• Energy Research
• Closed Access close
• Restricted close
• Open Source close
• Embargo close
• GB close
• RU close
• RS close

Abstract An orange and an apple juice each containing 250–385 ppm tin were under suspicion of having caused an outbreak of food poisoning in Kuwait in 1967 but did not cause any toxic signs when fed to pigeons, cats and dogs. One cat out of 11 vomited when fed an orange juice containing 540 ppm tin derived from the container, and with juices containing 1370 ppm tin, 20–30% of the cats vomited but none of the dogs was affected. Fruit juices containing 2000 ppm tin caused vomiting in up to 40% of the cats. Modification of orange juices with a high tin content by addition of nitrate or ethanol or by adjustment of the pH from 3 to 6 did not affect the incidence of vomiting. No toxic signs were produced in rats given fruit juices containing added tin salts up to a level of 995 ppm or in rats and cats given aqueous solutions of tin salts (up to 1200 ppm tin) in citric acid. Solid foods containing tin derived from the containers up to the highest level obtainable (470 ppm) had no toxic effect when fed to dogs and cats. Five human volunteers showed no toxic signs after drinking fruit juices containing 498, 540 or 730 ppm tin derived from the containers, but all five had some gastro-intestinal disturbance after drinking a fruit juice containing 1370 ppm tin. A repeat experiment with the latter juice had no effect in four of the volunteers and only mild symptoms in the fifth. In rats and cats, there was no evidence of tin absorption 24 hr after ingestion of fruit juices containing high levels of tin. No tin was recovered from the urine and in the rats 99% was recovered from the faeces. Only minute amounts of tin could be found in the body, apart from the alimentary tract, of a rat that had been given orange juice with a high tin content ad lib. instead of drinking water for 7 days. It is concluded that toxic signs follow the drinking of tin-containing fruit juices by man and cats only with tin levels of approximately 1400 ppm and above, that there is no evidence from these experiments that toxicity is due to the absorption of tin and that the most likely cause is local irritation of the mucous membrane of the alimentary tract.

For zero‐defect wave soldering of double‐sided and multilayer printed circuit boards, the copper through‐hole‐plating must be impervious to gas generated in the laminate for the period of a few seconds while the solder is molten. The kinetics of the gas evolution during soldering have been related quantitatively to the integrity of the plated copper. This in turn is related to the quality of the electroless copper (evaluated using the backlighting test), the nature and distribution of the catalyst (evaluated using X‐ray photoelectron spectroscopy) and the methods and effectiveness of the hole‐wall preparation (evaluated using scanning electron microscopy). The relevance of laboratory measurements has been confirmed on a wide range of industrial production plating lines.

Abstract Two office layouts with high and low levels of thermal control were compared, respectively traditional cellular and contemporary open plan offices. The traditional Norwegian practice provided every user with control over a window, blinds, door, and the ability to adjust heating and cooling. Occupants were expected to control their thermal environment to find their own comfort, while air conditioning was operating in the background to ensure the indoor air quality. In contrast, in the British open plan office, limited thermal control was provided through openable windows and blinds only for occupants seated around the perimeter of the building. Centrally operated displacement ventilation was the main thermal control system. Users’ perception of thermal environment was recorded through survey questionnaires, empirical building performance through environmental measurements and thermal control through semi-structured interviews. The Norwegian office had 35% higher user satisfaction and 20% higher user comfort compared to the British open plan office. However, the energy consumption in the British practice was within the benchmark and much lower than the Norwegian office. Overall, a balance between thermal comfort and energy efficiency is required, as either extreme poses difficulties for the other.

We have developed algorithms and programs for automated tests of synchronous machines. The programs were made using the LabVIEW development system. They are interrelated and have been combined into one software system. An approximation of its characteristics using regression equations of different orders with mean-square rate control is used in the algorithms to determine static parameters. A combined optimizing algorithm that is based on the least squares method and alternating-variable descent method is used to determine dynamic parameters. A new effective and adaptive method of sliding trigonometric interpolation is used to filter out possible noise in measuring channels of voltage and current sensors, while determining the parameters of sinusoidal signals in the stationary modes and dots of envelope curves in the transient modes. To reduce the time needed to obtain static characteristics, the software has a special virtual instrument with a field current control loop with a PID controller that provides desired field forcing. The SMTest software system has been tested using HIL modeling and laboratory test stations. Analysis of test results shows that, even when the acquired signal has a 30% noise level, the calculation error in the determination of parameters does not exceed 6%. The software, when used in stationary or mobile test stations, allows automating the process of obtaining characteristics and determining the main static and dynamic parameters of midand high-power rotor synchronous machines.

This short report substantiates the advisability of developing a two-stage model for the emergence and development of a boiling crisis. One of the stages is the violation of the stability of the two-phase wall layer, and the other is the appearance and fusion of dry spots on the heating surface. The use of a two-stage (“temporary”) model makes it possible to combine both well-known approaches to crisis analysis—hydrodynamic and thermal—in a single logical system. In the first approach, the characteristics of the boiling crisis are characteristic of high pressures in a boiling liquid, while those in the second are for low pressures.

Abstract Specification by central government of the heating levels which are to be maintained in British school buildings has recently been altered. This paper is concerned with examining the nature of changes that have been made by comparing present requirements with their counterparts during the preceding one hundred years. Attention is focused on the apparently contradictory implications of these changes for those charged with responsibility for maintaining heating levels in school buildings while, at the same time, conserving fuel. It is suggested that the new statutory requirements present those who are responsible with a duty which may, in practical terms, prove difficult or costly to discharge. Although discussion is specifically restricted to British school buildings, issues are raised which are pertinent to attempts to integrate regulation of heating with control of fuel consumption in other types of non-domestic buildings both in Britain and abroad.

Even with state of the art forecasting methods, the short-term generation of wind farms cannot be predicted with a high degree of accuracy. In a market situation, these forecasting errors lead to commercial risk through imbalance costs when advance contracting. This situation is one that needs to be addressed due to the steady increase in the amount of grid connected wind generation, combined with the rise of deregulated, market orientated electricity systems. In the presence of imbalance prices and uncertain generation, a method is required to determine the optimum level of contract energy to be sold on the advance markets. Such a method is presented here using Markov probabilities for a wind farm and demonstrates substantial reductions in the imbalance costs. The effect of market closure delays and forecasting window lengths are also shown.

In this paper a novel generalised modelling framework for multi-energy systems containing storage elements is combined with a multi-objective model predictive control. The control objective is to both minimise the economic cost of importing energy into the system as well as providing the service of smoothing the profile of the electrical energy imported thus levelling the load and reducing peak demand. The capabilities of the approach are demonstrated by its application to a representative case study based on two buildings at the University of Manchester. Results show that model predictive control is capable of simultaneously addressing minimisation of economic cost as well as smoothing the electrical energy import.