• Energy Research
• Open Access close
• other engineering and technologies close
• CN close
• EU close
• EG close

AbstractDecarbonising the energy system requires high shares of variable renewable generation and sector coupling like power to heat. In addition to heat supply, heat pumps can be used in future energy systems to provide flexibility to the electricity system by using the thermal storage potential of the building stock and buffer tanks to shift electricity demand to hours of high renewable electricity production. Bridging the gap between two methodological approaches, we coupled a detailed building technology operation model and the open-source energy system model Balmorel to evaluate the flexibility potential that decentral heat pumps can provide to the electricity system. Austria in the year 2030 serves as an example of a 100% renewable-based electricity system (at an annual national balance). Results show that system benefits from heat pump flexibility are relatively limited in extent and concentrated on short-term flexibility. Flexible heat pumps reduce system cost, CO2 emissions, and photovoltaics and wind curtailment in all scenarios. The amount of electricity shifted in the assessed standard flexibility scenario is 194 GWhel and accounts for about 20% of the available flexible heat pump electricity demand. A comparison of different modelling approaches and a deterministic sensitivity analysis of key input parameters complement the modelling. The most important input parameters impacting heat pump flexibility are the flexible capacity (determined by installed capacity and share of control), shifting time limitations, and cost assumptions for the flexibility provided. Heat pump flexibility contributes more to increasing low residual loads (up to 22% in the assessed scenarios) than decreasing residual load peaks. Wind power integration benefits more from heat pump flexibility than photovoltaics because of the temporal correlation between heat demand and wind generation.

Hydrothermal liquefaction (HTL) is an effective way to treat solid wastes with high moisture content. The co-hydrothermal liquefaction (co-HTL) experiments of oily scum and poplar sawdust biochar at the different hydrothermal temperatures were performed in this work. The changes of the appearance and components of the liquid products were comprehensively studied. The results showed that the addition of biochar into oily scum significantly reduced the moisture content of the residue hydrochars obtained after co-HTL. As the hydrothermal temperature increased, the liquid products obtained from co-HTL turned clearer and lighter in color, and the recovery rate of the liquid products significantly increased. The co-HTL of bi-ochar and oily scum could effectively improve the liquid quality and enhance the recovery rate of hydrochars. The carbon numbers of the liquid products obtained from co-HTL were concentrated in C5-C11, which were main compositions of gas-oline. This work can provide basic data and theoretical reference for oily scum efficient treatment and engineering practice.

High penetration of renewable energy sources into isolated microgrids (µGs) is considered a critical challenge, as µGs’ operation at low inertia results in frequency stability problems. To solve this challenge, virtual inertia control based on an energy storage system is applied to enhance the inertia and damping properties of the µG. On the other hand, utilization of a phase-locked loop (PLL) is indispensable for measuring system frequency; however, its dynamics, such as measurement delay and noise generation, cause extra deterioration of frequency stability. In this paper, to improve µG frequency stability and minimize the impact of PLL dynamics, a new optimal frequency control technique is proposed. A whale optimization algorithm is used to enhance the virtual inertia control loop by optimizing the parameters of the virtual inertia controller with consideration of PLL dynamics and the uncertainties of system inertia. The proposed controller has been validated through comparisons with an optimized virtual inertia PI controller which is tuned utilizing MATLAB internal model control methodology and with H∞-based virtual inertia control. The results show the effectiveness of the proposed controller against different operating conditions and system disturbances and uncertainties.

The battery power state (SOP) is the basic indicator for the Battery management system (BMS) of the battery energy storage system (BESS) to formulate control strategies. Although there have been many studies on state estimation of lithium-ion batteries (LIBs), aging and temperature variation are seldom considered in peak power prediction during the whole life of the battery. To fill this gap, this paper aims to propose an adaptive peak power prediction method for power lithium-ion batteries considering temperature and aging is proposed. First, the Thevenin equivalent circuit model is used to jointly estimate the state of charge (SOC) and SOP of the lithium-ion power battery, and the variable forgetting factor recursive least squares (VFF-RLS) algorithm and extended Kalman filter (EKF) are utilized to identify the battery parameters online. Then, multiple constraint parameters including current, voltage, and SOC were derived, considering the dependence of the polarization resistance of the battery on the battery current. Finally, the verification experiment was carried out with LiFePO4 battery. The experimental results under FUDS operating conditions show that the maximum SOC estimation error is 1.94%. And the power prediction errors at 20%, 50%, and 70% SOC were 5.0%, 8.1% and 4.5%, respectively. Our further work will focus on the joint estimation of battery state to further improve the accuracy.

