• Energy Research
• 7. Clean energy close
• US close
• DE close
• BE close

Abstract This paper uses research-quality, ground measurements of irradiance and temperature that are accurate to ±2% to estimate the electric energy yield of fixed solar modules for utility-scale solar power plants at 18 sites in Saudi Arabia. The calculation is performed for a range of tilt and azimuth angles and the orientation that gives the optimum annual energy yield is determined. A detailed analysis is presented for Riyadh including the impact of non-optimal tilt and azimuth angles on annual energy yield. It is also found that energy yield in March and October are higher than in April and September, due to milder operating temperatures of the modules. A similar optimization of tilt and azimuth is performed each month separately. Adjusting the orientation each month increases energy yield by 4.01% compared to the annual optimum, but requires considerable labour cost. Further analysis shows that an increase in energy yield of 3.63% can be obtained by adjusting the orientation at five selected times during the year, thus significantly reducing the labour requirement. The optimal orientation and corresponding energy yield for all 18 sites is combined with a site suitability analysis taking into account climate, topography and proximity to roads, transmission lines and protected areas. Six sites are selected as having high suitability and high energy yield: Albaha, Arar, Hail, Riyadh, Tabuk and Taif. For these cities the optimal tilt is only slightly higher than the latitude, however the optimum azimuth is from 20° to 53° west of south due to an asymmetrical daily irradiance profile.

The need for an improved control strategy for the operation of a wind-powered refrigeration system for the storage of apples was investigated. The results are applicable to other systems which employ intermittently available power sources, battery and thermal storage, and an auxiliary, direct current power supply. Tests were conducted on the wind-powered refrigeration system at the Virginia Polytechnic Institute and State University Horticulture Research Farm in Blacksburg, Virginia. Tests were conducted on the individual components of the system. In situ windmill performance were also conducted. The results of these tests have been presented. An improved control strategy was developed to improve the utilization of available wind energy and to reduce the need for electrical energy from an external source while maintaining an adequate apple storage environment. Ph. D.

As the concern with global warming increases causing the need for CO2 reduction, renewable energy is of great interest as it has lower carbon footprint when compared to conventional sources (natural gas, coal, oil and nuclear). Solar energy has been drawing worldwide attention since it can transform sunlight directly into electricity with the use of photovoltaic (PV) cells. However, this technology has some drawbacks that need to be addressed including dust deposition on solar panels, also known as soiling. Soiling can decrease PV panel's efficiency thereby resulting in less energy production. The soiling rates are very site specific and depend on the geographic location of the panels and the climate in that area. The solar panels can be cleaned naturally (by rainfall, snow or wind) or mechanically washed. This thesis addresses the impact of solar panel soiling and washing on the energy production of solar PV plants located at the UNLV campus. The objectives of this project were (a) to evaluate whether rainfall alone, in the desert environment with low rainfall, is sufficient to clean up the solar panels, and, if possible, determine the minimum amount of rainfall necessary to clean up panels.; (b) to examine the efficiency loss caused by soiling using different methods of analyses and (c) to evaluate if panel washing is worthwhile given the cost and the efficiency gain that is obtained by washing. To calculate the efficiency of the panels, a model was developed to generate parameters that were not measured at the site. Panel efficiencies before and after rainfall events were compared to determine the minimum amount of rain necessary to clean the panels. It was found that at least 0.2 inches of rain was needed to partially restore clean-panel efficiency. In Las Vegas, the recurrence periods of different depths rainfall were calculated using data from the past 29 years. It was observed that the 50th percentile recurrence period of a rainfall event with depth of 0.2 inches or higher was approximately 52 days. Student Union: -0.0044%/day, CBC-C: -0.00099%/day, and Dayton Hall: -0.0034%/day The amount of efficiency lost during the dry intervals (periods between rainfall events) was analyzed in three different ways. The average efficiency loss per day during the dry periods varied from -0.000171 % to -0.00533 %, depending on the method used and the building where the panels were located. However, there were some limitations to the calculations. It was not possible to completely isolate the effects of only soiling on the efficiency of the panels. The rate of decline seemed to be also impacted by seasonal effects. To better evaluate the effect of washing, a professional company was hired to wash a set of solar panels located on UNLV's Student Union building. The panels were washed with water with a low concentration of TDS. The power output and the efficiency of those panels were analyzed from before and after the washing. There was a very small efficiency and power increase due to the washing. Therefore, it was concluded that washing in this area is not worthwhile, and that rainfall events in excess of 0.2 inches can adequately restore the efficiency of the panels. If there is a change in cost of energy, washing, water or a great increase in the efficiency of the solar panels, it would be necessary to reevaluate the analysis.

Abstract Building energy performance is often inadequate given design goals. While different types of assessment methods exist, they either do not consider design goals and/or are not general enough to integrate new and innovative energy concepts. Furthermore, existing assessment methods focus mostly on the building and system level while ignoring more detailed data. With the availability and affordability of more detailed measured data, the increased number of measured data points requires a structure to organize these data. This paper presents the Energy Performance Comparison Methodology (EPCM), which enables the identification of performance problems based on a comparison of measured data and simulated data representing design goals. The EPCM is based on an interlinked building object hierarchy that structures the detailed performance data from a spatial and mechanical perspective. This research is developed and tested on multiple case studies that provide real-life context and more generality compared to single case studies.

