• Energy Research
• Closed Access close
• Open Source close
• natural sciences close
• US close
• CN close
• CA close

Abstract In this study, crude cellulose derived from cornstalk, after bleaching, was used as raw material for the synthesis of sodium carboxymethyl cellulose (CMC) by reacting with the cellulose with NaOH and chloroacetic acid at 75 °C for 1.5 h. Effects of alkali dosage, concentration of chloroacetic acid on the physical and chemical properties of the CMC products were investigated. It was revealed that the reactants alkali reagent/chloroacetic acid/cellulose at the molar ratio of 4.6:2.8:1and 4:2.5:1, or at the molar ratio of NaOH/ClCH 2 COOH ≈1.6–1.64, resulted in CMC products of relatively high water solubility. The viscosity-average molecular weight M v of these two CMC products obtained at molar ratios of 4.0:2.5:1 and 4.6:2.8:1 is in the range of 1.94 × 10 4 –2.48 × 10 4 g mol −1 , and the average DS of the two products are 0.57 and 0.85, respectively. As the solute concentration is above 2 wt%, the viscosity of the CMC-water solution exhibits nonlinear (exponential) increasing with increasing the solute concentration (typical of non-Newton fluids).

A method is presented for calculating the electromagnetic forces on the end windings of turbine generators for both the steady state and transient modes of operation. Part 1 of this paper deals with the basic concepts of the force calculation and gives several examples of steady state forces and how they vary with load and power factor. PartII deals with several types of transient operation. The currents and fields which these transients produce are discussed and forces are found for various cases such as short circuits, synchronizing out of phase and transmission line switching.

The microbial electrolysis desalination and chemical-production cell (MEDCC) is a device to desalinate seawater, and produce acid and alkali. The objective of this study was to enhance the desalination and chemical-production performance of the MEDCC using two types of stack structure. Experiments were conducted with different membrane spacings, numbers of desalination chambers and applied voltages. Results showed that the stack construction in the MEDCC enhanced the desalination and chemical-production rates. The maximal desalination rate of 0.58 ± 0.02 mmol/h, which was 43% higher than that in the MEDCC, was achieved in the four-desalination-chamber MEDCC with the AEM-CEM stack structure and the membrane spacing of 1.5mm. The maximal acid- and alkali-production rates of 0.079 ± 0.006 and 0.13 ± 0.02 mmol/h, which were 46% and 8% higher than that in the MEDCC, respectively, were achieved in the two-desalination-chamber MEDCC with the BPM-AEM-CEM stack structure and the membrane spacing of 3mm.

In order to identify a potential surrogate of planktonic ciliate communities for marine bioassessments and evaluating biological conservations, the different taxonomic/numerical resolutions and taxa as surrogates were studied in Jiaozhou Bay, northern China during a 1-year cycle (June 2007-May 2008).Samples were collected biweekly from a depth of 1 m at each of five sites. A range of physicochemical parameters were also measured in order to determine water quality.The genus- and family-level resolutions maintained sufficient information to evaluate the ecological patterns of the ciliate communities in response to environmental status. The non-loricate oligotrichous ciliate assemblages in both abundance and occurrence may be used as a surrogate of planktonic ciliate communities. Heavy data transformations were an optimal strategy for the species level of planktonic ciliates, while mild data transformations were for the higher. The ordination patterns based on species biomass, occurrence, and biomass/abundance ratio matrices were significantly consistent with that of species abundance data.The results suggest that the use of simplifications at both taxonomic and numerical resolutions are time-efficient and would allow improving sampling strategies of large spatial/temporal scale monitoring programs and biological conservation researches in the marine ecosystem with a relative paucity of scientists.

Since long ago, pelagic Sargassum mats have been known to be abundant in the Sargasso Sea, where they provide habitat to diverse organisms. However, over the last few years, massive amounts of pelagic Sargassum have reached the coast of several countries in the Caribbean and West Africa, causing economic and environmental problems. Aiming for lessening the impacts of the blooms, governments and private companies remove the seaweeds from the shore, but this process results expensive. The valorization of this abundant biomass can render Sargassum tides into an economic opportunity and concurrently solve their associated environmental problems. Despite the diverse fields where algae have found applications and the relevance of this recurrent situation, Sargassum biomass remains without large scale applications. Therefore, this review aims to present the potential uses of these algae, identifying the limitations that must be assessed to effectively valorize this bioresource. Due to the constraints identified for each of the presented applications, it is concluded that a biorefinery approach should be developed to effectively valorize this abundant biomass. However, there is an urgent need for investigations focusing on holopelagic Sargassum to be able to truly valorize this seaweed.

