• Energy Research
• Closed Access close
• Open Source close
• 12. Responsible consumption close
• 11. Sustainability close
• IN close
• CA close
• JP close
• UA close

The current status and challenges associated with the production and utilization of cellulosic ethanol in Korea are reviewed in this paper. Cellulosic ethanol has emerged as a promising option for mitigating Korea's CO(2) emissions and enhancing its energy security. Korea's limited biomass resources is the most critical barrier to achieving its implementation targets for cellulosic ethanol. Efforts to identify new suitable biomass resources for cellulosic ethanol production are ongoing and intensive. Aquatic biomasses including macroalgae and plantation wastes collected in the Southeast Asia region have been found to have great potential as feedstocks for the production of cellulosic ethanol. R&D explorations into the development of technologies that can convert biomass materials to ethanol more efficiently also are underway. It is expected that cellulosic ethanol will be in supply from 2020 and that, by 2030, its use will have effectively reduced Korea's total gasoline consumption by 10%.

This paper presents a multi-objective optimization model for a long-term generation mix in Indonesia. The objective of this work is to assess the economic, environment, and adequacy of local energy sources. The model includes two competing objective functions to seek the lowest cost of generation and the lowest CO2 emissions while considering technology diffusion. The scenarios include the use of fossil reserves with or without the constraints of the reserve to production ratio and exports. The results indicate that Indonesia should develop all renewable energy and requires imported coal and natural gas. If all fossil resources were upgraded to reserves, electricity demand in 2050 could be met by domestic energy sources. The maximum share of renewable energy that can be achieved in 2050 is 33% with and 80% without technology diffusion. The least cost optimization produces lower generation costs than the least CO2 emissions, as well as the combined scenario. Total CO2 emissions in 2050 are five to six times as large as current emissions. The least CO2 emissions scenario can reduce almost half of the CO2 emissions of the least cost scenario by 2050. The proposed multi-objective optimization model leads some optimal solutions for a more sustainable electricity system.

Yard waste is either dumped or is being openly burned to get rid of it, instead of using it as a valuable renewable energy source. In this study, hydrothermal carbonization of yard waste was conducted to valorize it as a solid bio fuel, using a batch reactor. The effect of process parameter on yield, energy and physicochemical properties of the valorized solid bio fuel (hydrochar) was examined in this study by varying reaction temperature (160-200 °C for 2 h) and reaction time (2-24 h at 200 °C). The calorific value of hydrochar was within a range of 17.72-24.59 MJ/kg as compared to 15.37 MJ/kg for untreated yard waste. Hydrochar mass yield decreased from 78.6% at operating temperature - time of 160 °C -2 h to 45.6% at 200 °C -24 h. The plot of atomic ratios (H/C and O/C) demonstrates improvement in the coalification process which was mainly governed by decarboxylation and dehydration reactions. The grindability of the prepared hydrochar was comparable to that of coal. Hydrochar produced at lower reaction condition (160-200 °C at 2 h) have better flowability as compared to that produced at higher reaction condition (4-24 h at 200 °C). The reaction time longer than 12 h has a minimal effect on the yield, energy and physicochemical properties of hydrochar. Increasing reaction time and temperature improved the ignition and burnt temperature of hydrochar. All reaction condition has an energy ratio (energy output to energy input) of more than one making HTC process a net energy producer.

Abstract Light wells in the centers of high-rise apartment buildings in Japan are called ‘Voids’. Gas water-heaters built into Voids discharge exhaust gas so a large enough opening has to be designed at the bottom of a Void to keep the indoor air quality (IAQ) acceptable. In order to secure the IAQ in the Void from contamination, a simple calculation method of the ventilation rate induced by wind force and thermal buoyancy through openings at the bottom, along with heat sources such as water-heaters, is presented. The accuracy of this calculation method was examined by wind tunnel testing. As a result, it turned out that the simple calculation methods introduced in this study were valid for predicting the vertical temperature distribution and ventilation rates in Voids.

Biogas is a viable alternative for supplying clean and sustainable energy. Despite all manner of policy measures introduced by the Government of India, biogas is not widely used in India. This article tries to identify factors that influence the decision to adopt biogas at household level. We examine a conceptual framework empirically in which a household wants to maximize utility from biogas by using the India Human Development Survey (IHDS) I, which is a nationally representative, multi-topic survey. By applying both maximum likelihood and penalized likelihood methods (Firthlogit) of logistic regression on a sample size of almost 10,384 households, it has been found that wealthy people are more likely to adopt biogas compared to the marginalized section of the society. We recommend more inclusive policy measures for the weaker section of the society to create an enabling environment to make it a self-promoting technology.

