• Energy Research
• engineering and technology close
• 13. Climate action close
• IN close
• OM close

Drying experiments have been performed with potato cylinders and slices using a laboratory scale designed natural convection mixed-mode solar dryer. The drying data were fitted to eight different mathematical models to predict the drying kinetics, and the validity of these models were evaluated statistically through coefficient of determination (R(2)), root mean square error (RMSE) and reduced chi-square (χ (2)). The present investigation showed that amongst all the mathematical models studied, the Modified Page model was in good agreement with the experimental drying data for both potato cylinders and slices. A mathematical framework has been proposed to estimate the performance of the food dryer in terms of net CO2 emissions mitigation potential along with unit cost of CO2 mitigation arising because of replacement of different fossil fuels by renewable solar energy. For each fossil fuel replaced, the gross annual amount of CO2 as well as net amount of annual CO2 emissions mitigation potential considering CO2 emissions embodied in the manufacture of mixed-mode solar dryer has been estimated. The CO2 mitigation potential and amount of fossil fuels saved while drying potato samples were found to be the maximum for coal followed by light diesel oil and natural gas. It was inferred from the present study that by the year 2020, 23 % of CO2 emissions can be mitigated by the use of mixed-mode solar dryer for drying of agricultural products.

Abstract In this work addition of ethanol to high viscosity jatropha methyl ester (JME) through port injection is investigated in order to determine its effect fuel viscosity reduction on diesel engine performance. In addition to viscosity alteration, the impact of ethanol addition on combustion characteristics such as combustion duration, ignition delay and emissions levels from diesel engines fuelled with blends of ethanol, diesel and JME is studied in particular. It is found that blending of oxygenated fuels with diesel modifies the chemical structure and physical properties which again alter the engine operating conditions, combustion parameters and emissions levels. However, the injection of only 5% ethanol through port injection allows for a total of 25% blending of biofuels into diesel yet keeping the fuel characteristics close to that of conventional diesel. However, both experimental and numerical results show that ethanol addition in JME blended diesel results in a slight increase in fuel consumption and thermal efficiency for the same power outputs as that of conventional diesel fuel. Also, the combustion characteristics with ethanol addition include improved maximum in-cylinder peak pressure, cumulative heat release (CHR) rate of heat release (ROHR), in-cylinder peak temperature and combustion duration. Regarding emission characteristics the experimental results show significant reduction in smoke, carbon monoxide (CO) and total hydrocarbon (THC) emissions with extended oxygen mass percentage in the fuel at higher engine loads. However, oxides of nitrogen (NOx) emissions are found to increase at high loads although the common tradeoff between smoke and NOx is found to be more prominent for the oxygenated fuels.

Abstract The main hindrances to the large-scale development of renewable-energy projects are the lack of bankability and the inability to align investments and investors with suitable financial instruments or robust policy measures. To illustrate a bankable project, this paper presents a research-based case study on the installation of solar photovoltaic panels on the rooftops of 195 trains of the Indian Railways. Detailed information on the annual running hours, exposure to sunlight, efficiency of solar photovoltaic generation and electrical power demands of each rail coach is considered to conduct a quantitative measure of the tentative amount of fossil fuel savings. The purpose is to provide insight into the types of renewable-energy projects that can be highly attractive to financial institutions and promoters due to their lucrative internal return on investment. As seen in this case study, there are annual savings in diesel of 12 323 088 litres and a CO2 reduction of 32 755 tonnes, with return on investment of 1.3 years. Furthermore, this study conducts a comprehensive analysis of the limitations of existing renewable-energy project financing mechanisms in India. Subsequently, three policy measures are recommended to develop a robust financial mechanism that can effectively meet the needs of investors and investors. These measures include increasing equity injection through a buy-and-hold strategy, providing direct tax benefits to promoters and financing through real-estate investment trusts. The findings are highly relevant to address the challenges associated with bridging the financial gap between access to finance and capital investment in the renewable-energy sector, especially for Asian countries.

Abstract This paper aims to present a feasibility study of the innovative plant for methanol synthesis from carbon dioxide-sequestered by fossil fuel power plant and hydrogen, which is produced by water electrolyzer employing the over-production on the electrical grid. The thermo-economic analysis is performed in the framework of the MefCO2 H2020 EU project and it is referred to the German economic scenario, properly taking into account the real market costs and cost functions for different components of the plant. Three different plant capacities for methanol production (4000 10,000 and 50,000 ton/year) have been investigated, assuming an average cost for electrical energy to feed electrolysers and analyzing the influence of the most significant parameters (oxygen selling option, methanol selling price and electrolysers’ capital cost) on the profitability of the plant. The analysis has been performed in W-ECoMP, software for the thermo-economic analysis and plant optimization developed by the University of Genoa.

Abstract The present work attempts to devise an efficient method utilizing an on-grid photovoltaic-thermal heat pump water heater (PV-THPWH) integrated with a real-time variable frequency controller to achieve the goal of energy-efficient buildings. The prime focus is to reduce the grid's dependence on the compressor's energy-intensive operation by employing a feedback-controlled variable frequency drive (VFD). Additionally, the possibilities involved with addressing the electrical and thermal energy requirements of an energy-efficient building was investigated utilizing the proposed system. R-32 refrigerant in the photovoltaic-thermal (PV-T) evaporator coils of the heat pump assembly help to cool the photovoltaic (PV) panel while delivering the absorbed heat in the condenser to heat water contained inside the storage tank. Outdoor experiments and theoretical investigations of the combined system were carried out to appraise the dynamic behavior under varying solar irradiation and ambient temperature conditions. The observations conveyed that the PV-THPWH system succeeded in reducing the PV panel operating temperature by 25%, which resulted in a 20% increment in PV power output. Also, the performance indicators, such as the instantaneous energy efficiency and instantaneous PV efficiency, were found to increase by 15% and 34%, respectively, resulting in an average coefficient of performance of 6.4. For a clear sky day, the recorded total PV energy output was 4.67 units, while the VFD compressor consumption was 3.42 units, and the surplus 1.25 units were sent to the grid. Furthermore, the economic analysis reported a payback period of 2.3 years for the developed PV-THPWH system.

