• Energy Research
• Closed Access close
• Open Source close
• DE close
• FR close
• DLR publication server close

Abstract In many cases, hazardous wastes are subject to thermal treatment at elevated temperatures. Some types of wastes do not have a sufficient calorific value to cover the heat demand of the high temperature process. For thermal treatment of e.g. filter residues, dusts, sulfuric acid, aluminium dross, foundry sand, or waste water, supplementary energy supply is needed. The specific energy demand ranges from 0.5 to 2.5 kWh/kg (2–10 MJ/kg). An important aim of process optimisation is the reduction of (fossil) energy consumption and exhaust gas flow. Concentrated solar energy promises advantages when applied to high energy consuming waste treatment processes with regard to substitute fossil or electric energy consumption, to reduce CO2 emissions, and exhaust gas flow. In parallel to conceptional studies, a solar-heated rotary kiln mini-plant has been designed and constructed for tests in the DLR solar furnace. The tests will give indications of boundary conditions for solar thermal treatment or conversion of selected hazardous materials.

Proton conducting ceramics (PCC) cells are promising energy conversion devices that enable high efficiency energy conversion at lower temperature range, solving the challenge of conventional solid oxide cells (SOCs) due to the high operating temperature. Electrochemical performance and chemical stability of PCC electrolyte has been investigated in recent studies, suggesting that rare-earth doped Ba(Zr,Ce)O3 perovskite-type ceramics are optimal materials exhibiting high proton conductivity and chemical stability during operations. On the contrary, mechanical stability of these PCC electrolyte materials has not been evaluated despite the fact that the mechanical properties are critically important for achieving long-term stable operation as fuel cells or electrolyser cells. For the development of conventional SOCs, mechanical stability during high temperature operation was one of the most significant challenges to deal with, which was attained as a result of detailed studies on in-situ elastic properties of composing materials such as oxygen ion conducting electrolytes and residual stresses. Similarly, for PCC cells, mechanical properties of cells and composing materials have been of significant interest in order to achieve mechanically stable long-term operation, even though PCC cells operate at lower temperature than SOCs. Furthermore, the metal-supported (MS) structure which provides superior mechanical robustness compared to anode-supported (AS) structure is expected to be applied effectively to PCC cells, which are called proton conducting ceramics – metal-supported cells (PCC-MSCs), leading to greater necessity of the mechanical evaluation of the cells and composing materials. Electrolyte is the most crucial component in an electrochemical cell and must be mechanically stable because ion transport and gas tightness made by electrolyte determines electrical performance. However, there has been important concern that larger thermal stresses might be introduced in PCC cells compared to SOCs, resulting from the thermal expansion coefficient (TEC) mismatch between the electrode and electrolyte and from the chemical expansion by the hydration that occurs in a certain temperature range. The PCC electrolyte is highly in need of investigation on in-situ mechanical properties, especially on elastic properties. In this study, elastic properties of electrochemically promising PCC, Y-doped Ba(Zr,Ce)O3 perovskite-type ceramics, were investigated under high temperature conditions. Elastic moduli such as Young’s modulus and Poisson’s ratio were measured by the method that we previously developed for elastic investigation in high temperature conditions using ultrasonic waves. This method enables highly accurate and repetitive examination of elastic properties at high temperatures in materials with poor sinterability including PCC by measuring ultrasonic sound velocities in pellets typically fabricated for electrochemical tests. Pellets of BaZr1-xYxO3-δ (BZY) with different concentrations of doped yttrium, BaZr0.9Y0.1O3-δ (BZY10), BaZr0.85Y0.15O3-δ (BZY15), and BaZr0.8Y0.2O3-δ (BZY20), were fabricated. Additionally, pellets of BaZryCe1-yY0.1O3-δ (BZCY) with different ratio of Ce to Zr, BaZr0.7Ce0.2Y0.1O3-δ (BZCY721) and BaZr0.8Ce0.1Y0.1O3-δ (BZCY811) were fabricated. Powders of PCCs above were consolidated to be thick rounded shape and sintered in air. Each prepared sample was set in an electric furnace in laboratory air atmosphere and sound velocities were measured with the sample slowly heated up to 700 °C and subsequently cooled down to room temperature to calculate elastic moduli at each measuring point. In the first series of heating and cooling measurements for as-sintered samples, hysteresis on elastic moduli in intermediate temperature range was observed. We repeatedly conducted a series of heating and cooling measurements several times, and then the hysteresis was not observed any further. Fig.1 shows final state Young’s modulus of BZCY721, BZCY811, and BZY10 (BZCY901) without hysteresis. Elastic moduli at room temperature have not changed through multiple heating and cooling measurements, and crystal structures and lattice parameters were also confirmed to remain constant by x-ray diffraction (XRD) analysis. The hysteresis found in a specific temperature range suggests that elastic moduli were influenced presumably by a change in defect structure of PCC caused by hydration or defect association of oxygen vacancies and dopants. At room temperature, Young’s modulus decreased with the increment of Ce concentration by 16 % from BZY10 to BZCY721. When materials have the same crystalline structure, Young’s modulus generally decreases as mean atomic volume of the base crystal increases. Because BaCeO3 has larger mean atomic volume than BaZrO3, this observation is qualitatively reasonable. However, in high temperatures, the difference became significant only for BZCY721, Young’s modulus decreased by 30 % from that at room temperature in BZCY721. These results suggest that Ce substitution causes different high temperature dependences. Figure 1