Abstract Microorganisms used in syngas fermentation require nutrients to grow and convert syngas (CO, H2 and CO2) into various products. Many of the essential nutrients can be provided by biochar. Poultry litter biochar (PLBC) contains minerals and trace metals and has a high pH buffering capacity, making it suitable as a nutrient supplement. The effects of PLBC loadings from 1 to 20 g L−1 on syngas fermentation were determined in 250 ml bottle assays. Results showed that 10 and 20 g L−1 PLBC significantly increased ethanol production compared to standard yeast extract (YE) medium. Fermentations in a 3L continuous stirred tank reactor (CSTR) with 10 g L−1 PLBC with and without 4-morpholineethanesulfonic acid (MES) showed 64% and 36% more ethanol production, respectively, than standard medium. The acetic acid accumulated at the beginning of fermentation was completely converted to ethanol in all media tested in the CSTR. These results demonstrate the feasibility of using PLBC medium without costly MES in the CSTR to enhance ethanol production from syngas for potential use at commercial scale.

A template‐agent can affect defect formation as well as influence interface properties, due to the rapid growth of perovskite film from the solution. Herein, diethylammonium iodide (DAI) is used as an effective template‐agent to control the perovskite crystallization during preparation. It is found that a very small amount of DAI in chlorobenzene (CB) can slow down the perovskite growth of the CH3NH3PbI3 (MAPbI3) film with more large grain size and compacted crystal‐grains resulting in the lesser grain boundaries (GBs) in favor of carrier transport in perovskite solar cells (PSCs). Moreover, some redundant PbI2 can be digested to form DA2PbI4. One part of DA2PbI4 can form the sub‐grains with the composition of (DA2PbI4)0.2(PbI2)0.8 to passivate the GB defects, and other part can cover the surface to passivate the surface defects in large MAPbI3 grains. Using an optimized DAI concentration of 0.5 mg mL−1 in CB solution, the corrsponding MAPbI3 PSC achieves an increased power conversion efficiency of 20.31% with suppressed current–voltage hysteresis. This DAI passivation strategy provides a simple approach to effectively assist the grain‐growth for improved device performance.

Abstract To obtain high yield and high concentration glucose from corncob residues (CRs), tetrahydrofuran (THF) + H2O co-solvent pretreatment was employed. The pretreatment parameters were firstly optimized by Box-Behnken Design of response surface method, and the maximum glucose yield (498.2 mg/g CRs) was obtained via enzymatic hydrolysis after pretreated under optimized conditions (53.7% THF concentration, 202.3 °C, 1.05 h). Then, the pretreated CRs under optimized conditions (optimized-CRs) were enzymatically hydrolyzed at high solid loading (15%–20%) and low enzyme input (5–8 FPU/g cellulose). The high concentration glucose production (128.6 mg/mL) was obtained from optimized-CRs after enzymatic hydrolysis at 20% solid loading with 10 FPU/g cellulose for 72 h, and then showed potential for reduction of enzyme input. Finally, the interactions between the 9 substrate-related factors and cellulose conversion were analyzed through correlation analysis, and found that Klason lignin remained in the cellulose-rich fractions and pseudo lignin condensed on the surface of the recovered substrate were the predominant inhibitors for enzymatic hydrolysis.

Inert gas is often used in the deoxygenation of microbial electrolysis cells (MECs) to maintain growth and viability of anaerobes. However, the effects of the gas atmosphere on hydrogen production and microbial community of MECs are often neglected. Here, the performances and biofilm microbiomes of MECs pre-sparged with different gases were compared. MECs pre-sparged with argon gas (Ar) yielded more hydrogen (3.73 ± 0.13 mol-H2/mol-acetate) and a higher hydrogen production rate (2.99 ± 0.17 L-H2/L-reactor-day) than MECs pre-sparged with N2 (3.41 ± 0.13 mol-H2/mol-acetate and 2.27 ± 0.28 L-H2/L-reactor-day, respectively). Microbiome analysis indicated that the relative abundance of Geobacter increased from 59.25% to 77.79% when the gas atmosphere in MECs shifted from N2 to Ar. Hydrogen production may have been catalyzed by nitrogenase from Geobacter and photosynthetic bacteria in MECs pre-sparged with Ar. These findings suggested that the gas atmosphere substantially influences the microbiome of anode biofilms and Ar sparging is most effective for enhancing hydrogen production in MECs.