• Energy Research
• 7. Clean energy close
• 11. Sustainability close
• 12. Responsible consumption close
• DE close
• IT close
• EU close

Abstract Hybrid energy storage is a multi-modal approach to store and supply different forms of energy (electricity, heat, cold) simultaneously. This is an important sector coupling approach and enables large scale flexibility for a deep decarbonization of energy systems. Two different proposed energy storages – power-to-heat-to-X energy storage (PHXES) and pumped thermal energy storage (PTES) – are investigated in detail in this work towards their potential towards a hybrid deployment. The techno-economic analysis includes thermodynamic flowsheet simulations and unified cost estimations based on the used equipment. It is shown that the main input data set (e.g. working fluid selection, turbomachinery efficiency, pinch temperatures) has a strong influence on storage roundtrip efficiency in the thermodynamic simulations, but also on storage costs. Cost decrease and performance increase can be conflicting development targets, and it is not clear if future energy systems rather require technologies with the highest storage efficiencies or if low cost is an important prerequisite. PHXES and three variants of PTES are implemented into a simplified energy system model of the city of Hamburg that comprises the electric load and heat demand of the district heating system. Two scenarios (fossil benchmark and 80% decarbonization) are used to select the technologies and their capacities that allow the most cost-effective energy supply solution by a linear-programming optimization procedure. Large scale renewable power generation and hybrid energy storage play the major roles in the decarbonization scenario. PHXES with a storage capacity of 69 GWh, hot water storage (3.6 GWh) and a battery system (430 MWh) are part of the cost-optimal solution. A cost sensitivity analysis shows that a total cost reduction of 60–80% is required for PTES to become competitive in this model scenario.

Two stage premixed combustor with variable geometry has been developed to meet stringent NOx goals in Japan without the use of water or steam injection. This combustion system is planned to be applied for 120-MW gas turbine in 1090-MW LNG combined cycle plant. The full-pressure, full-scale combustion tests were conducted over a wide range of operating conditions for this gas turbine. The combustion tests proved that NOx levels as well as mechanical characteristics were well within the goals.

Dataset (partial) for the journal article Torbaghan, Shahab Shariat, et al. "Designing day-ahead multi-carrier markets for flexibility: Models and clearing algorithms." Applied Energy 285 (2021): 116390. https://doi.org/10.1016/j.apenergy.2020.116390 Historical electricity bids obtained from the website of GME, the Italian power exchange, cannot be redistributed and are not included in the present dataset.

The crucial role evaluation can play in the co-development of project design and its implementation will be addressed through the analysis of a case study, the Green Communities (GC) project, funded by the Italian Ministry of Environment within the EU Interregional Operational Program (2007-2013) "Renewable Energy and Energy Efficiency". The project's broader goals included an attempt to trigger a change in Italian local development strategies, especially for mountain and inland areas, which would be tailored to the real needs of communities, and based on a sustainable exploitation and management of the territorial assets. The goal was not achieved, and this paper addresses the issues of how GC could have been more effective in fostering a vision of change, and which design adaptations and evaluation procedures would have allowed the project to better cope with the unexpected consequences and resistances it encountered. The conclusions drawn are that projects should be conceived, designed and carried out as dynamic systems, inclusive of a dynamic and engaged evaluation enabling the generation of feedbacks loops, iteratively interpreting the narratives and dynamics unfolding within the project, and actively monitoring the potential of various relationships among project participants for generating positive social change.

Bioplastics are alternatives of conventional petroleum-based plastics. Bioplastics are polymers processed from renewable sources and are biodegradable. This study aims at conducting an environmental impact assessment of the bioprocessing of agricultural wastes into bioplastics compared to petro-plastics using an LCA approach. Bioplastics were produced from potato peels in laboratory. In a biochemical reaction under heating, starch was extracted from peels and glycerin, vinegar and water were added with a range of different ratios, which resulted in producing different samples of bio-based plastics. Nevertheless, the environmental impact of the bioplastics production process was evaluated and compared to petro-plastics. A life cycle analysis of bioplastics produced in laboratory and petro-plastics was conducted. The results are presented in the form of global warming potential, and other environmental impacts including acidification potential, eutrophication potential, freshwater ecotoxicity potential, human toxicity potential, and ozone layer depletion of producing bioplastics are compared to petro-plastics. The results show that the greenhouse gases (GHG) emissions, through the different experiments to produce bioplastics, range between 0.354 and 0.623 kg CO2 eq. per kg bioplastic compared to 2.37 kg CO2 eq. per kg polypropylene as a petro-plastic. The results also showed that there are no significant potential effects for the bioplastics produced from potato peels on different environmental impacts in comparison with poly-β-hydroxybutyric acid and polypropylene. Thus, the bioplastics produced from agricultural wastes can be manufactured in industrial scale to reduce the dependence on petroleum-based plastics. This in turn will mitigate GHG emissions and reduce the negative environmental impacts on climate change.

