• Energy Research
• Closed Access close
• Open Source close
• Embargo close
• CA close
• EU close

Herewith we present the extended 1Hz dataset of wind measurements from a Skipheia meteorological station on the island of Frøya on the western coast of Norway, Trondelag. The data binned in 10 min averages can be find at: https://doi.org/10.5281/zenodo.2557500 The site represents an exposed coastal wind climate with open sea, land and mixed fetch from various directions. UTM-coordinates of the Met-mast: 8.34251 E and 63.66638 N. See the map for details (NorwegianMapping Authority): https://www.norgeskart.no/#!?project=norgeskart&layers=1003&zoom=3&lat=7035885.49&lon=539601.41&markerLat=7077031.483032227&markerLon=170902.83203125&panel=searchOptionsPanel&sok=Titranveien Presented data were gathered between years 2009-2016. Data&hardware summary: Years 2009-2016: Mast2 equipped with 6 pairs of 2D sonic anemometers at 10, 16, 25, 40, 70, 100 m above the ground, independent temperature measurements at the same heights and near the ground; pressure and relative humidity from local meteostation (Sula, 20 km away). Years 2014-2016: Mast4 equipped with 2 pairs of 2D sonic anemometers at 40 and 100 m above the ground. The distance between the masts is 79 m. Data is binned in years and months and stored in a ‘*.txt’ tab-separated values file. Data column order is described in SkipheiaMast2_header.txt and SkipheiaMast4_header.txt, where WSx is the wind speed (m/s), WDx is the wind direction (360 deg), ATx is the air temperature (deg C) and x designates the instrument number. The instruments are numbered starting from the ground. Example: For Mast2 (6 pairs of anemometers, ground temperature + 6 temperature sensors on the mast) that means that AT0 is the ground temperature. WS1 and WS2 are wind speed records at 10 m level. WS3 and WS4 are wind speed records at 16 m. For Mast4 (2 pairs of anemometers) that means that WS1 and WS2 are wind speed records at 40 m level. WS3 and WS4 are wind speed records at 100 m. Detailed site description with wind climate description can be found in attached analysis: Site analysys.pdf. Additional information and analysis can be found in listed below works, using data from Frøya site: Bardal, L. M., & Sætran, L. R. (2016, September). Spatial correlation of atmospheric wind at scales relevant for large scale wind turbines. In Journal of Physics: Conference Series (Vol. 753, No. 3, p. 032033). IOP Publishing, doi:10.1088/1742-6596/753/3/032033, https://iopscience.iop.org/article/10.1088/1742-6596/753/3/032033/pdf Bardal, L. M., & Sætran, L. R. (2016). Wind gust factors in a coastal wind climate. Energy Procedia, 94, 417-424, https://doi.org/10.1016/j.egypro.2016.09.207 IEA Wind TCP Task 27 Compendium of IEA Wind TCP Task 27 Case Studies, Technical Report, Prepared by Ignacio Cruz Cruz, CIEMAT, Spain Trudy Forsyth, WAT, United States, October 2018; Chapter 1.8. https://community.ieawind.org/HigherLogic/System/DownloadDocumentFile.ashx?DocumentFileKey=8afc06ec-bb68-0be8-8481-6622e9e95ae7&forceDialog=0 Domagalski, P., Bardal, L. M., & Sætran, L. Vertical Wind Profiles in Non-neutral Conditions-Comparison of Models and Measurements from Froya. Journal of Offshore Mechanics and Arctic Engineering, doi: 10.1115/1.4041816, http://offshoremechanics.asmedigitalcollection.asme.org/article.aspx?articleid=2711333&resultClick=3 Møller, M., Domagalski, P., & Sætran, L. R. (2019, October). Characteristics of abnormal vertical wind profiles at a coastal site. In Journal of Physics: Conference Series (Vol. 1356, No. 1, p. 012030). IOP Publishing. https://iopscience.iop.org/article/10.1088/1742-6596/1356/1/012030 Møller, M., Domagalski, P., and Sætran, L. R.: Comparing Abnormalities in Onshore and Offshore Vertical Wind Profiles, Wind Energ. Sci. Discuss., https://doi.org/10.5194/wes-2019-40 , in review, 2019.

Abstract In this study, crude cellulose derived from cornstalk, after bleaching, was used as raw material for the synthesis of sodium carboxymethyl cellulose (CMC) by reacting with the cellulose with NaOH and chloroacetic acid at 75 °C for 1.5 h. Effects of alkali dosage, concentration of chloroacetic acid on the physical and chemical properties of the CMC products were investigated. It was revealed that the reactants alkali reagent/chloroacetic acid/cellulose at the molar ratio of 4.6:2.8:1and 4:2.5:1, or at the molar ratio of NaOH/ClCH 2 COOH ≈1.6–1.64, resulted in CMC products of relatively high water solubility. The viscosity-average molecular weight M v of these two CMC products obtained at molar ratios of 4.0:2.5:1 and 4.6:2.8:1 is in the range of 1.94 × 10 4 –2.48 × 10 4 g mol −1 , and the average DS of the two products are 0.57 and 0.85, respectively. As the solute concentration is above 2 wt%, the viscosity of the CMC-water solution exhibits nonlinear (exponential) increasing with increasing the solute concentration (typical of non-Newton fluids).

