• Energy Research
• physical sciences close
• CN close
• DE close
• NL close

AbstractIron-acceptor (FeAc) pair association has been studied in compensated n-type silicon. A dynamic approach, based on the charge carrier recombination rates over the Fei trap level, leads to an explanation of the observed FeAc pairing reaction in compensated n-type silicon and extends the understanding of FeAc pairing kinetics. Association kinetics was used to measure a height dependent acceptor concentration profile. Even in compensated n-type silicon good agreement with expected concentrations is found.

Characteristics of Tm:YAG ceramic for high efficient 2-μm lasers are analyzed. Efficient diode end-pumped continuous-wave and Q-switched Tm:YAG ceramic lasers are demonstrated. At the absorbed pump power of 53.2W, the maximum continuous wave (cw) output power of 17.2 W around 2016 nm was obtained with the output transmission of 5%. The optical conversion efficiency is 32.3%, corresponding to a slope efficiency of 36.5%. For Q-switched operation, the shortest width of 69 ns was achieved with the pulse repetition frequency of 500 Hz and single pulse energy of 20.4 mJ, which indicates excellent energy storage capability of the Tm:YAG ceramic.

AbstractThis paper presents an experimental assessment of a blended fatigue‐extreme controller for load control employing trailing edge flaps on a lab‐scale wind turbine. The controller blends between a repetitive model predictive controller that targets fatigue loads and a dedicated extreme load controller, which consists of a simple on‐off load control strategy. The Fatigue controller uses the flapwise blade root bending moments of the three blades as input sensors. The Extreme controller additionally uses on‐blade angle of attack and velocity measurements as well as acceleration measurements to detect extreme events and to allow for a fast reaction. The experiments are conducted on the Berlin Research Turbine within the large wind tunnel of the TU Berlin. In order to reproduce test cases with deterministic extreme wind conditions that follow industry standards, the wind tunnel was redesigned. The analyzed test cases are extreme direction change, extreme coherent gust, extreme operating gust and extreme coherent gust with direction change. The test cases are analyzed by on‐blade angle of attack and velocity measurements. The load control performance of the Blended controller is compared to the pure fatigue oriented and the pure extreme load controller. The Blended controller achieves a maximum flapwise blade root bending moment reduction of 23%, which is comparable to the reduction achieved by the Extreme controller.

In the search for a nontoxic replacement of the commonly employed CdS buffer layer for Cu(In,Ga)(S,Se) $_\mathrm{2}$ based solar cells, chemically deposited Zn(O,S) thin films are a most promising choice. In this paper, we address the usually slow deposition speed of Zn(O,S) in a newly developed ammonia-free chemical bath process, resulting in a deposition of 30 nm in 3 min with good homogeneity on 30 cm × 30 cm sized substrates. Solar cells with buffer layers prepared from this process match the efficiency of CdS reference cells. In a second step, we address the light-soaking post-treatment, still needed for maximum efficiencies. By addition of aluminum to the deposition process, the initial efficiencies can be increased slightly. With the addition of boron, the light-soaking post-treatment is rendered unnecessary, while maintaining high efficiencies above 15%, surpassing reference cells with CdS buffer.

Abstract An alkaline earth boro-aluminosilicate glass (Eagle XG), a soda-lime glass, and a light-weight polyethylene-terephthalate (PET) foil, used as typical substrates for photovoltaics, were treated by an energetic proton beam (3 MeV, dose 106–107 Gy) corresponding to approx. 30 years of operation at low Earth orbit. Properties of the irradiated substrates were characterized by atomic force microscopy, optical absorption, optical diffuse reflectance, Raman spectroscopy, X-ray photoelectron spectroscopy, Fourier-transform infrared (FTIR) spectroscopy, and terahertz (THz) spectroscopy. Minimal changes of optical and morphological properties are detected on the bare Eagle XG glass, whereas the bare PET foil exhibits pronounced increase in optical absorption, generation of photoluminescence, as well as mechanical bending. On the other hand, the identical substrates coated with Indium-tin-oxide (ITO), which is a typical material for transparent electrodes in photovoltaics, exhibit significantly higher resistance to the modifications by protons while ITO structural and electronic properties remain unchanged. The experimental results are discussed considering a potential application of these materials for missions in space.

Abstract The molten droplet fragmentation dominated by hydrodynamic mechanisms is the key process at the stage of pressure propagation in the process of the fuel–coolant interaction (FCI) which may occur during the course of a severe accident in a light water reactor (LWR). However, due to complication of the process, hydrodynamic fragmentation cannot be described by a particular mechanism, and there is no sufficient experimental studies under high pressure shock condition for this kind of fragmentation evaluation. In this paper, a multi-phase thermal hydraulic code with the Volume of Fluid Method (VOF) is developed, Continuum surface force (CSF) model is employed to compute the surface tension. The breakup process of a molten droplet under sudden accelerations is numerically analyzed to investigate the mechanism of fragmentation in vapor explosion. The results show that the breakup process experiences two stages: deformation and disintegration, which agrees with the simulation by Duan et al. (2003) using Moving Particle Semi-implicit (MPS) method. It is found that an increase in intensity of pressure pulse will accelerate the completion of breakup process and the dimensionless breakup time from the simulation is not strongly affected by Bond number ( Bo ). The simulation results suggest that the deformation imposed by the external hydrodynamic pressure distribution should be the dominant factor in breakup process for molten droplets in liquid–liquid system simulated in this paper.

Safety and Security Science