

This paper presents a multi-objective optimization model for a long-term generation mix in Indonesia. The objective of this work is to assess the economic, environment, and adequacy of local energy sources. The model includes two competing objective functions to seek the lowest cost of generation and the lowest CO2 emissions while considering technology diffusion. The scenarios include the use of fossil reserves with or without the constraints of the reserve to production ratio and exports. The results indicate that Indonesia should develop all renewable energy and requires imported coal and natural gas. If all fossil resources were upgraded to reserves, electricity demand in 2050 could be met by domestic energy sources. The maximum share of renewable energy that can be achieved in 2050 is 33% with and 80% without technology diffusion. The least cost optimization produces lower generation costs than the least CO2 emissions, as well as the combined scenario. Total CO2 emissions in 2050 are five to six times as large as current emissions. The least CO2 emissions scenario can reduce almost half of the CO2 emissions of the least cost scenario by 2050. The proposed multi-objective optimization model leads some optimal solutions for a more sustainable electricity system.

This study aims to identify potential hydropower sites and calculate the theoretical potential hydropower capacity based on watershed modelling of the Mindanao River Basin (MRB) in the Philippines for the sustainable development of a previously unstudied region. The Soil and Water Assessment Tool (SWAT) was applied to delineate the watershed of the MRB and simulate the river discharges with inputs from observed precipitation and global gridded precipitation datasets. Observed weather data, such as temperature, humidity, and solar radiation, from four meteorological stations in the Philippines were also used as inputs for SWAT modelling. Simulated discharges were calibrated at three river gauges on the Nituan, Libungan and Pulangi Rivers. However, due to limited river discharge records, model validations were conducted in proxy basins: the calibrated model parameters in river A were used in the watershed modelling of proxy river B. Of the delineated 107 sub-basins in the MRB watershed, only 33 were identified as having potential sites for hydropower development. These potential sub-basins hosted a total of 154 potential sites with an estimated monthly average power capacity of 5,551.35 MW for all 33 sub-basins. The estimated theoretical power capacity of 15,266.22 MW for all sites in the MRB is approximately equivalent to the Philippines’ total available power capacity in 2017 of 15,393 MW. These sites were classified into 16 mini-scale hydropower sites, 114 small-scale hydropower sites and 24 medium-scale hydropower sites based on the simulated river discharges and potential power capacities. Based on these results, hydropower development could be an alternative to strengthen the exploration of renewable energy resources and improve the energy situation in Mindanao; hydropower development could also have mitigation effects on frequent floods in flat, low-lying downstream areas.

AbstractA simple experiment for capillary sealed trap shows that leakage would occur only from the weakest point in the trap. As an extens ion of this concept, the sequestrated and accumulated CO2 in the structural high may happen to leak from the unexpected weak point near the top of sealing layer. On the other hand, if CO2 were sequestrated into the flank of tilted aquifer, CO2 in separate phas e would migrate upward within aquifer with no CO2 leakage into the sealing layer above and leaving some residual amount behind. According to this concept, the best location for sequestration of CO2 could be the flank of the structure rather than the top.

Abstract Light wells in the centers of high-rise apartment buildings in Japan are called ‘Voids’. Gas water-heaters built into Voids discharge exhaust gas so a large enough opening has to be designed at the bottom of a Void to keep the indoor air quality (IAQ) acceptable. In order to secure the IAQ in the Void from contamination, a simple calculation method of the ventilation rate induced by wind force and thermal buoyancy through openings at the bottom, along with heat sources such as water-heaters, is presented. The accuracy of this calculation method was examined by wind tunnel testing. As a result, it turned out that the simple calculation methods introduced in this study were valid for predicting the vertical temperature distribution and ventilation rates in Voids.

COVID-19 pandemic has brought tremendous environmental burden due to huge amount of medical wastes (about 54,000 t/d as of November 22, 2020), including face mask, gloves, clothes, goggles, and sanitizer/disinfectant containers. A proper waste management is urgently required to mitigate the spread of the disease, minimize the environmental impacts, and take their potential advantages for further utilization. This work provides a prospective review on the possible thermochemical treatments for those COVID-19 related medical wastes (CMW), as well as their possible conversion to fuels. The characteristics of each waste are initially analyzed and described, especially their potential as energy source. It is clear that most of CMWs are dominated by plastic polymers. Thermochemical processes, including incineration, torrefaction, pyrolysis, and gasification, are reviewed in terms of applicability for CMW. In addition, the mechanical treatment of CMW into sanitized refuse-derived fuel (SRDF) is also discussed as the preliminary stage before thermochemical conversion. In terms of material flexibility, incineration is practically applicable for all types of CMW, although it has the highest potential to emit the largest amount of CO2 and other harmful gasses. Furthermore, gasification and pyrolysis are considered promising in terms of energy conversion efficiency and environmental impacts. On the other hand, carbonization faces several technical problems following thermal degradation due to insufficient operating temperature.

Sustainability has emerged, arguably, as the premiere mission of contemporary architecture. Green assessment tools abound, consultancy services flourish, buildings are marketed on the basis of sustainability performance, and government, media, and corporations seem preoccupied with assessing the quality of the built environment through a green lens. Yet for all the effort, and indeed for all the progress made, fundamental issues resistant to the structural change that is essential for genuine sustainability remain. This paper reviews the state of play of sustainability across the urban landscape. It considers the road travelled so far, and points out some of the major challenges that lie ahead.

Abstract. The last half century has witnessed the increasing trend of renewable energy utilization with solar photovoltaic (PV) systems as one of the most popular option. Solar PV continues to supplement the main grid in powering both commercial establishments (mainly for reduced electricity expense) as well as residential houses in isolated areas (for basic energy requirement such as for lighting purposes). The objective of this study is to assess the available solar PV power (PPV) potential considering the effects of high temperature, dust and snow in the Asia Pacific region. The PPV potential was estimated considering the effects of the said meteorological parameters using several satellite data including shortwave radiation from Advanced Himawari Imager 8 (AHI8), MOD04 aerosol data from Moderate Resolution Imaging Spectroradiometer (MODIS), precipitation rate from Global Satellite Mapping of Precipitation (GSMaP), air temperature from NCEP/DOE AMIP-II Reanalysis-2 data, and snow water equivalent (SWE) from Microwave Scanning Radiometer for the Earth Observing System (AMSR-E). The model is validated by comparing its outputs with the measured PV power from two solar PV installations in Bangkok, Thailand and Perth, Australia. Results show that maximum PPV is estimated at 2.5 GW (cell efficiency of 17.47%) for the region with the maximum decrease in PPV estimated to be about < 2%, 22% and 100% due to high temperature (temperature coefficient of power = 0.47%/K), dust and snow, respectively. Moreover, areas in India and Northern China were observed to experience the effects of both dust and temperature during March-April-May (MAM) season. Meanwhile, countries located in the higher latitudes were severely affected by snow while Australia by high temperature during Dec-Jan-Feb (DJF) season. The model has a mean percentage prediction error (PPE) range of 5% to18% and 7% to 23% in seasonal and monthly estimations, respectively. Outputs from this study can be used by stakeholders of solar PV in planning for small-scale or large-scale solar PV projects in the solar rich region of Asia Pacific.