AbstractVentilation door are commonly found in tunnels and other underground engineering ventilation structures, disaster periods using its explosion isolation, explosion relief, wind regulation characteristics for disaster prevention and mitigation is of great significance. This paper numerically simulates the propagation characteristics of the gas explosion shock wave in the nearby tunnel when the ventilation door are opened at different degrees, and analyzes the influence mechanism of the opening degree on the change law of the shock wave overpressure distribution in the nearby tunnel. The results show that the shock wave forms a strong turbulence area (high pressure area) on both sides in front of the ventilation door, and the area range and the overpressure value decrease with the increase of the opening degree; the ventilation door reduce the intensity of the shock wave, so that the overpressure behind the ventilation door decreases, and the smaller the opening degree, the lower the overpressure behind the ventilation door. The secondary explosion formed shock wave and the ventilation door reflected shock wave meet to form a stronger shock wave, which leads to different opening degrees of ventilation door, its before, after the roadway and after the bifurcation of the main roadway in the measured points of the overpressure change curve is different, the main difference is that the peak overpressure for the first wave or the second wave peak. The peak overpressure in the tunnel before and after the ventilation door decreases and increases respectively with the increase of the opening length, and the overall decay of the peak overpressure at 5 m and 10 m before the ventilation door is 49.56% and 4.04% respectively and only has an effect on the peak overpressure in main tunnel within 20 m from the bifurcation.

In this paper, the mathematical analysis of the robot effective mass is presented. The calculation of this effective mass and its ellipsoid are included. The relationship between the robot effective mass and the external force (collision) affecting the robot end-effector is investigated. The effective mass is analyzed using different robot configurations and different end-effector positions. This analysis is conducted using 2-DOF and 3-DOF planar robots and executed using MATLAB. The results from this analysis prove that the robot effective mass depends on the its configurations and end-effector position. Effective mass can thus be considered as one of the criteria in optimizing robot kinematics and configuration.

A GIS-based method is proposed to identify critical links in urban road networks. This study utilizes a geographic information system (GIS) to evaluate the distribution of road infrastructure, road density, and network accessibility at the micro, meso, and macro levels. At the micro level, GIS is used to assess the distribution of public facilities along the roads. At the meso level, a city’s road density distribution is evaluated. At the macro level, a spatial barrier model and a transportation network model are constructed to assess the network accessibility. An inverse distance weighting method is employed to interpolate the accessibility. Furthermore, a network topology is established, and the entropy method is utilized to evaluate the sections comprehensively. The sections are ranked based on the evaluation results to identify the critical links in the urban road network. The road-network data and points of interest (POI) data from the Anning District in Lanzhou are selected for a case study, and the results indicate that the top five critical links have scores of 0.641, 0.571, 0.570, 0.519, and 0.508, respectively. Considering the three indicators enhances the accuracy of critical section identification, demonstrating the effectiveness of the proposed method. Visualizing each indicator using GIS 10.7 provides a new approach to identifying critical links in urban road networks and offers essential theoretical support for urban planning.

The present study measured the relative efficiency of five major commercial ports in West Africa, using three different Data Envelopment Analysis (DEA) methods, the CCR, BCC, and Windows I-C methods over the years 2005-2016. Seven input variables and one output variable were used in the model analysis. The CCR and BCC methods were used to evaluate the technical and scale efficiency while the Windows I-C method provided a comprehensive ranking of the studied ports. The results showed that the scale efficiency score of 89.53% indicated that on average the production scale of the ports had deviated from the most productive scale size (MPSS) by 10.47%. These results revealed that the source of the overall inefficiency is due to scale rather than pure technical inefficiency. Hence, in order to improve the overall efficiency, the two scaled inefficient ports of Abidjan and Cotonou should adjust their scale of operations. Then, further investigations were conducted to detect correlations between various variables used in this study. The research found that the absence of any correlation for non-significant variables and negative correlation for the significant variables throughout time resulted from the fact that these variables were not fully utilized. Meaning that they were not efficiently used to boost the container throughput on a scale basis, the research also found that a pandemic or insecurity could easily impact seaports activities with the case of the Ebola outbreak which strucked the West African region from the year 2013 to 2016, or the terrorism threats which prevailed in the region around the year 2012. Thus, for ports to stand out in the present fiercely competitive environment, ports authorities ought to analyze their operational scale to identify whether or not the production size is fitting before further port capacity expansion.

The vehicle will generate an amount of current while the electric vehicle just starting to regeneratively brake. In order to avoid the impact of high current on the traction battery, a novel electrohydraulic hybrid electric vehicle has been proposed. The main power source is supplied by the electric drive system, and the hydraulic system performs the auxiliary drive system that fully exerts the advantages of the electric drive system and the hydraulic drive system. A proper regenerative braking control strategy is presented, and the control parameters are determined by the fuzzy optimization algorithm. The simulation analysis built the model through the united simulation of AMESim and MATLAB/Simulink. The results illustrated that the optimized control strategy can reduce battery consumption by 1.22% under NEDC-operating conditions.