Abstract Economically harvesting energy from a microbial fuel cell (MFC), increasing its electrical power production, and developing its role as a practical energy supply, needs a low-cost and high-performance design of the MFC compartments. According to this strategy, a novel monolithic membrane electrode assembly (MEA) was fabricated and evaluated as an air–cathode in a single-chamber MFC (SCMFC). The MEA was made of bacterial cellulose (BC), conductive multi-walled carbon nanotubes (CNT), and nano-zycosil (NZ). BC, as a nano-celluloses with oxygen barrier property, can maintain anaerobic conditions for the anode compartment. Binder-less CNT coating on BC avoids costly binders such as poly-tetra fluoro ethylene (PTFE) and Nafion and decreases the MEA charge transfer resistance. NZ, as a very cheap modifier, not only prevents the anolyte leakage but also provides more MEA’s active sites for the oxygen reduction reaction (ORR). The electrochemical performance of the MEA was compared to a PTFE- based gas diffusion electrode (GDE) in the SCMFC. The MEA cell provided a pulse power density of 1790 mW/m2, roughly twice as high as the pulse power density of GDE (920 mW/m2). SCMFC’s internal resistance decreased from 1.84 KΩ (with GDE) to 0.8 KΩ (with MEA). Also, the cell’s columbic efficiency increased from 4.2% (with GDE) to11.7% (with MEA). Additionally, the capacitance of the MEA (65 mF) was much higher than the value for GDE (0.73 mF). Thus, the MEA compared to the GDE showed higher performance in the SCMFC for electricity generation and wastewater treatment at a lower cost.

AbstractAlthough the road-map of the oxy-fuel process seems to be very advanced, there are still plenty of open questions. One of the significant ones is the corrosive behaviour of the heat exchanger surfaces. The Institute of Combustion and Power Plant Technology, University of Stuttgart, performs research on the fireside corrosion under oxy-fuel and conventional combustion conditions for the current and supercritical power plants considering the influence of combustion modus, gas atmosphere and fly ash deposits on the waterwall and superheater surfaces. Since the oxy-fuel-combustion atmosphere is composed of recirculated flue gases and pure oxygen, significantly higher concentrations of CO2, SO2 and H2O are present compared to the conventional combustion of coal with air as an oxidizer. In the here presented study the influence of an oxy-fuel combustion of a hard-coal on the surface of selected superheater materials is discussed and compared to the results obtained for lignite. Especially the interactions between the flue gas atmosphere, ash deposits and heat exchanger materials are studied in detail. The investigation encompassed in this paper has been focused on impacts of oxide-scale growth, carbon enrichment of the materials and sulphur-induced corrosion.Increased sulphur-induced corrosion has been observed in samples exposed to the oxy-combustion atmosphere. The noticed higher depth of corrosive attack of the oxy-fuel samples might be explained by a higher partial pressure of SO2 which is characteristic for oxy-fuel process. Moreover in certain cases the sulphur might be released by the deposits. Beside that, the oxy-fuel samples were exposed to much higher partial pressures of carbon dioxide comparing to the air-case leading apparently to rapid and massive internal carbon enrichment in the oxide scale. Moreover dependence between the chromium content and oxidation ability of the austenitic materials surfaces was noticed under oxy-fuel conditions.

Abstract Thermal energy storage with phase change materials (PCM) provides high storage capacities in small temperature intervals. For the design of storage systems, the enthalpy curve of the used PCM has to be known with high precision. The T-History method has evolved to a widely used method for the measurement of the enthalpy as a function of temperature of PCM because of its simplicity and the advantage to be able to investigate larger sample volumes than typically used for differential scanning calorimeters. In order to ensure isothermal specimen during the measurement a thermal insulation is often mounted around the sample holder, but this insulation material is not considered in the evaluation model. In this work a new evaluation model for insulated T-History setups is developed by an analytical heat balance. This model is validated by numerical simulations of insulated T-History measurements and experimentally. By the use of the new model for the evaluation of the enthalpy a significant increase of accuracy can be achieved.