• Energy Research
• Restricted close
• 7. Clean energy close
• 11. Sustainability close
• 3. Good health close
• AU close
• PK close

Abstract Thermal energy storage systems for both heat and cold are necessary for many industrial processes. High energy density and high power capacity are desirable properties of the storage. The use of latent heat increases the energy density of the storage tank with high temperature control close to the melting point. Tube in PCM tank is a very promising system that provides high packing factor. This work presents an experimental study of a PCM tank for cold storage applications. Two different configurations and different flow rates of the heat transfer fluid were studied. The effectiveness of the PCM storage system was defined as that of a heat exchanger. The results showed that the heat exchange effectiveness of the system did not vary with time, decreased with increasing flow rate and increased with increasing heat transfer area. The effectiveness was experimentally determined to only be a function of the ratio m ˙ /A. This equation was found to be adequately be used to design a PCM storage system, and a case study is presented. It was shown that the tube in tank design together with a low temperature PCM is suitable as a thermal storage facility for cold storage.

A commercial drum chipper was fed alternately and piecewise with poplar stems and poplar tops, in order to determine the effect of piece size and tree part on machine performance. Chipping stems required most of the available power (231 kW) delivered by the tractor, whereas chipping tops took about half that much. However, productivity was twice as high with stems, compared to tops (i.e. 25 and 11 t h-1 of oven dry wood, respectively). As a consequence, specific fuel consumption per unit product was 15% lower with stems, compared to tops - i.e. 0.61 and 0.72 L m-3, respectively. Mean feeding speed was 0.37 m s-1 for stems and 0.41 m s-1 for tops, but the difference was not significant (p = 0.1677). Productivity and fuel consumption were strongly related to piece size, but tree part had its own additional effect, independent from size and possibly related to form. When chipping tops it is advisable to feed more pieces at a time, in order to partly compensate for the effect of piece size. Operators expecting to chip primarily small-size materials may acquire special chipper versions with wider drums and additional side rollers, for smoother mass feeding. oThe same chipper was tested with poplar stems and tops.oChipping stems resulted in higher productivity and lower fuel consumption.oChipping stems required most of the available tractor power.oChip particle size distribution was about the same for both feedstocks. © 2013 Elsevier Ltd.

In Italy, olive tree groves may offer up to a million tonnes of dry biomass per year as pruning residue. Searching for a cost-effective way to tap this potential, the authors tested a new machine, capable of recovering pruning residue at the same time as pruning. The pre-commercial prototype was tested on four different plots and compared to a simpler tractorbase mechanical pruning unit. The authors conducted detailed time-studies in order to determine machine productivity and residue recovery cost. The integrated machine can treat between 0.2 and 0.6 ha h(-1), producing between 0.33 and 1.03 tonnes of fresh residue hour(-1). Its integrated residue recovery function does not slow the pruning, which actually proceeds faster than with the tractor-base unit, due to the more efficient multiple-disc cutting bar. The marginal cost of residue recovery hovers around 40-45 (sic) fresh tonne(-1). However, the new machine must not be considered just as a biomass harvester, but rather as a mechanical pruning unit with an integrated biomass recovery function. Its main benefit derives from the capacity of performing a very effective mechanical pruning, and the residue recovery function is a secondary benefit yet unavailable on standard pruning machines. Its deployment must be seen in the context of a general effort to modernize olive grove management and to develop an integrated biomass production system, rather than as a further attempt to build a specialised biomass supply chain.

