• Energy Research
• Closed Access close
• 7. Clean energy close
• 2. Zero hunger close
• DE close
• IT close

Abstract To achieve the EU climate and energy objectives, a transition towards a future sustainable energy system is needed. The integration of the huge potential for industrial waste heat recovery into smart energy system represents a main opportunity to accomplish these goals. To successfully implement this strategy, all the several stakeholders' conflicting objectives should be considered. In this paper an evolutionary multi-objective optimization model is developed to perform a sustainability evaluation of an energy system involving an industrial facility as the waste heat source and the neighbourhood as district heating network end users. An Italian case study of heat recovery from a steel casting facility shows how the model allows to properly select the district heating network set of users to fully exploit the available waste energy. Design directions such as the thermal energy storage capacity can be also provided. Moreover, the model enables the analysis of the trade-off between the stakeholders’ different perspectives, allowing to identify possible win-win solutions for both the industrial sector and the citizenship.

Abstract Breastshot water wheels are gravity hydraulic machines employed in low head sites. The scope of this work is to test the performance of a breastshot water wheel with two geometric inflow configurations: a sluice gate at different openings and two vertical overflow weirs. With the sluice gate, the maximum efficiency of the plant is 75%, constant over a wide range of flow rates, while the efficiency with the weir is increasing in the same flow rate range. Therefore, the wheel with the weir can exploit higher water volumes, and also it performs better at high power input. In practical applications, the inflow configuration can be effectively controlled to optimize the operative working conditions of breastshot water wheels, depending on the external hydraulic ones. The experimental results are also discussed in dimensionless terms, in order to support engineers in the design of similar breastshot water wheels.

Abstract Hybrid energy storage is a multi-modal approach to store and supply different forms of energy (electricity, heat, cold) simultaneously. This is an important sector coupling approach and enables large scale flexibility for a deep decarbonization of energy systems. Two different proposed energy storages – power-to-heat-to-X energy storage (PHXES) and pumped thermal energy storage (PTES) – are investigated in detail in this work towards their potential towards a hybrid deployment. The techno-economic analysis includes thermodynamic flowsheet simulations and unified cost estimations based on the used equipment. It is shown that the main input data set (e.g. working fluid selection, turbomachinery efficiency, pinch temperatures) has a strong influence on storage roundtrip efficiency in the thermodynamic simulations, but also on storage costs. Cost decrease and performance increase can be conflicting development targets, and it is not clear if future energy systems rather require technologies with the highest storage efficiencies or if low cost is an important prerequisite. PHXES and three variants of PTES are implemented into a simplified energy system model of the city of Hamburg that comprises the electric load and heat demand of the district heating system. Two scenarios (fossil benchmark and 80% decarbonization) are used to select the technologies and their capacities that allow the most cost-effective energy supply solution by a linear-programming optimization procedure. Large scale renewable power generation and hybrid energy storage play the major roles in the decarbonization scenario. PHXES with a storage capacity of 69 GWh, hot water storage (3.6 GWh) and a battery system (430 MWh) are part of the cost-optimal solution. A cost sensitivity analysis shows that a total cost reduction of 60–80% is required for PTES to become competitive in this model scenario.

Bioplastics are alternatives of conventional petroleum-based plastics. Bioplastics are polymers processed from renewable sources and are biodegradable. This study aims at conducting an environmental impact assessment of the bioprocessing of agricultural wastes into bioplastics compared to petro-plastics using an LCA approach. Bioplastics were produced from potato peels in laboratory. In a biochemical reaction under heating, starch was extracted from peels and glycerin, vinegar and water were added with a range of different ratios, which resulted in producing different samples of bio-based plastics. Nevertheless, the environmental impact of the bioplastics production process was evaluated and compared to petro-plastics. A life cycle analysis of bioplastics produced in laboratory and petro-plastics was conducted. The results are presented in the form of global warming potential, and other environmental impacts including acidification potential, eutrophication potential, freshwater ecotoxicity potential, human toxicity potential, and ozone layer depletion of producing bioplastics are compared to petro-plastics. The results show that the greenhouse gases (GHG) emissions, through the different experiments to produce bioplastics, range between 0.354 and 0.623 kg CO2 eq. per kg bioplastic compared to 2.37 kg CO2 eq. per kg polypropylene as a petro-plastic. The results also showed that there are no significant potential effects for the bioplastics produced from potato peels on different environmental impacts in comparison with poly-β-hydroxybutyric acid and polypropylene. Thus, the bioplastics produced from agricultural wastes can be manufactured in industrial scale to reduce the dependence on petroleum-based plastics. This in turn will mitigate GHG emissions and reduce the negative environmental impacts on climate change.

