• Energy Research
• 2016-2025close
• 7. Clean energy close
• 8. Economic growth close
• US close
• ES close

Abstract Dimethyl ether appears to be a better choice among various diesel alternatives due to its high cetane number and sootless combustion. However, the physical and chemical properties of dimethyl ether are very different from those of diesel. The physical properties influence spray formation and atomization characteristics, while chemical properties determine combustion and emission formation characteristics. Thus, fuel's physical and chemical properties significantly determine engine performance and emissions. In the present work, spray combustion and emission formation characteristics of n-heptane, dimethyl ether, and their blends (10, 25, and 50% dimethyl ether in n-heptane) were numerically studied in a constant volume chamber. Results show that the n-heptane spray combustion has the highest heat release rate with an intense premix combustion phase, whereas dimethyl ether spray combustion has the lowest heat release rate and shortest premix combustion phase. The magnitude of the premixed phase and heat release rate decreases with the increase in dimethyl ether mass fraction in the blends. Soot, carbon monoxide (CO), unburned hydrocarbon (UHC), and nitric oxide (NO) emissions decreased with the increase in the dimethyl ether mass fraction in the blends and were lowest for the dimethyl ether.

Construction involves the use of significant quantities of raw materials and entails high-energy consumption. For the sake of choosing the most appropriate solution that considers environmental and sustainable concepts, tools such as the integrated value model for sustainable assessment (Modelo Integrado de Valor para una Evaluación Sostenible, MIVES) used in Spain, plays a key role in obtaining the best solution. MIVES is a multi-criteria decision-making method based on the value function concept and the seminars delivered by experts. Such tools, in order to show how they may work, require application to case studies. In this paper, two concrete slabs manufactured with differing reinforcements during the construction of the La Canda Tunnels are compared by means of MIVES. The two concrete slabs were reinforced with a conventional steel-mesh and with polyolefin fibres. This research was focussed on the main aspects affecting the construction. That is to say, the environmental, economic, and social factors were assessed by the method, being of special impact the issues related with maintenance of the structure. The results showed that from the point of view of sustainability, the use of polyolefin fibres provided a significant advantage, mainly due to the lower maintenance required.

Given the considerable scale of distribution networks in urban and rural areas, as well as the lack of management records, adjustments of switches during the distribution system operation are poorly documented. Such deficiency results in the inaccuracy of models stored in the distribution network automation system, and thus misleads the state estimation. With the emergence of information and communication technology, a large number of the feeder and residential smart meter data are accumulated. Such data can help recognize the operation modes of distribution networks by analyzing the relationships between the on/off states of switches and the voltage correlations among buses. However, the limited quantity and quality of the sampling data restrict the implementation of data-driven recognition. In this paper, a physical-probabilistic-network (PPN) model applied for inferring overall operation mode of distribution networks is proposed. Based on which, a belief propagation-based algorithm is proposed for the inference even under situations when there are only partial bus voltages data available. Meanwhile, the required variable for inference can be reduced from the active trail analysis. Experiment results are used to compare its performance with classic methods and to prove its effectiveness and advantages.

Abstract Heat pipes and two-phase thermosyphons are highly efficient heat transfer devices utilizing continuous evaporation and condensation of working fluid for two-phase heat transport in closed systems. Because of the nearly isothermal and fully passive phase-change heat transfer mechanism, heat pipes and thermosyphons have found many applications in nuclear engineering, space technologies, and other energy systems. High-temperature heat pipes are used in nuclear microreactors to remove fission power from the primary system and are coupled with power conversion systems or process heat applications. Modeling of the two-phase flow phenomena inside a heat pipe is essential to its design and safety analysis. In this study, a comprehensive one-dimensional two-phase three-field flow model has been developed for the analysis of heat pipes in normal operation conditions and transients. The conservation or field equations of mass, momentum, and energy were developed for the liquid film, vapor, and droplet. In addition, constitutive models or correlations were reviewed thoroughly and provided for the closure of the three-field equations. Specific constitutive equations regarding interfacial mass and heat transfer at two interfaces, namely film-gas interface and gas-droplet interface, were reviewed for droplet entrainment and deposition rates as well as film and droplet evaporation rates. Additionally, mechanistic correlations of annular flow film thickness were recommended for the modeling of the thermosyphons without a wick as a critical constitutive correlation. Furthermore, experimental data needs from new experiments using a prototype working fluid or surrogate fluids for the model validation of high-temperature heat pipes in microreactors were recommended for future research.

Sustainable electricity generation is one of the major current challenges for our society. In this context, the evolution of nanomaterials and nanotechnologies has enabled the fabrication of microscopic devices to produce clean energy from a great variety of renewable sources. To expand the possibilities of energy generation, we have designed and fabricated bioinorganic generators capable to produce electricity by conversion of chemical energy from renewable fuel sources. Unlike traditional generators, the systems described herein produce mechanical energy through enzyme-driven gas production which generates vibration and pressure that are thus converted into electricity by the action of a piezoelectric component properly integrated into the device. Our generators are able to produce an electric ernergy from different renewable sources like glucose, ethanol, and amino acids, attaining energy outputs around 250 nJ cm–2 and reaching maximum open-circuit voltages of up to 1 V. In addition, the produced energy can be easily regulated by adjusting both enzyme and fuel concentration which can tune the electrical output according to the application. The systems described herein propose a new concept for self-sufficient energy harvesting that bridges biocatalysis and piezoelectricity, where the energy production is based on the piezoelectric effect triggered by enzymatic action rather than on the enzyme-driven electron transfer that governs biofuel cells. Although the electric output is too low yet to be considered an alternative for energy production, this technology opens the door to power small devices. We envision the utilization of this technology in such remote locations where mechanical energy is lacking but there are chemical energy reservoirs. We would like to acknowledge Marie-Curie Actions (NANOBIENER project), IKERBASQUE foundation for funding F.L.-G., and the support of COST Action CM1303 Systems Biocatalysis. We also acknowledge HERGAR foundation for the funding. Peer reviewed

