• Energy Research
• Restricted close
• IT close
• AU close
• Trees and Timber Institute close

Castor (Ricinus communis L.) is an oilseed species, which in southern Italy is cultivated as annual during the spring-summer period under irrigation, but in most temperate areas such as those of eastern coast of Sicily, it could be grown as semiperennial with no irrigation, by the adoption of autumnal sowings. A field experiment was conducted in southeastern Sicily with the aim of assessing plant surviving, seed yield and oil quality of four castor genotypes originating from different geographical areas (two Sicilian, one Tunisian and one Brazilian). The favorable climatic conditions allowed the plant to survive during the fall-winter period. Seed yield reached 3.45 t ha-1 on average of the two years and seed oil content ranged from 45% (Tunisian cultivar) to 48% ('Local RG 2' Sicilian genotype). Oil yield reflected the variation in seed yield. Genetic diversity for fatty acid composition and saponification number, iodine value and cetane number was evidenced. When ricinoleic acid is not taken into account, the oil of all genotypes satisfied the E.U. standards for biodiesel. The ricinoleic acid was the lowest (79%) in the Sicilian 'Local RG 2' and the highest (89%) in the Tunisian one, revealing a greater suitability of oil of the first genotype for biodiesel. In turn, the oil of Tunisian genotype could be exploited in other bio-based industrial sectors. The study also demonstrated that in the southeastern coast of Sicily autumnal sowings might be advantageous for castor grown as semi-perennial crop, mainly since they allow saving irrigation water.

Wood biomass is turned into industrial fuel through chipping. The efficiency of chipping depends on many factors, including chipper knife wear. Chipper knife wear was determined through a long-term follow-up study, conducted at a waste wood recycling yard. Knife wear determined a sharp drop of productivity (>20%) and a severe decay in product quality. Dry sharpening with a grinder mitigated this effect, but it could not replace proper wet sharpening. Increasing the frequency of wet sharpening sessions determined a moderate increase of knife depreciation cost, but it could drastically enhance machine performance and reduce biomass processing cost. Since benefits largely exceed costs, increasing the frequency of wet sharpening sessions may be an effective measure for reducing overall chipping cost. If the main goal of a chipper operator is to increase productivity and/or decrease fuel consumption, then managing knife wear should be a primary target. (C) 2014 Elsevier Ltd. All rights reserved.

This is the longest continuous experiment where ethylenediurea (EDU) was used to protect plants from ozone (O3). Effects of long-term ambient O3 exposure (23 ppm h AOT40) on biomass of an O3 sensitive poplar clone (Oxford) were examined after six years from in-ground planting. Trees were irrigated with either water or 450 ppm EDU. Above (-51%) and below-ground biomass (-47%) was reduced by O3 although the effect was significant only for stem and coarse roots. Ambient O3 decreased diameter of the lower stem, and increased moisture content along the stem of not-protected plants (+16%). No other change in the physical wood structure was observed. A comparison with a previous assessment in the same experiment suggested that O3 effects on biomass partitioning to above-ground organs depend on the tree ontogenetic stage. The root/shoot ratios did not change, suggesting that previous short-term observations of reduced allocation to tree roots may be overestimated.

The study tested the use of a trommel screen originally designed for compost materials to reject oversize particles from hog fuel, processed from several sources and by two different comminution devices. The experiment consisted in screening material previously comminuted by a convertible crusher, designed to use both hammers and knives. Three different feedstock types were used, and namely: discarded pallets, logs and branches from park maintenance. Each feedstock type came in two different qualities, depending on the tool used for comminution, i.e. hammers or knives. Trommel screen productivity varied between 4.2 t h-1, and 5.2 t h-1 of oven dry material. Screening hog fuel derived from pallets was 30% and 40% less productive than screening fuel derived from logs and branches, respectively. Screening cost varied from 16.2 EUR t-1 dry material in the case of branches, to 19.9 EUR t-1 oven dry material for pallets. Screening allowed an increase of fuel quality only when applied to pallet-derived hog fuel.