Inactivation, mutagenesis of histidine reversion and the involvement of DNA repair were studied in spores of Bacillus subtilis irradiated with heavy ions at LBL, Berkeley and GSI, Darmstadt. Five groups of ions (from boron to uranium) were used with residual energies from 0.2 MeV/u up to 18.6 MeV/u; in addition, carbon ions were used with a residual energy of 120 MeV/u. Action cross sections of both inactivation and mutagenesis show a similar dependence on ion mass and energy: for lighter ions (Z less than or equal to 10), the lethal response is nearly energy independent (Z = 10) or decreasing with energy (Z less than or equal to 6); these light ions, up to 18.6 MeV/u, induce hardly any mutations. For heavier ions (Z greater than or equal to 26), the lethal as well as the mutagenic responses increase with ion mass and energy up to a maximum or saturation. The efficiency of DNA repair to improve survival and the mutagenic efficiency per lethal event, both, increase with ion energy up to a saturation value which, depending on strain and endpoint, either roughly coincides with the X-ray value or is smaller than that after X-ray treatment. For repair based on recombination events, the increase in the survival effects with ion energy is more pronounced than for that based on repair replication. At energies of 1 MeV/u or below, neither DNA repair nor mutation induction appear to be significant. The results support previous suggestions on the importance of the radial distribution of the energy around the ion track in biological action cross section and the evidence that the entire core of the spore represents the sensitive site in responses to heavy ions.

We utilize a range of emission scenarios for shipping to determine the induced global-mean radiative forcing and temperature change. Ship emission scenarios consistent with the new regulations on nitrogen oxides (NO(x)) and sulfur dioxide (SO(2)) from the International Maritime Organization and two of the Representative Concentration Pathways are used as input to a simple climate model (SCM). Based on a complex aerosol-climate model we develop and test new parametrizations of the indirect aerosol effect (IAE) in the SCM that account for nonlinearities in radiative forcing of ship-induced IAE. We find that shipping causes a net global cooling impact throughout the period 1900-2050 across all parametrizations and scenarios. However, calculated total net global-mean temperature change in 2050 ranges from -0.03[-0.07,-0.002]°C to -0.3[-0.6,-0.2]°C in the A1B scenario. This wide range across parametrizations emphasizes the importance of properly representing the IAE in SCMs and to reflect the uncertainties from complex global models. Furthermore, our calculations show that the future ship-induced temperature response is likely a continued cooling if SO(2) and NO(x) emissions continue to increase due to a strong increase in activity, despite current emission regulations. However, such cooling does not negate the need for continued efforts to reduce CO(2) emissions, since residual warming from CO(2) is long-lived.