Abstract This paper uses research-quality, ground measurements of irradiance and temperature that are accurate to ±2% to estimate the electric energy yield of fixed solar modules for utility-scale solar power plants at 18 sites in Saudi Arabia. The calculation is performed for a range of tilt and azimuth angles and the orientation that gives the optimum annual energy yield is determined. A detailed analysis is presented for Riyadh including the impact of non-optimal tilt and azimuth angles on annual energy yield. It is also found that energy yield in March and October are higher than in April and September, due to milder operating temperatures of the modules. A similar optimization of tilt and azimuth is performed each month separately. Adjusting the orientation each month increases energy yield by 4.01% compared to the annual optimum, but requires considerable labour cost. Further analysis shows that an increase in energy yield of 3.63% can be obtained by adjusting the orientation at five selected times during the year, thus significantly reducing the labour requirement. The optimal orientation and corresponding energy yield for all 18 sites is combined with a site suitability analysis taking into account climate, topography and proximity to roads, transmission lines and protected areas. Six sites are selected as having high suitability and high energy yield: Albaha, Arar, Hail, Riyadh, Tabuk and Taif. For these cities the optimal tilt is only slightly higher than the latitude, however the optimum azimuth is from 20° to 53° west of south due to an asymmetrical daily irradiance profile.

As the concern with global warming increases causing the need for CO2 reduction, renewable energy is of great interest as it has lower carbon footprint when compared to conventional sources (natural gas, coal, oil and nuclear). Solar energy has been drawing worldwide attention since it can transform sunlight directly into electricity with the use of photovoltaic (PV) cells. However, this technology has some drawbacks that need to be addressed including dust deposition on solar panels, also known as soiling. Soiling can decrease PV panel's efficiency thereby resulting in less energy production. The soiling rates are very site specific and depend on the geographic location of the panels and the climate in that area. The solar panels can be cleaned naturally (by rainfall, snow or wind) or mechanically washed. This thesis addresses the impact of solar panel soiling and washing on the energy production of solar PV plants located at the UNLV campus. The objectives of this project were (a) to evaluate whether rainfall alone, in the desert environment with low rainfall, is sufficient to clean up the solar panels, and, if possible, determine the minimum amount of rainfall necessary to clean up panels.; (b) to examine the efficiency loss caused by soiling using different methods of analyses and (c) to evaluate if panel washing is worthwhile given the cost and the efficiency gain that is obtained by washing. To calculate the efficiency of the panels, a model was developed to generate parameters that were not measured at the site. Panel efficiencies before and after rainfall events were compared to determine the minimum amount of rain necessary to clean the panels. It was found that at least 0.2 inches of rain was needed to partially restore clean-panel efficiency. In Las Vegas, the recurrence periods of different depths rainfall were calculated using data from the past 29 years. It was observed that the 50th percentile recurrence period of a rainfall event with depth of 0.2 inches or higher was approximately 52 days. Student Union: -0.0044%/day, CBC-C: -0.00099%/day, and Dayton Hall: -0.0034%/day The amount of efficiency lost during the dry intervals (periods between rainfall events) was analyzed in three different ways. The average efficiency loss per day during the dry periods varied from -0.000171 % to -0.00533 %, depending on the method used and the building where the panels were located. However, there were some limitations to the calculations. It was not possible to completely isolate the effects of only soiling on the efficiency of the panels. The rate of decline seemed to be also impacted by seasonal effects. To better evaluate the effect of washing, a professional company was hired to wash a set of solar panels located on UNLV's Student Union building. The panels were washed with water with a low concentration of TDS. The power output and the efficiency of those panels were analyzed from before and after the washing. There was a very small efficiency and power increase due to the washing. Therefore, it was concluded that washing in this area is not worthwhile, and that rainfall events in excess of 0.2 inches can adequately restore the efficiency of the panels. If there is a change in cost of energy, washing, water or a great increase in the efficiency of the solar panels, it would be necessary to reevaluate the analysis.

Abstract Adsorbent-based carbon capture is only feasible if adsorption-desorption cycles are both fully regenerating and efficient. This work proposes a regenerative pH swing process and a pH swing regenerative adsorbent that are inspired by natural CO2 conversion by carbonic anhydrase biocatalysts found in mammalian red blood cells. The main objective is to develop, test and analyze a synthetic pH Swing Adsorption (pHSA) system as well as a pHSA compatible solid adsorbent to capture CO2 from a simulated ambient air gas stream. The lead developed adsorbent is a carbon black co-activated with potassium carbonate and nitrogenous copolymer that is impregnated with immobilized bovine carbonic anhydrase and thereby deemed “BCA/KN-CB”. BCA/KN-CB has preliminarily demonstrated both competitive CO2 adsorption capacity and limited regenerative ability under experimental pHSA conditions. In addition, BCA-based adsorbents achieved higher adsorption capacities than non-BCA adsorbent counterparts. The BCA/KN-CB adsorbent displayed both large point of zero charge (PZC) swings and regenerative stability. The proposed pHSA system requires essentially zero energy expenditure to achieve intended environments for capture and regeneration. With 1 kg of adsorbent, pHSA has the ability to capture 1 kg CO2 in less than 4 h of cycling. The tested pHSA adsorbent can also capture more than 96% of total CO2 in a given raw gas stream flowing through the capture chamber. This proof-of-concept study of a pH swing adsorption/biocatalytic adsorbent system suggests the potential to effectively operate under ambient conditions and exhibit advantageous operational efficiencies to other high-profile CO2 capture systems.