• Energy Research
• Closed Access close
• Restricted close
• DE close
• CA close
• BE close

Abstract In this study, crude cellulose derived from cornstalk, after bleaching, was used as raw material for the synthesis of sodium carboxymethyl cellulose (CMC) by reacting with the cellulose with NaOH and chloroacetic acid at 75 °C for 1.5 h. Effects of alkali dosage, concentration of chloroacetic acid on the physical and chemical properties of the CMC products were investigated. It was revealed that the reactants alkali reagent/chloroacetic acid/cellulose at the molar ratio of 4.6:2.8:1and 4:2.5:1, or at the molar ratio of NaOH/ClCH 2 COOH ≈1.6–1.64, resulted in CMC products of relatively high water solubility. The viscosity-average molecular weight M v of these two CMC products obtained at molar ratios of 4.0:2.5:1 and 4.6:2.8:1 is in the range of 1.94 × 10 4 –2.48 × 10 4 g mol −1 , and the average DS of the two products are 0.57 and 0.85, respectively. As the solute concentration is above 2 wt%, the viscosity of the CMC-water solution exhibits nonlinear (exponential) increasing with increasing the solute concentration (typical of non-Newton fluids).

The passivation of iron and steel (DIN 1623) was studied by integral and depth selective conversion electron Mossbauer spectroscopy and Auger electron spectroscopy. Thickness and phase composition of the passive layer formed in sulphate solution and in a phosphate buffer were determined in dependence on the anodic potential and the duration of the passivating procedure. The experimental results lead to the conclusion that not the whole oxidic layer is responsible for the passivity but only a very thin intermediate layer formed between the cubic substrate and the rhombic oxide (γ-FeOOH) cover.

A detailed analysis of the effects of ground grid configuration on grounding performance has been carried out for uniform and horizontally stratified soils with multiple layers. The results of the analysis reveal that the most efficient and cost-effective design is highly dependent on soil structure type and characteristics. In the absence of ground rods, grounding grids with uniform mesh size are quite efficient in soils having a thin (relative to grid size) high resistivity (relative to the lower layers) top soil, while grids with small mesh size at the periphery of the grid provide optimum performance in uniform soils and soils with low resistivity top soils. Ground rods were found to be effective only when a significant portion of their length is in contact with a low resistivity soil, as expected.

Experiments were carried out to determine the accuracy and validity of estimations of hepatic blood flow from systemic clearances of ethanol during very low dose (8 μmol∙min−1∙kg−1) infusions of ethanol in anesthetized cats. Systemic clearances were compared with directly measured hepatic blood flow using a hepatic venous long-circuit technique. This technique allowed direct measurement and alteration of hepatic blood flow and collection of arterial, portal, and hepatic venous blood samples without depletion of the animal's blood volume. In 18 cats, Vmax for ethanol was 93 ± 7 μmol∙min−1 per 100 g liver or 21 ± 2 μmol∙min−1∙kg·body weight−1 and Km was 144 ± 19 μM in terms of logarithmic mean sinusoidal concentration. At the dose of 8 μmol∙min−1∙kg body weight−1 used for estimation of hepatic blood flow, extraction was 0.95 ± 0.07 (mean ± SD). Systemic clearance of ethanol overestimated directly measured hepatic blood flow by 15 ± 16%. Hepatic blood flow changes expressed as percentages of the control level were accurately estimated from systemic ethanol clearance (100 ± 10%). Since 73 ± 12% of the infused ethanol was eliminated by the liver and 83 ± 11% was eliminated by the splanchnic bed, an extrasplanchnic uptake of 17% accounted for the overestimation of hepatic blood flow. Estimation of hepatic blood flow from systemic clearances of ethanol during very low dose infusions may have advantages over other clearance methods. Its use in cats was illustrated in a separate series of experiments and it was shown that surgery significantly reduced hepatic blood flow. The method may merit trial for estimation of hepatic blood flow in humans.

Current energy market designs and pricing schemes fail to give investors the appropriate market signals. In particular, energy prices are not high enough to attract investors to build new or maintain existing power capacity. In this paper we propose a method to compute second-best Pareto optimal equilibrium prices for any market exhibiting non-convexities and, based on this result, an energy market design able to restore the correct energy price signals for supply investors.

Abstract Thermal performance of three naturally ventilated public buildings in which the wind tower is an important architectural freature is studied. One of the three builidings as well as it's wind tower is instrumented for temperature, relative humidity and airflow velocity measurements, and the other two are instrumented for temperature measurement. The results have led to a discussion concerning the degree of wind tower effectiveness in achieving thermal comfort.

Abstract Bio-based polyurethane (BPU) foams were successfully prepared using hydrothermally liquefied wheat straw (WS) to substitute a mass fraction of up to 50% of polyols. Response surface methodology (RSM) based on central composite design (CCD) was employed to optimize four process parameters: NCO/OH molar ratio, loading of crosslinking agent (glycerol), loading of catalyst (a mixture of triethylene diamine, stannous octoate, and triethanolamine), and loading of blowing agent (water) for the maximum compression strength of the rigid BPU foams. With the quadratic orthogonal regression model, verified by experimentation, the maximum compression strength of approximately 180 kPa was obtained at the following optimal conditions: NCO/OH molar ratio of 1.24:1, glycerol addition of 12.11%, catalyst loading of 0.76%, and blowing agent addition of 1.31% in relation to the total mass of polyols. The BPU foam prepared at the optimal conditions exhibits good thermal conductivity (0.045 Wm−1K−1) and thermal stability, comparable to those of a reference foam prepared with 100% PPG400.

Abstract In many visions and roadmaps, there is a broad agreement that fuel cells – both for stationary and mobile applications – are the key technology to allow the development of a hydrogen infrastructure. Furthermore, this development is generally thought to be based on a gradual, decentralised evolution. Nevertheless, in this paper it is argued that, taking into account the entire hydrogen chain (production, transport, storage, distribution and end-use), this decentralised fuel-cell based philosophy shows some serious flaws. Therefore, a new hydrogen-transition approach was pushed forward: mixing in of hydrogen into the natural-gas bulk. Using Flanders – the Northern part of Belgium – as a case study, the development of a transitory hydrogen infrastructure has been studied, taking into account the entire hydrogen chain and its dynamics, from production to end use. In a next step, this transition is being quantified. An optimisation model has been developed using Matlab and the commercial solvers GAMS and CPLEX. Following a mixed-integer linear-programming approach, this model is able to determine the economically optimal hydrogen-production mix and operational behaviour of each hydrogen-production plant separately. The model then allows gaining valuable insights in the importance of storage and the influence of fuel prices and carbon taxes with regard to the development of an early hydrogen economy.

AbstractThe presented synthesis of the title compounds (II), (IV), (VI) and (VIII) is extremely simple and highly efficient without the use of any chromatographic purification.