Electricity generation integrated with xylose degradation was investigated in a two-chamber mediator-less microbial fuel cell (MFC). Voltage output followed saturation kinetics as a function of xylose concentration for concentration below 9.7 mM, with a predicted maximum of 86 mV (6.3 mW m(-2) or 116 mW m(-3)) and half-saturation constant (K(s)) of 0.29 mM. Xylose concentrations from 0.5 mM to 1.5 mM resulted in coulombic efficiencies and maximum voltage ranging from 41+/-1.6% to 36+/-1.2% and 55+/-2.0 mV to 70+/-3.0 mV respectively. Xylose degradation rate increased with increasing xylose concentration up to 9.7 mM and the predicted maximum degradation rate was 0.13 mM h(-1) and K(s) of 3.0 mM. Stirring by nitrogen in the anode chamber led to 99+/-2.3 mV maximum voltage (8.4+/-0.4 mW m(-2) or 153+/-7.1 mW m(-3)) and 5.9+/-0.3% coulombic efficiency at MFC running time 180 h, which were respectively 17+/-1.2% and 37+/-1.8%, higher than those without stirring. The COD removal under stirring was 22.1+/-0.3%, which was slightly lower than that of 23.7+/-0.4% under no stirring. However, stirring resulted in 59% lower xylose degradation rate. This work demonstrates that xylose can be used in the MFC for electricity production. Comparatively higher electricity generation and coulombic efficiency can be obtained by adjusting initial xylose concentration and applying stirring in the anode chamber.

Abstract This Special Section provides introduction to the 15th Conference Process Integration, Modelling and Optimisation for Energy Saving and Pollution Reduction (PRES 2012). In this editorial introduction, the editors are highlighting the individual articles included in this issue and discussing the main points. The main areas of this issue can be summarised as: Process Integration for Energy Saving, Integrating Renewable Energy Sources and Energy Optimisation issues.

The authors tested a 409kW forager turned into an industrial chipper through a special conversion kit. Conversion was temporary, and the forager could be returned to its original occupation with one day of work. The converted forager proved as effective as a dedicated chipper of the same power. Net chipping productivity varied between 25 and 33greenth-1. Productivity was highest with poplar tops and lowest with pine tops. Fuel consumption ranged from 1.6 to 1.8lgreent-1. Fuel consumption did not change with tree species, but increased significantly with knife wear. Temporary conversion allowed a better depreciation of the invested capital and resulted in a 25% reduction of unit chipping cost. The converted forager proved an ideal solution wherever the production of wood chips was a complementary business within the scope of a larger agricultural economy. In technical terms, this machine offered the combined advantages of road-capability and good off-road mobility, allowing low-cost independent relocation and effective in-field chipping. © 2013 Elsevier Ltd.

Large-scale photovoltaic (PV) plants enable the reduction of the PV plant cost per watt of nominal power that is installed. In this paper, a new method is presented for the calculation of the optimal configuration of large PV plants, such that the levelized cost of the generated electricity (LCOE) is minimized. The proposed design optimization process is performed by considering the impact of the number of components, as well as their type and arrangement within the installation field, on the tradeoff between the lifetime cost and the corresponding energy production of the PV plant. The high-accuracy feature of the energy production calculations that are performed by the proposed design tool has been validated using experimental operational data of an existing PV plant. The design results demonstrate that using the proposed optimization method allows a reduction of the cost of the energy that is generated by the large-scale PV plant, thus enabling the maximization of the economic benefit that is obtained during the operational lifetime period of the PV system.

The Authors surveyed 6 industrial chipping operations for a whole work year, collecting data about machine usage, product output, fuel consumption and chipper knife wear. Despite the challenging work conditions offered by mountain operations, industrial chipping contractors manage to achieve a high machine use, ranging from 500 to over 2,500 h year(-1). Product output varies between 18,000 and over 120,000 m(3) loose chips per year. In order to acquire enough jobs, operators may travel between 1,500 to over 20,000 km in a year. Industrial chipping contractors adopt different operational strategies to achieve their production targets, and they equip accordingly. Some operators prefer to tap smaller local areas and opt for smaller tractor-powered chippers, which are less powerful and productive than larger independent-engine units, but cheaper and capable of negotiating low-standard forest roads. Others prefer to explore larger areas and achieve higher product outputs, and they opt for larger independent-engine chippers, often mounted on trucks. Long term productivity varies with machine type: tractor-powered units produce between 40 and 50 m3 loose chips per hour, whereas larger independent-engine chippers produce between 60 and 90 m3 loose chips per hour. Specific fuel consumption is about 0.5 L diesel per m3 loose chips, regardless of chipper type. A sharp knife set can process between 200 and 1,500 m3 loose chips before getting dull. Disposable knives last longer and are cheaper to manage than standard re-usable knives. (C) 2014 Elsevier Ltd. All rights reserved.