• Energy Research
• Closed Access close
• engineering and technology close
• GB close
• AE close

Abstract A CFD modelling study has been undertaken to examine the co-firing of pulverised coal and biomass with particular regard to the burnout of the larger diameter biomass particles. Computations were based on a research combustion facility that replicates an industrial coal-fired power station. Three percent, by mass, of pinewood was blended with a bituminous UK coal, and the effects of the wood particle size and shape on the burnout of the combined wood and coal char were investigated. The effect of varying the devolatilisation and char combustion rate constants for the biomass component in the blend was also investigated. It was concluded that the combustion of small (200 μm) wood particles was rapid but the rate of combustion of larger particles was dependent on their composition, size, and shape.

The Severn Estuary has the world's second largest tide range and a barrage across the estuary, located just seawards of Cardiff in Wales and Weston in the South West England, has been proposed for over half a century, with the objective of extracting large amounts of tidal energy. A Severn Barrage, as previously proposed by the Severn Tidal Power Group (STPG), would be the largest renewable energy project for tidal power generation in the world, if built as proposed, and would generate approximately 5% of the UK's electricity needs. However, concerns have been raised over the environmental impacts of such a barrage, including potential increase in flood risk, loss of intertidal habitats etc. In addressing the challenges of maximizing the energy output and minimizing the environmental impacts of such a barrage, this research study has focused on using a Continental Shelf model, based on the modified Environmental Fluid Dynamics Code (EFDC) with a barrage operation module (EFDC_B), to investigate both the far and near field hydrodynamic impacts of a barrage for different operating scenarios. Three scenarios have been considered to simulate the Severn Barrage, operating via two-way generation and using different combinations of turbines and sluices. The first scenario consisted of 216 turbines and 166 sluices installed along the barrage; the second consisted of 382 turbines with no sluices; and the third consisted of 764 turbines and no sluices. The specification of the sluice gates and turbines are the same for all scenarios. The model results indicate that the third scenario has the best mitigating effects for the far-field and near-field flood risks caused by a barrage and produces the most similar results of minimum water depth and maximum velocity distributions to those obtained from simulating the natural conditions of the estuary, i.e. the current conditions. The results also show that the flow patterns around the barrage are closest to those for the existing natural conditions with minimal slight changes in the estuary. Thus, the results clearly indicate that the environmental impacts of a Severn Barrage can be minimized if the barrage is operated for two-way generation and under the third scenario. Although it appears that the energy output for the third scenario is less than that obtained for the other two scenarios, if very low head (VLH) turbines are used, then the third scenario could generate more energy as more turbines could be cited along the barrage structure. Therefore, the study shows that a Severn Barrage, operating in two-way generation and with 764 turbines (ideally VLH turbines), would be the best option to meet the needs of maximizing the energy output, but having a minimal impact on environmental changes in the estuary and far-field.

Abstract The rapid increase in energy demand and the limited resources of fossil fuel as well as the environmentally damaging effects, drive the world to find new options for sustainable electricity generation, which is represented by renewable energies. Concentrating solar power (CSP) is one of the most promising technologies in the field of electricity generation to tackle this issue with a competitive cost in the future. This paper presents an investigation of the potential of implementation of CSP plants in Libya. The socio-economic context, current energy situation of the country and different types of CSP plants are discussed. Moreover, an assessment of site parameters required for CSP plants including solar resources, land use and topography, water resources and grid connections are investigated in detail. In addition, thermo-economic simulation of a 50 MW parabolic trough power plant is performed. The simulation is conducted based on meteorological data measured by the weather station installed at the Centre for Solar Energy Research and Studies (CSERS) in Tajoura city. The performance results are compared with the reference plant Andasol-1 in Spain. Even though the proposed plant is located on the North coast where solar resources are at their minimum compared with other regions of the country, the outcome of the study proves that Libya is not only suitable but it can be economically competitive in the implementation of CSP technology.

For zero‐defect wave soldering of double‐sided and multilayer printed circuit boards, the copper through‐hole‐plating must be impervious to gas generated in the laminate for the period of a few seconds while the solder is molten. The kinetics of the gas evolution during soldering have been related quantitatively to the integrity of the plated copper. This in turn is related to the quality of the electroless copper (evaluated using the backlighting test), the nature and distribution of the catalyst (evaluated using X‐ray photoelectron spectroscopy) and the methods and effectiveness of the hole‐wall preparation (evaluated using scanning electron microscopy). The relevance of laboratory measurements has been confirmed on a wide range of industrial production plating lines.

Abstract Two office layouts with high and low levels of thermal control were compared, respectively traditional cellular and contemporary open plan offices. The traditional Norwegian practice provided every user with control over a window, blinds, door, and the ability to adjust heating and cooling. Occupants were expected to control their thermal environment to find their own comfort, while air conditioning was operating in the background to ensure the indoor air quality. In contrast, in the British open plan office, limited thermal control was provided through openable windows and blinds only for occupants seated around the perimeter of the building. Centrally operated displacement ventilation was the main thermal control system. Users’ perception of thermal environment was recorded through survey questionnaires, empirical building performance through environmental measurements and thermal control through semi-structured interviews. The Norwegian office had 35% higher user satisfaction and 20% higher user comfort compared to the British open plan office. However, the energy consumption in the British practice was within the benchmark and much lower than the Norwegian office. Overall, a balance between thermal comfort and energy efficiency is required, as either extreme poses difficulties for the other.

Abstract Specification by central government of the heating levels which are to be maintained in British school buildings has recently been altered. This paper is concerned with examining the nature of changes that have been made by comparing present requirements with their counterparts during the preceding one hundred years. Attention is focused on the apparently contradictory implications of these changes for those charged with responsibility for maintaining heating levels in school buildings while, at the same time, conserving fuel. It is suggested that the new statutory requirements present those who are responsible with a duty which may, in practical terms, prove difficult or costly to discharge. Although discussion is specifically restricted to British school buildings, issues are raised which are pertinent to attempts to integrate regulation of heating with control of fuel consumption in other types of non-domestic buildings both in Britain and abroad.

Even with state of the art forecasting methods, the short-term generation of wind farms cannot be predicted with a high degree of accuracy. In a market situation, these forecasting errors lead to commercial risk through imbalance costs when advance contracting. This situation is one that needs to be addressed due to the steady increase in the amount of grid connected wind generation, combined with the rise of deregulated, market orientated electricity systems. In the presence of imbalance prices and uncertain generation, a method is required to determine the optimum level of contract energy to be sold on the advance markets. Such a method is presented here using Markov probabilities for a wind farm and demonstrates substantial reductions in the imbalance costs. The effect of market closure delays and forecasting window lengths are also shown.

Abstract In this paper, the possibility of applying a Power System Stabilizer (PSS) via the governor-turbine system of a generating unit is studied for both single-machine and multimachine power systems. The results of analysis and simulation show that the conventional exciter-based PSS can be used in conjunction with the modern high-speed governor to suppress low-frequency oscillations in power systems. This arrangement of stabilizer possesses better robustness to the changes of power system operating conditions. Furthermore, in the environment of a multimachine power system, the control of PSS on the governor of every generator can be locally synthesized to stabilize the whole system, PSS design becomes much easier and simpler.