• Energy Research
• 7. Clean energy close
• EU close
• AT close

This paper is devoted to study the electrochemical behavior of Pt catalyst in a polymer electrolyte fuel cell at various operating conditions and at different electric potential difference (also known as voltage) cycling applied in accelerated stress tests. The degradation of platinum is considered with respect to the Pt ion dissolution and the Pt oxide coverage of catalyst described by a one-dimensional model. In the model, degradation rate increases with temperature and decreasing particle diameter of Pt nano-particles. The theoretical study of the underlying diffusion system with the nonlinear reactions is presented by analytical methods and gives explicit solutions through a first integral of the ODE system. Numerical tests are obtained using a second order implicit-explicit scheme. The computer simulation shows that the lifetime of the catalyst depends on the voltage profile and the upper potential level. By this Pt mass loss is more significant at the membrane surface than at the gas diffusion layer.

This paper is devoted to study the electrochemical behavior of Pt catalyst in a polymer electrolyte fuel cell at various operating conditions and at different electric potential difference (also known as voltage) cycling applied in accelerated stress tests. The degradation of platinum is considered with respect to the Pt ion dissolution and the Pt oxide coverage of catalyst described by a one-dimensional model. In the model, degradation rate increases with temperature and decreasing particle diameter of Pt nano-particles. The theoretical study of the underlying diffusion system with the nonlinear reactions is presented by analytical methods and gives explicit solutions through a first integral of the ODE system. Numerical tests are obtained using a second order implicit-explicit scheme. The computer simulation shows that the lifetime of the catalyst depends on the voltage profile and the upper potential level. By this Pt mass loss is more significant at the membrane surface than at the gas diffusion layer.

Using liquid metals confined in capillary porous structures (CPSs) as a plasma-facing component (PFC) could prolong the lifetime of the divertor in the high heat flux area. However, the high atomic number of tin (Sn) limits its acceptable fraction in the main plasma. Therefore, a crucial step in developing this concept is to test it in a tokamak environment, particularly in the diverted plasma region, e.g. ASDEX Upgrade (AUG). In this paper, the design of liquid tin module (LTM) is explained, and the testing in the high heat flux device GLADIS before its use in AUG is presented. The LTM was additively manufactured using selective laser melting, consisting of a 1.5mm porous layer tungsten (W) directly attached to a solid W bulk. The LTM has a plasma-facing area of 16×40mm2 and was filled with 1.54g of Sn. In GLADIS, the module was exposed to power loads between 2 and 8MWm−2 for 1 up to 10s, first unfilled and later filled with Sn. The surface temperature was monitored with infrared imaging and pyrometry. The thermal response was used to compare with simulations in Ansys Mechanical, enabling a determination of the module’s effective thermal properties. Sn droplets could be observed on the infrared camera, until a surface temperature of about a 1000°C was reached. The enhanced wetting of tin on the plasma-facing surface, which was observed by a visible camera, suggests that there is a conditioning of the surface, possibly due to the removal of impurities and oxides. Subsequent examinations of the adjacent tile revealed minor Sn leakages emanating from the module’s edge. Furthermore, the module showed no indication of mechanical failure. Therefore, these results indicated that the LTM qualifies for the heat fluxes expected in ASDEX Upgrade.

Using liquid metals confined in capillary porous structures (CPSs) as a plasma-facing component (PFC) could prolong the lifetime of the divertor in the high heat flux area. However, the high atomic number of tin (Sn) limits its acceptable fraction in the main plasma. Therefore, a crucial step in developing this concept is to test it in a tokamak environment, particularly in the diverted plasma region, e.g. ASDEX Upgrade (AUG). In this paper, the design of liquid tin module (LTM) is explained, and the testing in the high heat flux device GLADIS before its use in AUG is presented. The LTM was additively manufactured using selective laser melting, consisting of a 1.5mm porous layer tungsten (W) directly attached to a solid W bulk. The LTM has a plasma-facing area of 16×40mm2 and was filled with 1.54g of Sn. In GLADIS, the module was exposed to power loads between 2 and 8MWm−2 for 1 up to 10s, first unfilled and later filled with Sn. The surface temperature was monitored with infrared imaging and pyrometry. The thermal response was used to compare with simulations in Ansys Mechanical, enabling a determination of the module’s effective thermal properties. Sn droplets could be observed on the infrared camera, until a surface temperature of about a 1000°C was reached. The enhanced wetting of tin on the plasma-facing surface, which was observed by a visible camera, suggests that there is a conditioning of the surface, possibly due to the removal of impurities and oxides. Subsequent examinations of the adjacent tile revealed minor Sn leakages emanating from the module’s edge. Furthermore, the module showed no indication of mechanical failure. Therefore, these results indicated that the LTM qualifies for the heat fluxes expected in ASDEX Upgrade.

The agro-livestock sector produces about one third of global greenhouse gas (GHG) emissions. Since more energy is needed to meet the growing demand for food and the industrial revolution in agriculture, renewable energy sources could improve access to energy resources and energy security, reduce dependence on fossil fuels, and reduce GHG emissions. Hydrogen production is a promising energy technology, but its deployment in the global energy system is lagging. Here, we analyzed the theoretical and practical application of green hydrogen generated by electrolysis of water, powered by renewable energy sources, in the agro-livestock sector. Green hydrogen is at an early stage of development in most applications, and barriers to its large-scale deployment remain. Appropriate policies and financial incentives could make it a profitable technology for the future.

The agro-livestock sector produces about one third of global greenhouse gas (GHG) emissions. Since more energy is needed to meet the growing demand for food and the industrial revolution in agriculture, renewable energy sources could improve access to energy resources and energy security, reduce dependence on fossil fuels, and reduce GHG emissions. Hydrogen production is a promising energy technology, but its deployment in the global energy system is lagging. Here, we analyzed the theoretical and practical application of green hydrogen generated by electrolysis of water, powered by renewable energy sources, in the agro-livestock sector. Green hydrogen is at an early stage of development in most applications, and barriers to its large-scale deployment remain. Appropriate policies and financial incentives could make it a profitable technology for the future.