A commercial drum chipper was fed alternately and piecewise with poplar stems and poplar tops, in order to determine the effect of piece size and tree part on machine performance. Chipping stems required most of the available power (231 kW) delivered by the tractor, whereas chipping tops took about half that much. However, productivity was twice as high with stems, compared to tops (i.e. 25 and 11 t h-1 of oven dry wood, respectively). As a consequence, specific fuel consumption per unit product was 15% lower with stems, compared to tops - i.e. 0.61 and 0.72 L m-3, respectively. Mean feeding speed was 0.37 m s-1 for stems and 0.41 m s-1 for tops, but the difference was not significant (p = 0.1677). Productivity and fuel consumption were strongly related to piece size, but tree part had its own additional effect, independent from size and possibly related to form. When chipping tops it is advisable to feed more pieces at a time, in order to partly compensate for the effect of piece size. Operators expecting to chip primarily small-size materials may acquire special chipper versions with wider drums and additional side rollers, for smoother mass feeding. oThe same chipper was tested with poplar stems and tops.oChipping stems resulted in higher productivity and lower fuel consumption.oChipping stems required most of the available tractor power.oChip particle size distribution was about the same for both feedstocks. © 2013 Elsevier Ltd.

In Italy, olive tree groves may offer up to a million tonnes of dry biomass per year as pruning residue. Searching for a cost-effective way to tap this potential, the authors tested a new machine, capable of recovering pruning residue at the same time as pruning. The pre-commercial prototype was tested on four different plots and compared to a simpler tractorbase mechanical pruning unit. The authors conducted detailed time-studies in order to determine machine productivity and residue recovery cost. The integrated machine can treat between 0.2 and 0.6 ha h(-1), producing between 0.33 and 1.03 tonnes of fresh residue hour(-1). Its integrated residue recovery function does not slow the pruning, which actually proceeds faster than with the tractor-base unit, due to the more efficient multiple-disc cutting bar. The marginal cost of residue recovery hovers around 40-45 (sic) fresh tonne(-1). However, the new machine must not be considered just as a biomass harvester, but rather as a mechanical pruning unit with an integrated biomass recovery function. Its main benefit derives from the capacity of performing a very effective mechanical pruning, and the residue recovery function is a secondary benefit yet unavailable on standard pruning machines. Its deployment must be seen in the context of a general effort to modernize olive grove management and to develop an integrated biomass production system, rather than as a further attempt to build a specialised biomass supply chain.

The Authors tested a complete new system for recovering wood fuel from the termination of depleted orchards. This operation can generate between 25 and 80 fresh t ha?¹, that can be directed to the growing bioenergy sector. The new system is based on highly-mobile low-investment general-purpose equipment, which allows containing operational cost and speeding relocation between work sites. The new residue collection system is quite flexible, and achieves cost-effective recovery on relatively small fields, often smaller than 1 ha. Under the conditions of the study, trees are cut, chipped and delivered at a cost between 35 and 40 EUR t?¹ (40% water mass fraction), provided that fields are within a 20 km distance from the biomass plant. Use of a standard drum chipper results in a better product quality than if a grinders is used, as is the case for conventional orchard removal operations. Feeding the chipper with a separate loader allows a significant cost reduction, provided that the field offers at least 25 t of fresh wood. In the future, use of remote controls and electronic tethers may allow a further cost reduction, which is estimated at 15%.

Industrial poplar plantations represent a strategic source of wood products for many countries. Harvested after 10 to 30 years, they yield about 200 t ha-1 of timber and 100 t ha-1 industrial wood. The latter is obtained from poplar tops, which can be converted into chips, or a mix of pulpwood and chips. The study compared four options to process poplar tops. Alternatives derived from the intersection of two product strategies (pulpwood and chips, or chips only) with two pulpwood processing methods (manual or mechanized). Both mechanization and simplification (only one product) succeeded in reducing production cost, but the former had a stronger effect. The tests demonstrated that all options were cost-effective and could return some profits. However, the exclusive production of chips offered lower profits, compared to an articulate product strategy aimed at maximising value recovery. In the case of Italian poplar plantations, the price difference between pulp and chips is generally larger than the cost reduction obtained with integral chipping. Similar conclusions were reached by other authors working with spruce and beech in Central Europe. Of course, this is only true for the current price levels of pulpwood and chips: results may change, if this price balance will be altered by the growing demand for biomass fuel.