• Energy Research
• Restricted close
• Open Source close
• 12. Responsible consumption close
• 6. Clean water close
• CA close

Hot water heat stores with stratification are a common technology used in solar energy systems and reuse of waste heat. Adding a PCM module at the top of the water tank would give the system higher storage density, and compensate heat loss in the top layer. The work presented here includes experimental results and numerical simulation of the system using an explicit finite-difference method. Experiments and simulations were carried out using different cylindrical PCM modules. With only 1/16 of the volume of the store being PCM, 3/16 of water at the top of the store was held warm for 50% to 200% longer and the average energy density was increased by 20% to 45%. Furthermore, these 3/16 of water were reheated by the heat from the module after being cooled down in only 20 min.

Abstract In recent years, the overall energy consumption is increasing significantly and the energy consumption in the building sector represents over 30% of the global ones in developed countries. Thermal energy storage (TES) using phase change materials (PCM), which are materials able to store high amounts of energy as latent heat, is suggested as a possible solution to decrease the energy consumption. The authors of this paper developed materials able to encapsulate/stabilize PCM in addition to isolate an industrial residue from the steel recycling process: electrical arc furnace dust (EAFD). This waste is a hazardous dust, and when it is combined with a polymeric matrix produce dense sheet materials suitable for multilayered constructive systems. In this paper the physical, mechanical, thermal and acoustical characterization of two new materials with EAFD and PCM in a polymeric matrix for constructive system is presented. The results are compared with those obtained for one commercial dense sheet material available in the market, Texsound commercialized by TEXSA (Spain). The new dense sheet materials developed in this paper have similar acoustic properties compared to the results obtained for the commercial material and are competitive with it, even better because the new material incorporates PCM which increases the thermal inertia of final constructive system.

Using recycled rubber crumbs as drainage layer in extensive green roofs have high potential to reduce the heating and cooling loads in buildings over traditional materials used as drainage layer, such as pozzolana gravel. However, the environmental impact due to the life cycle should be analyzed to assess its environmental benefit. This paper evaluates the environmental performance of green roofs in which the drainage layer is made of rubber crumbs, a recycled material the use of which is still experimental for this purpose. In this paper Life Cycle Assessment (LCA) is applied to compare the environmental impact of four constructive systems, two extensive green roofs without insulation layer and with different drainage materials, e a recycled material, rubber crumbs, and a conventional one, pozzolana gravel -, in front of two conventional flat roofs, with and without thermal insulation (polyurethane), built in an experimental set-up consisting of four monitored house-like cubicles, located in Mediterranean continental climate (Lleida, Spain). The LCA considered the production, construction, operational, and disposal phases of the roofs, according to UNE-EN 15643-2. The operational phase was carried out using data measured in the experimental set-up, considering heating and cooling energy consumptions in the winter and summer period, respectively.

Abstract This review summarizes and organizes the literature on life cycle assessment (LCA), life cycle energy analysis (LCEA) and life cycle cost analysis (LCCA) studies carried out for environmental evaluation of buildings and building related industry and sector (including construction products, construction systems, buildings, and civil engineering constructions). The review shows that most LCA and LCEA are carried out in what is shown as “exemplary buildings”, that is, buildings that have been designed and constructed as low energy buildings, but there are very few studies on “traditional buildings”, that is, buildings such as those mostly found in our cities. Similarly, most studies are carried out in urban areas, while rural areas are not well represented in the literature. Finally, studies are not equally distributed around the world.

Low temperature sensitive products transport and storage is an issue worldwide due to changes of the lifestyle population increase. Thermal energy storage (TES) is nowadays one of the most feasible solutions in facing the challenge of achieving energy savings. Many researchers have investigated energy efficiency of different cold units by applying TES systems using phase change materials (PCM). This paper provides an overview of the existing Spanish and European potential energy savings and CO2 mitigation by incorporating TES systems to cold storage and transportation systems. Data on energy savings were compiled from different case studies. Results depend on the scenarios studied and the extent of TES systems implementation; in the case of Europe for instance, yearly CO2 emissions may be cut down between 5% and 22% in reference to 2008 CO2 emissions from cold production considering that the proposed implementation of PCM TES in the case studies found in the literature is done.

Abstract A heat pump coupled to thermal energy storage (TES) tanks is experimentally tested under simulated summer conditions and the results are presented in this paper. The cold TES tank is used for shifting the cooling load of a small house-like structure. The study evaluates the thermal behaviour of the TES tank for cold storage and the application of the system for space cooling. For the analysis, two different configurations of the tanks are compared: a water tank and a PCM tank. The PCM tank is filled with a commercial macro-encapsulated PCM, which has a phase change temperature of 10 °C. The results point out that the PCM tank is able to supply 14.5% more cold and to maintain the indoor temperature within comfort 20.65% longer than the water tank. However, it needs 4.55 times longer to charge the tank.

Abstract Life Cycle Assessment (LCA) has been conducted for seven experimental cubicles located in Puigverd de Lleida (Spain). The objective of this experimental set-up is to test different constructive solutions in order to point out the most sustainable solution with lower energy demand during the operational phase. Therefore, different building, insulation and Phase Change Materials (PCMs) have been tested under controlled temperature conditions to examine the thermal performance of the whole system. Although some of these materials are able to reduce the energy demand and consequently the environmental impact during the operational phase, they still have high embodied energy that can cause high environmental impact during the manufacturing phase. Therefore the LCA study in this paper focuses on assessing the impact of the embodied energy needed during the manufacturing and disposal phase by highlighting and comparing the effect of using different building materials, insulating materials, and phase change materials.

Central solar heating plants with seasonal storage (CSHPSS) are among the most promising technologies to save energy in the industrial and residential-commercial building sectors. This work introduces a systematic approach to optimize these systems according to economic and environmental criteria. Our method, which combines the TRNSYS 17 simulation software with life cycle assessment and multi-objective optimization, identifies optimal CSHPSS designs for any climatic condition and heating demand profile considering economic and environmental criteria simultaneously. The capabilities of this approach are illustrated through its application to a case study of a CSHPSS located in Barcelona (Spain), which satisfies a heating demand for a neighborhood of 1120 dwellings. Numerical results show that the CSHPSS plant leads to significant environmental and economic improvements compared to the use of a conventional natural gas heating system. Our tool can guide engineers and architects in the transition towards a more sustainable residential sector.