• Energy Research
• other engineering and technologies close
• 12. Responsible consumption close
• 11. Sustainability close
• IN close
• RU close
• SA close

Torrefaction is considered as a method for producing biofuels with improved characteristics compared to those of the “raw” biomass (higher calorific value, moisture resistance, better grindability). The torrefaction process is an endothermic process that is usually carried out in a gaseous atmosphere in the absence of oxygen. To reduce the required heat input, it is proposed to employ the oxidative torrefaction and conduct the process in a fluidized bed agitated with flue gases containing less than 6% oxygen. Preliminary studies of the oxidative torrefaction of sunflower husks, including thermogravimetric analysis of the treated material, have shown that the heat treatment time for the biomass should be at least 5 min. A fluidized bed is a reactor with ideal mixing of the treated material where uniform treatment of raw material particles cannot generally be attained. To overcome this disadvantage of the fluidization technique and achieve the required residence time for biomass in a fluidized bed during a continuous torrefaction process, it was proposed to equip a torrefaction reactor with a series of vertical baffles spaced at 50 mm. These baffles induce a loop-like flow of the processed biomass from the inlet to the outlet of the reactor. To investigate the residence time for husk particles in the reactor, a tracer, which was colored to husk particles' color with a water-soluble dye which did not change the weight and size of the particles, was injected into the bed of uncolored particles. Tracer samples were taken every 30 s at the outlet of the reactor and were analyzed using a special procedure to determine the fraction of colored particles in each sample. This enabled us to gauge the time during which the colored particles injected into the fluidized bed reached the point of their discharge from the bed. Studies performed in a “cold” model of the reactor showed that a series of vertical baffles in the bed can provide the required residence time for biomass in a reactor including commercial reactors. Plates can provide the necessary biomass residence time in the reactor.

Second-generation bioethanol can be produced from various lignocellulosic biomasses such as wood, agricultural or forest residues. Lignocellulosic biomass is inexpensive, renewable and abundant source for bioethanol production. The conversion of lignocellulosic biomass to bioethanol could be a promising technology though the process has several challenges and limitations such as biomass transport and handling, and efficient pretreatment methods for total delignification of lignocellulosics. Proper pretreatment methods can increase concentrations of fermentable sugars after enzymatic saccharification, thereby improving the efficiency of the whole process. Conversion of glucose as well as xylose to bioethanol needs some new fermentation technologies to make the whole process inexpensive. The main goal of pretreatment is to increase the digestibility of maximum available sugars. Each pretreatment process has a specific effect on the cellulose, hemicellulose and lignin fraction; thus, different pretreatment methods and conditions should be chosen according to the process configuration selected for the subsequent hydrolysis and fermentation steps. The cost of ethanol production from lignocellulosic biomass in current technologies is relatively high. Additionally, low yield still remains as one of the main challenges. This paper reviews the various technologies for maximum conversion of cellulose and hemicelluloses fraction to ethanol, and it point outs several key properties that should be targeted for low cost and maximum yield.

The distribution feeders often gets overload under peak power demands. This situation is generally countered by load shading, which leads to financial losses to utilities and individual users. This paper presents the new methodology to support the real and reactive power demand through energy storage (ES) to avoid the load shading situation. The compensation of real / reactive power not only provides the voltage profile improvement but also ensures the sustain power to the consumers. A control scheme incorporated also maintains the unity power factor on source side. This relieves the existing distribution network from the extra reactive loading hence the line is having extra capacity for real power transfer to its maximum thermal limit. This additional capacity availability adds more customer base to justify the energy storage investment. The operational features are presented through a simulation of a realistic urban feeder data. The financial analysis is also presented to justify the energy storages with the distribution networks.

The current status and challenges associated with the production and utilization of cellulosic ethanol in Korea are reviewed in this paper. Cellulosic ethanol has emerged as a promising option for mitigating Korea's CO(2) emissions and enhancing its energy security. Korea's limited biomass resources is the most critical barrier to achieving its implementation targets for cellulosic ethanol. Efforts to identify new suitable biomass resources for cellulosic ethanol production are ongoing and intensive. Aquatic biomasses including macroalgae and plantation wastes collected in the Southeast Asia region have been found to have great potential as feedstocks for the production of cellulosic ethanol. R&D explorations into the development of technologies that can convert biomass materials to ethanol more efficiently also are underway. It is expected that cellulosic ethanol will be in supply from 2020 and that, by 2030, its use will have effectively reduced Korea's total gasoline consumption by 10%.

