• Energy Research
• Closed Access close
• engineering and technology close
• US close
• GB close
• CA close

Abstract In this study, crude cellulose derived from cornstalk, after bleaching, was used as raw material for the synthesis of sodium carboxymethyl cellulose (CMC) by reacting with the cellulose with NaOH and chloroacetic acid at 75 °C for 1.5 h. Effects of alkali dosage, concentration of chloroacetic acid on the physical and chemical properties of the CMC products were investigated. It was revealed that the reactants alkali reagent/chloroacetic acid/cellulose at the molar ratio of 4.6:2.8:1and 4:2.5:1, or at the molar ratio of NaOH/ClCH 2 COOH ≈1.6–1.64, resulted in CMC products of relatively high water solubility. The viscosity-average molecular weight M v of these two CMC products obtained at molar ratios of 4.0:2.5:1 and 4.6:2.8:1 is in the range of 1.94 × 10 4 –2.48 × 10 4 g mol −1 , and the average DS of the two products are 0.57 and 0.85, respectively. As the solute concentration is above 2 wt%, the viscosity of the CMC-water solution exhibits nonlinear (exponential) increasing with increasing the solute concentration (typical of non-Newton fluids).

A method is presented for calculating the electromagnetic forces on the end windings of turbine generators for both the steady state and transient modes of operation. Part 1 of this paper deals with the basic concepts of the force calculation and gives several examples of steady state forces and how they vary with load and power factor. PartII deals with several types of transient operation. The currents and fields which these transients produce are discussed and forces are found for various cases such as short circuits, synchronizing out of phase and transmission line switching.

Interest in the highly efficient energy hub (EH) model has been growing despite the high computational requirements of planning for a multi-energy, multi-device operation. To address both the device size limitation and the multi-scenario issue, we propose a new solution methodology for solving the EH planning problem. In the method, the decision variables are device sizes. First, a dimension reduction technique is proposed to address the curse of dimensionality based on the correlation of unknown variables such as the capacities of different devices in an EH. Second, to avoid local convergence, a solution method called the variable-sized unimodal searching (VUS) approach is proposed to assure a global optimal planning scheme for the one-dimensional non-convex optimization model obtained from the preceding dimension reduction process. The case study indicates that the proposed approach has a higher computing efficiency than the Benders decomposition (BD) algorithm to deal with a scenario-based stochastic planning problem with a large number of scenarios. Thus, the effectiveness of the EH planning approach is verified.

Abstract This study sought to quantify and characterize cassava waste as fuel. The wastes from three cultivars were collected to study and were divided into three distinct parts of the cassava plant: seed stem, thick stalks, and thin stalks. Physical and chemical analyzes were carried out to determine the elemental composition of the waste: volatile matter; fixed carbon; ash; moisture; lignin; cellulose; hemicellulose; ash composition and higher heating value were determined. We conducted a thermogravimetric analysis in oxidizing and inert atmospheres to study the behavior of the waste as fuel. The root productivity obtained ranged from 7.7 to 13.0 t ha−1 yr−1 on a dry basis (db), and the ratio between waste and roots varied from 0.36 to 0.91. The physical and chemical properties of cassava waste are analogous to those of woody biomass regarding the elemental composition, the higher heating value, and thermogravimetric analysis. Ash content varied from 2.5% to 3.5%, reaching around 6.0% in samples unwashed. Approximately 60% of the ashes are alkali oxides, especially P2O5, K2O, and CaO, which have low melting points. The alkali index calculated suggests that there is a strong tendency that the combustion process leads to ash fouling and the formation of ash deposits.

Abstract Microorganisms used in syngas fermentation require nutrients to grow and convert syngas (CO, H2 and CO2) into various products. Many of the essential nutrients can be provided by biochar. Poultry litter biochar (PLBC) contains minerals and trace metals and has a high pH buffering capacity, making it suitable as a nutrient supplement. The effects of PLBC loadings from 1 to 20 g L−1 on syngas fermentation were determined in 250 ml bottle assays. Results showed that 10 and 20 g L−1 PLBC significantly increased ethanol production compared to standard yeast extract (YE) medium. Fermentations in a 3L continuous stirred tank reactor (CSTR) with 10 g L−1 PLBC with and without 4-morpholineethanesulfonic acid (MES) showed 64% and 36% more ethanol production, respectively, than standard medium. The acetic acid accumulated at the beginning of fermentation was completely converted to ethanol in all media tested in the CSTR. These results demonstrate the feasibility of using PLBC medium without costly MES in the CSTR to enhance ethanol production from syngas for potential use at commercial scale.

Ancillary services and other interconnected services are important especially in a competitive operation environment. Since these services are costs related, they should be allocated in order to send the correct price signal to market participants. An average sensitivity method is proposed for allocating services to simultaneous transactions. It can provide results close to power flow-based methods, while requiring as little computational time as traditional sensitivity-based approaches. Except for rare cases, it satisfies the requirement of allocation quantity, allocation ratio, and application feasibility. Test results indicate that the average sensitivity method is a successful allocation algorithm.

The paper comprises a systematic experimental investigation into the influence of AC test source parameters on the leakage current pulses, voltage fluctuations and flashover voltages of polluted insulators. The test techniques include both salt-and clean-fog methods, while the test insulators comprise long-rod and cap and pin strings of different lengths as well as support columns.

A detailed analysis of the effects of ground grid configuration on grounding performance has been carried out for uniform and horizontally stratified soils with multiple layers. The results of the analysis reveal that the most efficient and cost-effective design is highly dependent on soil structure type and characteristics. In the absence of ground rods, grounding grids with uniform mesh size are quite efficient in soils having a thin (relative to grid size) high resistivity (relative to the lower layers) top soil, while grids with small mesh size at the periphery of the grid provide optimum performance in uniform soils and soils with low resistivity top soils. Ground rods were found to be effective only when a significant portion of their length is in contact with a low resistivity soil, as expected.

A mathematical model of the LiAl/LiCl, KCl/FeS cell has been used to study the behavior of the system during relaxation and charging. The effects of state of charge, cell temperature, and current density are presented, and the influence of a period of relaxation on the subsequent charging operation is investigated. In addition, factors that can have a significant impact on the charging characteristics are identified.