• Energy Research
• Open Access close
• Embargo close
• other engineering and technologies close
• FR close
• EU close

AbstractDecarbonising the energy system requires high shares of variable renewable generation and sector coupling like power to heat. In addition to heat supply, heat pumps can be used in future energy systems to provide flexibility to the electricity system by using the thermal storage potential of the building stock and buffer tanks to shift electricity demand to hours of high renewable electricity production. Bridging the gap between two methodological approaches, we coupled a detailed building technology operation model and the open-source energy system model Balmorel to evaluate the flexibility potential that decentral heat pumps can provide to the electricity system. Austria in the year 2030 serves as an example of a 100% renewable-based electricity system (at an annual national balance). Results show that system benefits from heat pump flexibility are relatively limited in extent and concentrated on short-term flexibility. Flexible heat pumps reduce system cost, CO2 emissions, and photovoltaics and wind curtailment in all scenarios. The amount of electricity shifted in the assessed standard flexibility scenario is 194 GWhel and accounts for about 20% of the available flexible heat pump electricity demand. A comparison of different modelling approaches and a deterministic sensitivity analysis of key input parameters complement the modelling. The most important input parameters impacting heat pump flexibility are the flexible capacity (determined by installed capacity and share of control), shifting time limitations, and cost assumptions for the flexibility provided. Heat pump flexibility contributes more to increasing low residual loads (up to 22% in the assessed scenarios) than decreasing residual load peaks. Wind power integration benefits more from heat pump flexibility than photovoltaics because of the temporal correlation between heat demand and wind generation.

The energy considered as waste heat in industrial furnaces owing to inefficiencies represents a substantial opportunity for recovery by means of thermal energy storage (TES) implementation. Although conventional systems based on sensible heat are used extensively, these systems involve technical limitations. Latent heat storage based on phase change materials (PCMs) results in a promising alternative for storing and recovering waste heat. Within this scope, the proposed PCM-TES allows for demonstrating its implementation feasibility in energy-intensive industries at high temperature range. The stored energy is meant to preheat the air temperature entering the furnace by using a PCM whose melting point is 885 °C. In this sense, a heat transfer model simulation is established to determine an appropriate design based on mass and energy conservation equations. The thermal performance is analysed for the melting and solidification processes, the phase transition and its influence on heat transference. Moreover, the temperature profile is illustrated for the PCM and combustion air stream. The obtained results prove the achievability of very high temperature levels (from 700 to 865 °C) in the combustion air preheating in a ceramic furnace; so corroborating an energy and environmental efficiency enhancement, compared to the initial condition presenting an air outlet at 650 °C.

We present the architecture and design of the IANOS scheduling framework. The goal of the new Grid scheduling system is to provide a general job submission framework allowing optimal positioning and scheduling of HPCN applications. The scheduling algorithms used to calculate best-suited resources are based on an objective cost function that exploits information on the parameterization of applications and resources. This standard-based, interoperable scheduling framework comprises four general web services and three modules. The middleware is complemented with one client and one admin console. The implementation is based on proposed Grid and Web services standards (WSRF, WS-Agreement, JSDL, and GLUE). It is agnostic to a specific Grid middleware. The beta version of IANOS has been tested and integrated with UNICORE. The validation of IANOS is in progress by running different types of HPCN applications on a large-scale Grid testbed.

Abstract In this paper, a general mathematical model for the dynamic simulation of a single-effect LiBr/water absorption chiller is presented. The model is based on mass and energy balances applied to the internal components of the machine, and it accounts for the non-steady behaviour due to thermal and mass storage in the components. The validation of the mathematical model is performed through experimental data collected on a commercial small-capacity water-cooled unit. Due to the peculiar technology adopted in the real chiller, a special effort was made to identify the appropriate values of the main physical parameters. The validation of the model is based on the values of the water temperature at the outlet of the machine, as no measurement inside the machine was possible; anyway, a consistency analysis applied to the internal parameters is also presented. The agreement between experimental and simulated results is very good, both on a daily and on a seasonal basis.

Sustainability of agro-food supply chains has recently become the subject of greater interest from consumers, firms, governmental organizations and academia as the environment continues to deteriorate. One of the most critical factors influencing the sustainability of an agro-food supply chain is its network design. A particularly challenging aspect in this context is the broad range of influencing indicators associated with the Triple Bottom Line (TBL) of sustainability that need to be considered. However, many of these indicators could not be fully integrated or measured by single-step optimization problems. This paper presents a critical literature review of operational research methods for the design of sustainable supply chains. A novel two-stage hybrid solution methodology is proposed. In the first stage, a partner selection is performed using a hybrid multi criteria decision making based on Analytic Hierarchy Process (AHP) method and the Ordered Weighted Averaging (OWA) aggregation method. The result obtained in the first stage is used in the second stage to develop a multi-objective mathematical model to optimize the design of the supply chain network. This approach allows the simultaneous consideration of all three dimensions of sustainability including carbon footprint, water footprint, number of jobs created and the total cost of the supply chain design. The proposed approach generates a Pareto frontier to aid users in making decisions. Numerical experiments are completed utilizing data from an agro-food company to demonstrate the efficiency and effectiveness of the proposed solution methodology. The analyzes of the numerical results provide important organizational, practical and policy insights on (1) the impact of financial and environmental sustainability on supply chain network design (2) the tradeoff analysis between environmental emission, water footprint, societal implications and associated cost for making informed decision on supply chain investment.

The movement of the powdery material occurs in a multi-phase non-uniform electrostatic field at determined values of the voltage and the frequency, using travelling wave technique. This technique was applied for very small particles such as bacteria and other similar particle size. The objective of this work is to analyze the movement of PVC micronized particles and the feasibility of the separation of PVC/copper granular mixture of average size 100 μm. Two-phase and three-phase conveyors, which are supplied by high voltage amplifiers controlled by digital function generators, have been the subject of a parametric experimental investigation. Several factors were analyzed such as the voltage level up to 1400 V, the frequency, the phase shift and the number of phases of the conveyor. The obtained results showed that depending on the values of the above factors: i) the micronized particles can move instantly right after switching the conveyor, ii) the particles move towards one direction or the other of the conveyor iii) the separation of a granular mixture of plastic and copper micronized particles is possible.

AbstractSmart Grids are electrical grids that require a decentralised way of controlling electric power conditioning and thereby control the production and distribution of energy. Yet, the integration of Distributed Renewable Energy Sources (DRESs) in the Smart Grid introduces new challenges with regards to electrical grid balancing and storing of electrical energy, as well as additional monetary costs. Furthermore, the future smart grid also has to take over the provision of Ancillary Services (ASs). In this paper, a distributed ICT infrastructure to solve such challenges, specifically related to ASs in future Smart Grids, is described. The proposed infrastructure is developed on the basis of the Smart Grid Architecture Model (SGAM) framework, which is defined by the European Commission in Smart Grid Mandate M/490. A testbed that provides a flexible, secure, and low-cost version of this architecture, illustrating the separation of systems and responsibilities, and supporting both emulated DRESs and real hardware has been developed. The resulting system supports the integration of a variety of DRESs with a secure two-way communication channel between the monitoring and controlling components. It assists in the analysis of various inter-operabilities and in the verification of eventual system designs. To validate the system design, the mapping of the proposed architecture to the testbed is presented. Further work will help improve the architecture in two directions; first, by investigating specific-purpose use cases, instantiated using this more generic framework; and second, by investigating the effects a realistic number and variety of connected devices within different grid configurations has on the testbed infrastructure.