• Energy Research
• engineering and technology close
• 6. Clean water close
• CN close
• US close
• AU close
• DE close

This paper presents an analysis of the problem of reorientation of a riser pipe from an initially horizontal configuration during subsurface tow to the vertical position for installation. Front and rear barges support the pipe through cables. The orientation into a vertical configuration is accomplished by paying out the front cable. The pipe is treated as a Bernoulli-Euler beam with significant tension undergoing large angle deflections. A finite element procedure used state transfer matrices and successive linearization and the results show that the stress critical phase occurs when the pipe is going through the 60-deg angle to the horizontal direction.

Abstract In this study, crude cellulose derived from cornstalk, after bleaching, was used as raw material for the synthesis of sodium carboxymethyl cellulose (CMC) by reacting with the cellulose with NaOH and chloroacetic acid at 75 °C for 1.5 h. Effects of alkali dosage, concentration of chloroacetic acid on the physical and chemical properties of the CMC products were investigated. It was revealed that the reactants alkali reagent/chloroacetic acid/cellulose at the molar ratio of 4.6:2.8:1and 4:2.5:1, or at the molar ratio of NaOH/ClCH 2 COOH ≈1.6–1.64, resulted in CMC products of relatively high water solubility. The viscosity-average molecular weight M v of these two CMC products obtained at molar ratios of 4.0:2.5:1 and 4.6:2.8:1 is in the range of 1.94 × 10 4 –2.48 × 10 4 g mol −1 , and the average DS of the two products are 0.57 and 0.85, respectively. As the solute concentration is above 2 wt%, the viscosity of the CMC-water solution exhibits nonlinear (exponential) increasing with increasing the solute concentration (typical of non-Newton fluids).

The microbial electrolysis desalination and chemical-production cell (MEDCC) is a device to desalinate seawater, and produce acid and alkali. The objective of this study was to enhance the desalination and chemical-production performance of the MEDCC using two types of stack structure. Experiments were conducted with different membrane spacings, numbers of desalination chambers and applied voltages. Results showed that the stack construction in the MEDCC enhanced the desalination and chemical-production rates. The maximal desalination rate of 0.58 ± 0.02 mmol/h, which was 43% higher than that in the MEDCC, was achieved in the four-desalination-chamber MEDCC with the AEM-CEM stack structure and the membrane spacing of 1.5mm. The maximal acid- and alkali-production rates of 0.079 ± 0.006 and 0.13 ± 0.02 mmol/h, which were 46% and 8% higher than that in the MEDCC, respectively, were achieved in the two-desalination-chamber MEDCC with the BPM-AEM-CEM stack structure and the membrane spacing of 3mm.

Microwave-assisted alkali pre-treatment of wheat straw and its enzymatic hydrolysis were investigated and compared with the conventional alkali pre-treatment process. First, the effect of microwave power and pre-treatment time on the weight loss and composition of wheat straw was examined. The results show that the higher microwave power with shorter pre-treatment time and the lower microwave power with longer pre-treatment time had the same effect on the weight loss and composition at the same energy consumption. The comparison was then made between the effect of the microwave-assisted alkali pre-treatment and the conventional alkali one on the weight loss and composition of wheat straw. The wheat straw had a weight loss of 48·4% and a composition of cellulose 79·6%, lignin 5·7% and hemicellulose 7·8% after 25 min microwave-assisted alkali pre-treatment at 700 W, compared with a weight loss of 44·7% and a composition of cellulose 73·5%, lignin 7·2% and hemicellulose 11·2% after 60 min conventional alkali pre-treatment. The microwave-assisted alkali pre-treatment removed more lignin and hemicellulose from wheat straw with shorter pre-treatment time compared with the conventional alkali one. Finally, the enzymatic hydrolysis of pre-treated wheat straw (substrate concentration 50 g l−1, enzyme loading 20 mg g−1 substrate) was also investigated and the results indicate that the microwave-assisted alkali pre-treated wheat straw had higher hydrolysis rate, reducing sugar concentration and glucose content in the hydrolysate than the conventional alkali pre-treated one. Microwave-assisted alkali pre-treatment is a potential alternative of wheat straw pre-treatment for its enzymatic hydrolysis.

Abstract Microorganisms used in syngas fermentation require nutrients to grow and convert syngas (CO, H2 and CO2) into various products. Many of the essential nutrients can be provided by biochar. Poultry litter biochar (PLBC) contains minerals and trace metals and has a high pH buffering capacity, making it suitable as a nutrient supplement. The effects of PLBC loadings from 1 to 20 g L−1 on syngas fermentation were determined in 250 ml bottle assays. Results showed that 10 and 20 g L−1 PLBC significantly increased ethanol production compared to standard yeast extract (YE) medium. Fermentations in a 3L continuous stirred tank reactor (CSTR) with 10 g L−1 PLBC with and without 4-morpholineethanesulfonic acid (MES) showed 64% and 36% more ethanol production, respectively, than standard medium. The acetic acid accumulated at the beginning of fermentation was completely converted to ethanol in all media tested in the CSTR. These results demonstrate the feasibility of using PLBC medium without costly MES in the CSTR to enhance ethanol production from syngas for potential use at commercial scale.