As smart cities become a global topic, interest in smart mobility, the core of smart cities, is also growing. The technology that comes closest to general users is “autonomous driving”. In particular, the successful market entry and establishment of some private companies proved that “autonomous driving” is not technology of the future but imminent reality. However, safety in autonomous vehicles that rely on sensors instead of the driver’s five senses has been the focus of attention from the beginning and continues to be so. In this study, we attempted to counter this interest. Based on the actual data of thirty traffic accidents, assuming the AEBS (Autonomous Emergency Braking System) was installed to assist the driver in safe driving, it was reinterpreted through simulation to see what changes occurred in the accident. In the computer program, PC-Crash, the results were first analyzed through simulation using Euro NCAP (New Car Assessment Program)’s AEBS test standards. Subsequently, the other variables in the AEBS were controlled and the accident was reinterpreted by changing only the angle of the radar detection sensor. As a result, it was confirmed that a total of 27 accidents out of thirty accidents could have been prevented with the AEBS. In addition, it proved that the crash avoidance rate of vehicles gradually increased as the radar angle increased.

Introduction. The article presents an analysis of researches on the operation of public transport vehicles with an electric drive. Electric buses have been tested in megacities, and despite the advantages, problems were identi- fied both in the selection of the charging type, technological features and with the availability and operation of the charging infrastructure. The operation process is associated with a number of technical restrictions, which in prac- tice make it difficult to select routes for the electric bus operation. The aim of the study is to develop an algorithm for selecting a rational regular urban route for the electric bus operation and to test it on the example of the route network of Tyumen.Materials and methods. A structural diagram of the factors influencing the selection of the route for the electric bus operation has been formed. As a result of processing expert assessments, the most significant factors were identified. The diagram of the interconnections of these factors is identified and limitations for the algorithm are for- mulated based on the theory of systems analysis. The algorithm for selecting the rational regular urban route for the electric bus operation has been developed. It enables creating the simulation model for selecting a rational regular urban route for the operation of an electric bus.Results. The diagram of factors influencing the selection of a rational regular urban route for the operation of an electric bus, taking into account their mutual relations, has been formed. The algorithm and simulation model for se- lecting a rational regular urban route for the operation of an electric bus has been developed. Several urban routes in Tyumen were assessed for the rationality of the introduction of electric buses.Discussion and conclusions. Evaluation of five regular urban routes in Tyumen using the developed algorithm and the simulation model revealed three rational routes, and also showed the inefficiency of the other two. It due to the discrepancy between the duration of the charging session and breaks in operation, as well as the insufficient charge level of the traction battery to ensure the required autonomous movement of the vehicle. In the course of the continuation of these studies, the developed algorithm will be supplemented with the stage of economic assess- ment of routes for the operation of electric buses.

India's steadily expanding populace has made it important to create innovative methods of transportation with electric vehicles (EV's) being the most favoured alternative. The major impediment is the negative impact caused by the improper setup of charging stations on the utility distribution system. This paper takes up the issue of optimal planning (siting and sizing) of charging station (CS) infrastructure in the city of Allahabad, India. It has been labelled as a future smart city under a pilot transportation project started by Government of India. A hybrid algorithm comprising of Genetic Algorithm and improved version of conventional Particle Swarm Optimization (GAIPSO) is employed in this study. The aim is to find optimal location of proposed charging stations in the Allahabad distribution system. PSO further re-optimizes the received sub-optimal solution (site and size of station) which leads to an overall improvement in its functionality and solution. Simulation studies on a real time system of Allahabad city clearly exhibits the superior performance of the aforementioned technique with respect to GA and PSO in terms of improvement in voltage profile and quality of solution obtained for the objective function.

The research deals with the issue of slums, urban sprawl on agriculture land and its impact on the city of Baghdad. This topic needs close attention because it has become a problem facing the city of Baghdad through recruiting agricultural lands and converting them to residential homes in addition to the transgression on the state lands and building abuses. This research deals with the causes of slums, irregular urban sprawl and risks of excesses on land uses of land in Baghdad. In this research, we try to know the extent to which these problems have affected the city of Baghdad. The research methodology based on the descriptive methodology to clarify the factors affecting urban sprawl at the expense of agricultural land, using studies in government and service institutions and images from satellites to clarify the size of urban sprawl over periods after the 2003 war. Finally, a conclusion and future solutions were set to solve these problems.