Considerable interest is being shown in using biochar production from waste biomass with a variety of disciplines to address the most pressing environmental challenges. Biochar produced by the thermal decomposition of biomass under oxygen-limited conditions is gaining popularity as a low-cost amendment for agro-ecosystems. The efficiency of biochar formation is affected by temperature, heating rate, feedstock type, particle size and reactor conditions. Properties such as pH, surface area and ash content of produced biochar increases with increasing temperatures. Biochar produced at lower heating rates may have high porosity and be beneficial for morphological changes in the soil. Biochar can help to enhance soil health and fertility as well as improve agricultural yield. As a result, biochar can assist in increasing food security by promoting sustainable agricultural systems and preserving an eco-friendly environment. Biochar is also widely being used as a sorbent for organic and inorganic pollutants, owing to its large surface area, allowing it to be immobilized from soil with ease. The functional groups and charges present on the surface of biochar play an important role in pollutants removal. This review focuses on the mechanisms of biochar production using different waste materials as a feed stock, factors that influence biochar quality as well as application of biochar in agricultural soil and their reclamation as well. This article also discusses knowledge gaps and future perspectives in the field of biochar-based toxic-pollution remediation.

The growing population and increasing urbanization have led to a surge in domestic wastewater generation, posing significant challenges for effective and sustainable treatment. The present study demonstrates a novel and sustainable approach for the onsite treatment of domestic wastewater using an integrated settler-based biofilm reactor (ISBR) with efficient biogas generation. The ISBR provides an optimized environment for the growth of biofilm, facilitating the removal of organic pollutants and pathogens. Moreover, the ISBR enables the recovery of a valuable resource in the form of biogas, thus enhancing the overall utility of the treatment process. The performance of the ISBR was comprehensively evaluated at laboratory scale through treating the actual domestic wastewater generated from the hostel of Manipal University Jaipur. The ISBR system was operated under an ambient environment at a hydraulic retention time (HRT) of 24 h. The results demonstrated remarkable efficiency in terms of chemical oxygen demand (COD), total suspended solids (TSS), and coliforms removal, with average removal efficiency being more than 90%. According to the COD mass balance analysis, 48.2% of the influent COD was recovered as bioenergy. The chromatogram revealed a high percentage of methane gas in the collected biogas sample. The field emission scanning electron microscope (FESEM) analysis of the accumulated sludge in the ISBR system depicted the morphology of methanogenic bacteria. Both the experimental and theoretical results confirmed the feasibility and sustainability of the ISBR system at the onsite level.

AbstractRecently, modern power systems depend heavily on MicroGrids (MGs), which can accommodate Distributed Energy Resources (DERs) economically and with high flexibility. MGs integrated with DERs can assist in enhancing energy security, significant cost savings, and reduction in emission of greenhouse gases. In this paper, the assessment of operating performance of proposed MG system with DERs is employed to investigate the multi‐objective problems of cost optimization and economic scheduling. A grid‐connected Micro‐grid (MG) combined with solar photovoltaic (PV), wind turbine (WT), fuel cell (FC), and Battery Energy Storage System (BESS) is implemented to model the problem. This proposed model is considered as a test system for cost optimization and battery charging/discharging optimization. The developed framework is presented as multi‐objective function with constraints that can be tackled using an effective optimization technique. The above stochastic multi‐objective problem is optimized using various commonly used Physics based Meta‐heuristic techniques such as Simulated Annealing (SA), Harmony Search (HS), Slime Mold Algorithm (SMA), Gravitational Search Algorithm (GSA), Black Hole Optimization (BHO), Sine Cosine Algorithm (SCA), Multiverse optimization (MVO) and Lightning Search Algorithm (LSA). The assessment of the aforementioned physics‐based optimization techniques used on the proposed MG test system is compared using the results. According to the analysis, Black Hole Optimization (BHO) and Lightning Search Algorithm (LSA) both provide greater cost savings overall and for battery charging, respectively. The suggested optimization methods will take the BESS charging/discharging pattern and total cost savings into account.

Large-size woody biomass is a valuable renewable resource to replace fossil fuels in biorefinery processes. The preprocessing of wood chips and briquettes is challenging to manage, especially in an industrial setting, as it generates a significant amount of dust and noise and occasionally causes unexpected accidents. As a result, a substantial amount of resources, energy, labor, and space are needed. The thermochemical conversion behavior of large-size woody biomass was studied to reduce energy consumption for chipping. Large-size wood was 1.5 m in length, 0.1 m in breadth, and stacked 90 cm in height. This strategy has many benefits, including increased effectiveness and reduced CO2 emissions. The target of this paper presents the thermochemical process, and large-size wood was chosen because it provides high-quality product gas while reducing the preprocessing fuel cost. This review examines the benefits of thermochemical conversion technologies for assessing the likelihood of carbon neutrality.