In the water-rich karst regions, high water and mud outbursts are common geological disasters in tunnel construction. To ensure the safe and smooth construction of tunnel projects, it is necessary to consider anti-water pressure, water inrush prevention and geological disasters during the design of tunnels. Based on the Yongfutun Tunnel Project, this paper studies the application and effect of radial grouting and curtain grouting, which involves those in high-water-pressure tunnels under double-layer support conditions. To obtain the effects and parameters of radial grouting and curtain grouting, the influences of different grouting ranges on the tunnel’s surrounding rocks and supporting structures were analyzed and the finite difference method was adopted. The results show that the radial grouting of the surrounding rock can notably improve the initial support of the tunnel, but the impact is less obvious when the grouting range exceeds 4 m. The design of radial grouting is recommended to be 4.0 m to 4.5 m. Curtain grouting can effectively reduce the external water pressure of the tunnel lining. The external water pressure of the grouting area is 23% greater than that without curtain grouting. Curtain grouting can slow down the infiltration of external water pressure. This is beneficial to the stress of the tunnel lining structure, but the improvement in initial support force is slight. Moreover, curtain grouting improves the safety reserve of the secondary lining by strengthening the self-stability ability of the surrounding rock. Meanwhile, the double-layer primary support can effectively share the external water pressure and surrounding rock pressure. This study provides a certain reference for the lining design of high-water-pressure tunnels.

Abstract In this paper, coupled governing equations were proposed to simulate three-dimensional heat conduction and moisture transport in the nuclear waste repository. Because there will be a large temperature gradient near inner and outer boundaries of the bentonite buffer layer, and the heat driven moisture transport is introduced in the governing equation of moisture transport. By applying the Fourier and Laplace transforms, the governing equations were converted to the Bessel equations, and the Laplace-domain solutions to temperature and moisture distributions were derived through the inverse Fourier transform. The reliability of the proposed solutions was verified through comparative analysis with the line heat source model. These analytical solutions were applied to obtain the evolutions of temperature field and moisture distribution near the waste canister. Finally, a sensitivity study was performed to analyze the effects of relevant parameters on the heat driven moisture transport.

Energy is consumed at every stage of the cycle of water production, distribution, end use, and recycled water treatment. Understanding the nexus of energy and water may help to minimize energy and water consumption and reduce environmental emissions. However, the interlinkages between water and energy have not received adequate attention. To address this gap, this paper disaggregates and quantifies the energy consumption of the entire water cycle process in Beijing. The results of this study show that total energy consumption by water production, treatment and distribution, end use, and recycled water reuse amounts to 55.6 billion kWh of electricity in 2015, or about 33% of the total urban energy usage. While water supply amount increased by only 10% from 2005 to 2015, the related energy consumption increased by 215% due to water supply structural change. The Beijing municipal government plans to implement many water saving measures in the area from 2016 to 2020, however, these policies will increase energy consumption by 74 million kWh in Beijing. This study responds to the urgent need for research on the synergies between energy and water. In order to achieve the goal of low-energy water utilization in the future, water and energy should be integrated in planning and management.

Abstract CBM reservoirs are extremely vulnerable to damage due to their complex pore structure. So, changing pore structures in CBM reservoirs is of vital importance for reducing reservoirs damage. Organic solvents have been considered as additives into fracturing fluids to enhance production because they can enhance the pore connectivity and loosening macromolecular network structure. It is thus of great interests to investigate how organic solvents (ethanol and ethylene glycol ether) change micropore structures and fluid distribution. In this study, samples were selected from different wells completed in No. 3 coal seam, Zhaozhuang minefield. Low-pressure nitrogen adsorption (LP-N2GA) experiments were conducted on coal samples to evaluate the changes in pore-structure parameters including specific surface area (SSA), pore diameter, and pore volume. NMR experiments were conducted on coal samples to evaluate the changes in fluid distribution. Analyzing the LP-N2GA results suggests ethylene glycol ether and ethanol can effectively increase SSA, pore diameter, and opening degree of pores in coal samples. Comparative analysis of NMR results indicates that ethylene glycol ether consistently reduces the irreducible water saturation (Swir) in samples. The average value of Swir of raw samples is 0.8670 and the average value of Swir of samples treated with ethylene glycol ether value is 0.7644. Considering the pore-structure alterations, this study demonstrates that ethylene glycol ether is more preferable for enhancing recovery from CBM reservoirs compared with ethanol.