This paper presents experimental results of the impact of CO(2) co-feed on a gasification/pyrolysis process for various feedstocks (biomass, coal, and municipal solid waste (MSW)). Various feedstocks were thermo-gravimetrically characterized under various atmospheric conditions and heating rates. A substantial amount of char burn out was identified in the presence of CO(2) via a series of thermo-gravimetric analysis tests, which enabled high conversion of final mass (approximately 99%) to be achieved. The impact of CO(2) co-feed on the volatilization regime during the pyrolysis/gasification process was not apparent at a heating rate of 10-40 degrees C min(-1). However, the impact of CO(2) on the volatilization regime at a fast heating rate (950 degrees C min(-1)) was substantial. For example, significant enhancement in the generation of CO, by a factor of approximately 2, was observed in the presence of CO(2). The generation of major chemical species, such as CH(4) and C(2)H(4), were enhanced, but this was not as apparent as in the case with CO. In addition, introducing CO(2) to the pyrolysis/gasification process enabled the amount of condensable liquid hydrocarbons, such as tar (approximately 30-40%) to be significantly reduced in the presence of CO(2), in that injecting CO(2) into the pyrolysis/gasification process expedites cracking the volatilized chemical species. Experimental work confirmed that biomass and MSW could be feasible and desirable feedstocks for the pyrolysis/gasification process as these feedstocks can be easily treated compared to coal. To extend this understanding to a more practical level, various feedstocks were tested in a tubular reactor and drop tube reactor under various experimental conditions.

Anode with good electrocatalytic capabilities is more specifically required to reduce the ohimic losses during microbial fuel cell (MFC) operation. Highly conductive polymers viz., Polyaniline (PANi) and Polyaniline/Carbon nanotube (PANi/CNT) composite were prepared by in situ oxidative chemical polymerization method. Anodes were fabricated independently by coating PANi and CNT/PANi composites on the surface of SSM. The fabricated electrodes were evaluated as anode against stainless steel mess (SSM) as cathode during MFC operation. Maximum bioelectricity generation was observed in SSM-PANi/CNT-anode with power density of 48 mW/m2 and COD removal efficiency of 80% compared with SSM-PANi-anode (38 mW/m2; 65%) and SSM-anode (28 mW/m2; 58%). Bioelectrochemical characterization of the electrode materials using cyclic voltammetry and electrochemical impedance spectroscopy showed high electrocatalytic activity of PANi/CNT composite electrode. The study concluded the efficiency of PANi/CNT composite electrodes as bioanode in operation of MFCs towards achieving increased bioelectricity production along with wastewater treatment.

Abstract Biodiesel has gained the forefront of our focus on renewable transportation fuels. This article provides a comprehensive review on the sources used as feedstock and their classification based on generation or type (edible, non-edible, waste resources and animal fats) along with a variety of classical and modern oil extraction techniques. The technical aspects of the various biodiesel production methods currently implemented to the best of our knowledge are discussed here, which include in-situ biodiesel production, both catalysed (homogeneous and heterogeneous systems) and uncatalysed classical production approaches, with emphasis on how each of these approaches are affected by their reaction parameters. The review also highlights the observed drawbacks of each process with a view to assessing the implementation of supercritical and superheated technologies as an alternative, economically feasible advancement. Supercritical process (SCP) has shown great prospect in the obtainment of high quality biodiesel from a wide range of high to low grade feedstock with minimal impacts on the presence of water or FFAs (free fatty acids). From available literature it is shown that these do not affect the process significantly, and various other supercritical fluids such as methyl acetate, tert-butyl methyl ether (MTBE) and dimethyl carbonate can also be used to avoid glycerol formation. The process however, suffers from high initial implementation cost being the most prominent drawback, among others like thermal degradation of the fuel. Another promising technique, the superheated vapour technology (SHV) has emerged as an alternative, with limited literature proving the superiority of either of these processes to be inconclusive. In future works, researchers need to look into various aspects such as developing a spiral reactor for heat recovery, using software based optimization for eliminating redundant experiments analysing production cost for industrial scale-up and improving the fuel’s oxidative stability by adding antioxidants for convenient long-term storage and use.

Abstract Recharging infrastructure (RI) deployment plays a vital role in improving the public recharging availability for transport electrification. Decarbonizing transportation using low-emission electricity requires massive RI network. Even though the consumers are reluctant to purchase electric vehicles (EVs) until RIs are sufficiently placed, the investors are not willing to invest in RIs due to recharging demand uncertainties. Therefore, a scientific planning framework is needed to ensure the sustainable deployment of EV-RIs in complex networks. In this study, a lifecycle thinking-based multi-period infrastructure-planning framework is proposed to develop sustainable public EV-RIs in an urban context. This framework consists of a temporal model to find the dynamic EV-RI demands, a stochastic model to obtain travel distances, and a multi-objective optimization model to select the best desirable capacities and locations for potential EV-RIs. A case study of a typical medium-scale municipality in Canada was assessed using the proposed framework and validated using conventional infrastructure planning scenarios. The geo-processing data, regional travel behaviors, and recharging characteristics were used as model inputs. The results of the case study showed that the proposed framework can be used to estimate multi-period public recharging demands, minimize lifecycle costs, maximize service coverage and infrastructure utilization, and ensure reasonable paybacks compared to conventional planning approaches. Moreover, this framework can be used to compare different investment assistances, which are required in the early stages of the RI deployment process to encourage investors. Furthermore, government and private institutions can use this framework to identify recharging demands, permitting, and developing RIs in the long-run.