• Energy Research
• 12. Responsible consumption close
• 3. Good health close
• ES close
• Spanish National Research Council close

Sustainable electricity generation is one of the major current challenges for our society. In this context, the evolution of nanomaterials and nanotechnologies has enabled the fabrication of microscopic devices to produce clean energy from a great variety of renewable sources. To expand the possibilities of energy generation, we have designed and fabricated bioinorganic generators capable to produce electricity by conversion of chemical energy from renewable fuel sources. Unlike traditional generators, the systems described herein produce mechanical energy through enzyme-driven gas production which generates vibration and pressure that are thus converted into electricity by the action of a piezoelectric component properly integrated into the device. Our generators are able to produce an electric ernergy from different renewable sources like glucose, ethanol, and amino acids, attaining energy outputs around 250 nJ cm–2 and reaching maximum open-circuit voltages of up to 1 V. In addition, the produced energy can be easily regulated by adjusting both enzyme and fuel concentration which can tune the electrical output according to the application. The systems described herein propose a new concept for self-sufficient energy harvesting that bridges biocatalysis and piezoelectricity, where the energy production is based on the piezoelectric effect triggered by enzymatic action rather than on the enzyme-driven electron transfer that governs biofuel cells. Although the electric output is too low yet to be considered an alternative for energy production, this technology opens the door to power small devices. We envision the utilization of this technology in such remote locations where mechanical energy is lacking but there are chemical energy reservoirs. We would like to acknowledge Marie-Curie Actions (NANOBIENER project), IKERBASQUE foundation for funding F.L.-G., and the support of COST Action CM1303 Systems Biocatalysis. We also acknowledge HERGAR foundation for the funding. Peer reviewed

Abstract Hybrid TiO2/SiO2 thin films deposited by material printing technique on flexible substrates were prepared, characterized and tested for solar photocatalytic disinfection. Effect of surface hydrophilicity/hydrophobicity of printed coatings on photocatalytic disinfection was studied by means of (i) drinking water contaminated with natural consortia of fecal bacteria (gram-negative: Escherichia coli and total coliforms; gram-positive: Enterococci), and (ii) seawater containing pathogenic gram-negative bacteria (Vibrio owensii, Vibrio alfacsensis and Vibrio harveyi). Inactivation of gram-negative bacteria in drinking water with fecal contamination by solar photocatalysis was slightly more efficient than solar disinfection, while for gram-positive bacteria similar efficiency was observed. These results, in combination with observed release of titanium from coatings (detected by means of inductively coupled plasma atomic emission spectrometer), indicate that TiO2/SiO2 needs further improvements for solar photocatalytic disinfection of drinking water. Efficiency of seawater disinfection towards gram-negative Vibrio spp. (Vibrio owensii, Vibrio alfacsensis and Vibrio harveyi) was significantly enhanced when TiO2/SiO2 coatings were used under natural solar light. Moreover, hydrophobic thin films led to faster Vibrio spp. inactivation as compared to hydrophilic ones, which was attributed to higher bacteria adhesion on hydrophobic coatings. However, decrease of photocatalytic activity of hydrophobic TiO2/SiO2 coatings was observed after ten experimental cycles mainly due to deposition of salts on the surface of photocatalyst. Generally, results of this study suggest that autochthonous bacteria such as Vibrio spp. in seawater are significantly more resistant to solar disinfection in comparison with not autochthonous bacteria such as Escherichia coli, total coliforms and Enterococci in contaminated drinking water.

The objective of this paper is to explain novel sustainable robotics solutions for cities. Those new proposals appear under the ECHORD++ project which is a good tool to meet academia and industry with the objective of providing innovative technological solutions. In this paper, authors explain the tool as well as the methodology to promote robotics research in urban environments, and the on-going experience will demonstrate that huge advances are made in this field. Peer Reviewed

Access to reliable and affordable energy is vital for sustainable development. In the off-grid areas of developing countries, decentralized energy solutions have received increasing attention due to their contributions to reducing poverty. However, most of the rural population in many developing countries still has little or no access to modern energy technologies. This paper assesses the factors that determine the successes and failures of decentralized energy solutions based on local harmonized case studies from heterogeneous contexts from Asia, sub-Saharan Africa, and South America. The case studies were analyzed through the coupled lenses of energy transition and the Water–Energy–Food Security (WEF) Nexus. The findings indicate that access to modern decentralized energy solutions has not resulted in complete energy transitions due to various tradeoffs with the other domains of the WEF Nexus. On the other hand, the case studies point at the potential for improvements in food security, incomes, health, the empowerment of women, and resource conservation when synergies between decentralized energy solutions and other components of the WEF Nexus are present.

Alkali activation is a highly active and rapidly developing field of activity in the global research and development community. Commercial-scale deployment of alkali-activated cements and concretes is now proceeding rapidly in multiple nations. This paper reviews the key developments in alkali-activated materials since 2011, with a particular focus on advances in characterisation techniques and structural understanding, binder precursors and activation approaches, durability testing and design, processing, and sustainability. The scientific and engineering developments described in this paper have underpinned the on-going scale-up activities. We also identify important needs for future research and development to support the optimal and appropriate utilisation of alkali activated materials as a component of a sustainable future construction materials industry. The contributions of JLP were supported by the European Research Council 7th Framework Programme, through the Starting Grant “GeopolyConc” (StG-335928), those of C. Shi were supported by the National Natural Science Foundation of China under contract Nos. U1305243 and 51378196.