Abstract Adsorbent-based carbon capture is only feasible if adsorption-desorption cycles are both fully regenerating and efficient. This work proposes a regenerative pH swing process and a pH swing regenerative adsorbent that are inspired by natural CO2 conversion by carbonic anhydrase biocatalysts found in mammalian red blood cells. The main objective is to develop, test and analyze a synthetic pH Swing Adsorption (pHSA) system as well as a pHSA compatible solid adsorbent to capture CO2 from a simulated ambient air gas stream. The lead developed adsorbent is a carbon black co-activated with potassium carbonate and nitrogenous copolymer that is impregnated with immobilized bovine carbonic anhydrase and thereby deemed “BCA/KN-CB”. BCA/KN-CB has preliminarily demonstrated both competitive CO2 adsorption capacity and limited regenerative ability under experimental pHSA conditions. In addition, BCA-based adsorbents achieved higher adsorption capacities than non-BCA adsorbent counterparts. The BCA/KN-CB adsorbent displayed both large point of zero charge (PZC) swings and regenerative stability. The proposed pHSA system requires essentially zero energy expenditure to achieve intended environments for capture and regeneration. With 1 kg of adsorbent, pHSA has the ability to capture 1 kg CO2 in less than 4 h of cycling. The tested pHSA adsorbent can also capture more than 96% of total CO2 in a given raw gas stream flowing through the capture chamber. This proof-of-concept study of a pH swing adsorption/biocatalytic adsorbent system suggests the potential to effectively operate under ambient conditions and exhibit advantageous operational efficiencies to other high-profile CO2 capture systems.

The coupling of water-splitting catalysts to silicon photovoltaics enables direct solar-to-fuel conversion. Critical to the performance of such devices is the use of interfaces to protect silicon from the oxygen-evolving reaction (OER) and at the same time to provide Ohmic contact between the buried silicon junction and the immobilised OER catalyst. Presented herein are guidelines for constructing the Si|catalyst interface, which is a crucial building block for efficient direct solar-to-fuel conversion devices. We show that fluorinated-tin-oxide is an especially attractive interface for buried-junction devices.

Abstract With promising benefits such as traffic emission reduction, traffic congestion alleviation, and parking problem solving, Electric Vehicle (EV)-sharing systems have attracted large attentions in recent years. Different from other business modes, customers in sharing economy systems are usually price sensitive. Therefore, it is possible to shift the usage of shared EVs through a well-designed Dynamic Pricing Scheme (DPS), with the objective of maximizing the system operator's total profit. In this study, we propose a novel DPS for a large-scale EV-sharing network to address the EV unbalancing issue and satisfy the vehicle-grid-integration (VGI) service based on accurate station-level demand prediction. The proposed DPS is formulated as a complex optimization problem, which includes two Price Adjustment Level (PAL) decision variables for every origin-destination pair of stations. The two PALs are employed to affect the EV-sharing demand and travel time between each station pair, respectively. Physical and operational constraints from both EV demand and VGI service aspects are also included in the proposed model. Two case study are conducted to validate the effectiveness of the proposed method.

Abstract The combination of biomass gasification with fuel cells, especially high temperature Solid Oxide Fuel Cells (SOFCs) promises sustainable and highly efficient (decentralized and modular) energy conversion systems. This review encompasses the components of biomass integrated gasification–SOFC technology including biomass characteristics, the thermochemical conversion in gasifiers and the factors affecting the gasification process, the cleaning technologies for raw producer gas and its conditioning and finally the integration of gasifier with SOFCs. The influence of impurities present in biomass producer gas such as particulates, tar, H 2 S, HCl and alkali compounds based on recent experimental studies and their tolerance limits towards SOFCs are presented. Even though analysis based on the probable tolerance limits of impurities towards SOFCs and a comprehensive overview of the cleaning technologies for producer gas impurities indicate that producer gas cleaning at various temperatures using current technologies to meet SOFC requirements is possible, more experimental studies are still needed to acquire the detailed information on the tolerance limits of impurities for SOFCs. The recent theoretical modeling and experimental studies of biomass integrated gasification–SOFC systems are also presented.

Abstract This paper investigates the performance of a variable ratio gearbox (VRG) used in a small fixed-speed wind turbine with active blades. The major components of the VRG-enabled drivetrain are an automatic-manual gearbox and squirrel cage induction generator that connects directly to the grid. The simplicity of this system may be appealing for applications when cost and reliability are of concern. It is an alternative to variable speed systems, which necessitate a modified generator and power conditioning equipment. During partial load operation the VRG provides a discrete set of rotor speeds. This allows the controller to track the wind speed and to achieve a greater efficiency. This study suggests three VRG ratios are sufficient to improve performance when used with active blades. A case study is presented where the performance is simulated using three different wind data sets. The study suggests that the VRG can improve production between 7 and 8.5% in low wind areas. The design procedure also illustrates a technique for finding the lowest and highest gear ratios needed for VRG design. These ratios allow the system to achieve the lowest cut-in and rated speeds. The approach also has useful implications for the design of a continuously variable transmission.