Abstract Economically harvesting energy from a microbial fuel cell (MFC), increasing its electrical power production, and developing its role as a practical energy supply, needs a low-cost and high-performance design of the MFC compartments. According to this strategy, a novel monolithic membrane electrode assembly (MEA) was fabricated and evaluated as an air–cathode in a single-chamber MFC (SCMFC). The MEA was made of bacterial cellulose (BC), conductive multi-walled carbon nanotubes (CNT), and nano-zycosil (NZ). BC, as a nano-celluloses with oxygen barrier property, can maintain anaerobic conditions for the anode compartment. Binder-less CNT coating on BC avoids costly binders such as poly-tetra fluoro ethylene (PTFE) and Nafion and decreases the MEA charge transfer resistance. NZ, as a very cheap modifier, not only prevents the anolyte leakage but also provides more MEA’s active sites for the oxygen reduction reaction (ORR). The electrochemical performance of the MEA was compared to a PTFE- based gas diffusion electrode (GDE) in the SCMFC. The MEA cell provided a pulse power density of 1790 mW/m2, roughly twice as high as the pulse power density of GDE (920 mW/m2). SCMFC’s internal resistance decreased from 1.84 KΩ (with GDE) to 0.8 KΩ (with MEA). Also, the cell’s columbic efficiency increased from 4.2% (with GDE) to11.7% (with MEA). Additionally, the capacitance of the MEA (65 mF) was much higher than the value for GDE (0.73 mF). Thus, the MEA compared to the GDE showed higher performance in the SCMFC for electricity generation and wastewater treatment at a lower cost.

Abstract Thermal energy storage with phase change materials (PCM) provides high storage capacities in small temperature intervals. For the design of storage systems, the enthalpy curve of the used PCM has to be known with high precision. The T-History method has evolved to a widely used method for the measurement of the enthalpy as a function of temperature of PCM because of its simplicity and the advantage to be able to investigate larger sample volumes than typically used for differential scanning calorimeters. In order to ensure isothermal specimen during the measurement a thermal insulation is often mounted around the sample holder, but this insulation material is not considered in the evaluation model. In this work a new evaluation model for insulated T-History setups is developed by an analytical heat balance. This model is validated by numerical simulations of insulated T-History measurements and experimentally. By the use of the new model for the evaluation of the enthalpy a significant increase of accuracy can be achieved.

Abstract This article focuses on the results obtained by the enforcement of a original greenhouse gas emissions policy, issued in recent years in several municipalities in Northern Italy. The Municipality of Reggio Emilia was one of the firsts in Italy to develop and adopt a voluntary building energy-consumption certification method called Ecoabita, aiming to promote energy efficiency in buildings over its jurisdiction. Several reasons make this project innovative: first, the certification method has been processed through and verified by a quality international agency, secondly the procedure is assisting financial-incentive policies both on mandatory (European Directive 2002/91/CE) and voluntary basis (Municipality Protocol Ecoabita), finally it allows to obtain eligible credits for avoided emissions that can be negotiated on the CO2 exchange market. With specific reference to Reggio Emilia case, acknowledged the amount of actions, that are normally scheduled in the municipality throughout a year, it has been evaluated the benefit, in terms of environmental improvement, descended from the protocol, also projecting their trend in future years up to 2020 as well, demonstrating the scheduled interventions are fundamental in sought of the achievement of the Kyoto and Copenhagen commitments. The entire procedure has been developed in accordance to the parameters given by UNFCCC for these kinds of analyses and has been recently confirmed to be one of the most accurate international accounting procedure by a survey developed by the scientific committee of the European Project LIFE-LAKS.

Abstract Probability density functions (PDFs) are normally used to describe wind speed distribution for the proper selection of wind turbines in a given location. The identification of a suitable PDF is fundamental for accurately assessing the wind energy potential and designing the wind farms. To achieve this objective, the use of a mixture of two truncated normal distributions (MTTND), defined for v ≥ 0 and obtained by linearly combining two normal distributions with different means and variances, is proposed in this work for the representation of the wind speed PDF. The distribution is a function of five parameters, does not require a high computational burden and allows the representation of wind calm hours (v = 0). The use of the MTTND allows an accurate estimation to be obtained of the experimental discrete distribution of the probability density and cumulative probability, and the characteristic statistical quantities used to estimate the available energy and the performance indicators in the selection of both the site and wind turbine. The validity of the use of the MTTND was verified by comparison with the most widespread PDFs in the scientific literature: Weibull, Rayleigh, lognormal, gamma, inverse Gaussian and Burr. This comparison was developed using experimental wind speed data relating to five Italian locations and a location in Colorado (USA) belonging to the National Renewable Energy Laboratory. For each location, the parameters of each PDF were obtained with the least squares non-linear regression method. The results of the comparisons, in terms of the coefficient of determination R2 and root mean square error (RMSE) for goodness of fit and in terms of relative error in the calculation of the statistical quantities, show that the use of the MTTND gives rise to greater accuracy than a conventional wind speed PDF.

Abstract Reaching universal access to electricity by 2030 requires a massive deployment of mini-grids in rural areas of developing countries. Among the many challenges hindering this process, there are the high uncertainties in assessing demand patterns in rural communities, the costs of field survey campaigns, and the absence of ample and reliable datasets coming from existing projects. This paper tries to address these issues by presenting and discussing a database of load profiles from sixty-one off-grid mini-grids from developing countries worldwide, gathered from the literature, private developers and fieldworks, and reported with technical, socio-economic and geographical characterization factors. A clustering procedure led to the identification of five archetypal load profile clusters, which are presented and analyzed together with their load duration curves. Subsequently, the distribution among the clusters of the various characterization factors selected is studied. The proposed approach allows to widen the range of load profiles usually considered, and to seek correlations between the load profile shapes, the peak power and average energy consumption per connection, the number of customers, the age of measurement, geographical position, operator model, type of tariff and generation technologies present. This work establishes a first step in the creation of a shared database for load profiles of rural mini-grids, helping to overcome the lack of available data and difficulties of demand assessment, proposing original insights for researchers to understand load patterns, and contributing to reduce risks and uncertainties for mini-grid developers.