• Energy Research
• Restricted close
• Open Source close
• Embargo close
• IT close
• US close
• DE close
• BE close

Abstract A unique large scale pilot plant of the CellFlux thermal energy storage concept is experimentally investigated. This storage concept consists of a regenerator type thermal energy storage volume, which is coupled to a finned tube heat exchanger by a circulating intermediate working fluid. The system investigated in this work operates at a temperature of 390 °C and uses air as intermediate working fluid which is conveyed by a centrifugal fan. The storage volume has a bed length of over ten meters and is of a novel design, where the air flows in horizontal direction. Since this approach could cause a flow maldistribution, a thorough analysis is of major interest for the accuracy of subsequent numerical simulations. The experiments reveal that the mass flow along the centerline can be up to 20% higher than the mean bulk flow. A significant maldistribution between top and bottom area, however, is not observed. As an alternative to the typically used rock filling, the storage volume is equipped with standard hollow bricks. These bricks are cost effective but do not have a well-defined shape. Thus, the predictability of the pressure drop by correlations found in the literature is unclear. It turns out that the measured pressure drop is evenly distributed in axial flow direction but generally higher than expected from the assumption of pure channel flow. Further experiments are conducted to validate the heat capacity of the bricks and to derive a correlation for the inner heat transfer between bricks and storage walls. Eventually, the aim of the experimental investigation is a general proof of concept as basis for the numerical investigation. Thus, all specifications of the plant and the storage material are provided. The plant is analyzed towards plausibility of heat losses, showing that heat losses can be predicted well within the given uncertainties.

Environment preservation, energy, and the growing economy are becoming strongly interconnected themes requiring new solutions to be exploited. An example of this interconnection is the demand for the development of almost zero-energy buildings, i.e. buildings capable to be almost autonomous from external energy supply or at least not dependent on the energy supply from utilities. The actual conception of a zero energy building is a very complex system formed by several subsystems, with the consequence that costs are very high and reliability relatively low. The aim of this research program is to deepen the possibility to employ the Stirling engine and cooler technology to lower the number of components required in a near zero-energy building, increase the efficiency, and contemporary raise the reliability of the overall system. Stirling cooler could be used to convert mechanical work into heating and cooling effects and produce the temperature difference by the expanding and compressing the working fluid. A similar concept of the Stirling cooler could also be adopted to develop a heat pump. Compared to the traditional vaporcompression refrigeration systems, the Stirling coolers are of higher efficiency and with no components like compressor, expansion valve, evaporator, or condensers. Therefore, they are considered to be clean cooling devices. On the other hand, the Stirling engine is an external combustion engine, which is compatible with a variety of thermal sources, such as solar radiation, waste heat, geothermal energy, combustion, and so on. With the heat input to the hot end of the engine, the Stirling engine could be operated to produce mechanical work/electricity at high thermal efficiency. In principle, the Stirling machines are capable to provide all the forms of energy (heat, cool, and electricity) that form the almost total energy load of a building.

AbstractDendronic antennae systems containing pyrene units as energy donors and a styrylpyridinium derivative as energy acceptor show efficient energy transfer from the green‐emitting pyrene excimer to the red‐emitting acceptor. For the third dendron generation the effective screening of the pyrene units on the acceptor provides thin films showing bright red emission. Single‐layer light‐emitting diodes prepared by properly balancing the dendrons and donor units concentration in polyvinylcarbazole show electroluminescence from the blue, green and red components of the monomeric donor, the donor excimer and the acceptor when excitons are generated in the polymer and subsequently transferred to the molecules by resonant energy transfer.

The high power density, ease of transportation and storage and many years of development of internal combustion engine technologies have put liquid hydrocarbon fuels at a privileged position in our energy mix. Therefore processes that use renewable energy sources to produce liquid hydrocarbon fuels from H2O and CO2 are of crucial importance. Concentrated Solar Power (CSP) can be employed as the only energy source for the renewable production of hydrogen from water either indirectly, e.g. by supplying the electricity for electrolysis, or directly by supplying the necessary heat for thermochemically producing hydrogen. Among the various thermochemical cycles tested so far for CSP-driven hydrogen production via water splitting (WS), those based on redox-pair oxide systems, are directly adaptable to carbon dioxide splitting (CDS) and/or combined CO2/H2O splitting for the production of CO or syngas, respectively. The acknowledgement of this fact has recently revived the interest of the scientific community on such technologies. The current article presents the development, evolution and current status of CSP-aided syngas production via such redox-pair-based thermochemical cycles. At first the various redox oxide material compositions tested for water/carbon dioxide splitting are presented and their redox chemistries are discussed. Then the selection of suitable solar reactors is addressed in conjunction with the boundary conditions imposed by the redox systems as well as the heat demands, technical peculiarities and requirements of the cycle steps. The various solar reactor concepts proposed and employed for such reactions and their current status of development are presented. Finally, topics where further work is needed for commercialization of the technology are identified and discussed.

Starting from an interpretation of “sustainable mobility”, this study describes a possible taxonomy of the modalities of urban travels related to sustainability and it suggests an inclusive approach to implement urban policies for “soft mobility” inside the urban contexts. These policies aim at improving the levels of urban liveability, reducing the polluting emissions and promoting the recovery of a sober moral behaviour in acting and reacting inside the city. The underway photovoltaic bikesharing project “Bene Bike” in Benevento shows how the bike station plays an innovative role. It represents a multifunctional element able of managing material and immaterial “flows of urban travels” (people, energy, information).

Abstract Environmental-impact reduction potential is great early in new product development. To exploit this potential, this study evaluates novel combinations of existent processing technologies. Process engineering is combined with an environmental product assessment along the supply chain. In the dairy sector, drying milk into milk powders is a highly energy-intensive process. This study investigates whether switching from milk powders to new products known as milk concentrates diminishes the overall environmental impact along the supply chains of dairy-containing products. A comparative life cycle assessment (LCA) is conducted, which considers individual processing steps that can be combined and operated in various ways to generate a multitude of different skim milk concentrates. For relevant environmental indicators such as cumulative energy demand, global warming potential, eutrophication potential, and acidification potential, concentrates were found to have a lower environmental impact than powders, even if the former are trucked up to 1000 km. This break-even distance is a conservative estimate. It depends upon the environmental impact of raw-milk production. The concentrate with the lowest environmental impact is produced by a combined concentration with reverse osmosis and evaporation to a dry-matter content of 35% and preservation via subsequent pasteurization. This holds for all indicators except eutrophication potential, for which this concentrate is the second-best option. This study identifies the frame within which milk concentrates are an advantageous substitution for milk powder and demonstrates the value of applying environmental assessment to product development and processing-technology selection.

Abstract The feasibility of integrating a commercially available reheat gas turbine with a methane steam reformer is analyzed. A slight modification to the original reheat design is proposed to improve the methane conversion rate in the reforming process and, consequently, the efficiency in recovering waste exhaust heat from the gas turbine. Two solutions are proposed for the heat recovery scheme: a first reformer has a single pressure level while the second has two in order to match the different pressures of the combustors. While the single pressure scheme gives good performance with respect to the stand alone gas turbine, the dual pressure reformer can give a further benefit, as far as an accurate optimization of the steam management is performed.