A detailed analysis of the effects of ground grid configuration on grounding performance has been carried out for uniform and horizontally stratified soils with multiple layers. The results of the analysis reveal that the most efficient and cost-effective design is highly dependent on soil structure type and characteristics. In the absence of ground rods, grounding grids with uniform mesh size are quite efficient in soils having a thin (relative to grid size) high resistivity (relative to the lower layers) top soil, while grids with small mesh size at the periphery of the grid provide optimum performance in uniform soils and soils with low resistivity top soils. Ground rods were found to be effective only when a significant portion of their length is in contact with a low resistivity soil, as expected.

Experiments were carried out to determine the accuracy and validity of estimations of hepatic blood flow from systemic clearances of ethanol during very low dose (8 μmol∙min−1∙kg−1) infusions of ethanol in anesthetized cats. Systemic clearances were compared with directly measured hepatic blood flow using a hepatic venous long-circuit technique. This technique allowed direct measurement and alteration of hepatic blood flow and collection of arterial, portal, and hepatic venous blood samples without depletion of the animal's blood volume. In 18 cats, Vmax for ethanol was 93 ± 7 μmol∙min−1 per 100 g liver or 21 ± 2 μmol∙min−1∙kg·body weight−1 and Km was 144 ± 19 μM in terms of logarithmic mean sinusoidal concentration. At the dose of 8 μmol∙min−1∙kg body weight−1 used for estimation of hepatic blood flow, extraction was 0.95 ± 0.07 (mean ± SD). Systemic clearance of ethanol overestimated directly measured hepatic blood flow by 15 ± 16%. Hepatic blood flow changes expressed as percentages of the control level were accurately estimated from systemic ethanol clearance (100 ± 10%). Since 73 ± 12% of the infused ethanol was eliminated by the liver and 83 ± 11% was eliminated by the splanchnic bed, an extrasplanchnic uptake of 17% accounted for the overestimation of hepatic blood flow. Estimation of hepatic blood flow from systemic clearances of ethanol during very low dose infusions may have advantages over other clearance methods. Its use in cats was illustrated in a separate series of experiments and it was shown that surgery significantly reduced hepatic blood flow. The method may merit trial for estimation of hepatic blood flow in humans.

Abstract Thermal performance of three naturally ventilated public buildings in which the wind tower is an important architectural freature is studied. One of the three builidings as well as it's wind tower is instrumented for temperature, relative humidity and airflow velocity measurements, and the other two are instrumented for temperature measurement. The results have led to a discussion concerning the degree of wind tower effectiveness in achieving thermal comfort.

Abstract Bio-based polyurethane (BPU) foams were successfully prepared using hydrothermally liquefied wheat straw (WS) to substitute a mass fraction of up to 50% of polyols. Response surface methodology (RSM) based on central composite design (CCD) was employed to optimize four process parameters: NCO/OH molar ratio, loading of crosslinking agent (glycerol), loading of catalyst (a mixture of triethylene diamine, stannous octoate, and triethanolamine), and loading of blowing agent (water) for the maximum compression strength of the rigid BPU foams. With the quadratic orthogonal regression model, verified by experimentation, the maximum compression strength of approximately 180 kPa was obtained at the following optimal conditions: NCO/OH molar ratio of 1.24:1, glycerol addition of 12.11%, catalyst loading of 0.76%, and blowing agent addition of 1.31% in relation to the total mass of polyols. The BPU foam prepared at the optimal conditions exhibits good thermal conductivity (0.045 Wm−1K−1) and thermal stability, comparable to those of a reference foam prepared with 100% PPG400.

AbstractThe presented synthesis of the title compounds (II), (IV), (VI) and (VIII) is extremely simple and highly efficient without the use of any chromatographic purification.

Abstract The influence of the solid-phase wall boundary condition was investigated in Eulerian–Eulerian numerical simulations of a bubbling fluidized bed. Parametric studies of the particle–wall restitution coefficient and specularity coefficient were performed to evaluate their impact on the predicted flow hydrodynamics in terms of bed expansion, local voidage, and solid velocity. Both two- and three-dimensional simulations were conducted and compared with available experimental data on solid velocity and bubble properties. It is found that the wall effect plays an important role in CFD models. Such factors as the voidage at the bubble boundary, averaging method, and minimum bubble size also influence the mean bubble diameter.