• Energy Research
• 7. Clean energy close
• IN close
• SA close
• BE close

Abstract Designing a high-performance hydrofoil is a fundamental challenge for the current turbine blade designers. In this paper, the performance of S1210 hydrofoil, commonly used in the tidal current turbine blades, in presence of (i) Vortex Generators (VGs), and (ii) modified trailing edge is numerically studied. The results show that attaching counter-rotating VGs near the trailing edge of the foil can increase the lift coefficient by 17% and delay the stall angle from 10° to 12°. Constructing a rounded and thicker trailing edge can help to improve the hydrodynamic performance by increasing the lift coefficient by 13.5%. The combination of VGs (located near the trailing edge) and rounded trailing edge can increase the glide ratio significantly. These observations have been explained by plotting the pressure coefficients and velocity profiles at different locations on the foil surface. The findings will be useful to manufacture a stronger blade profile and extract more power from the current turbines that operate at wide current speed variation.

Longitudinal flow through central subchannel structures in an array of fuel rods in a nuclear reactor plays an important role in removing the heat generated inside the fuel rods. In this paper, an entropy generation analysis has been carried out for assessment of the performance of an infinite triangular as well as a square subchannel for single-phase forced turbulent flow. The performance is evaluated with the objective function being the overall entropy generation in a central subchannel. Various constraints such as dimensionless flow area subtended by the array of rods, pitch to diameter ratio for the configuration of rod bundles and volumetric heat generation to power density ratio of the subchannel imposed by power restrictions have been considered. The parameters include the dimensionless wall heat flux, duty parameter, length to diameter ratio for fuel rods, Reynolds number etc. It has been observed that for a pitch to diameter ratio constraint the square subchannel generates lesser amount of entropy and thus more acceptable compared to triangular structure. For the same constraint the optimum Reynolds number shifts towards higher value compared to triangular one. For dimensionless flow area constraint, on the other hand, the analysis reveals completely reverse phenomenon.

Abstract Thermal energy storage systems based on Phase change materials (PCM) are an attractive option to bridge the temporal and spatial gap between the energy demand and supply. But, these systems possess poor thermal conductivity causing reduced rate of heat transfer. The objective of the present study is to numerically analyze the melting process in an optimized finned latent heat storage system dispersed with varying volume fraction of Graphene nano plates (GNP). The individual effect of incorporating fins, GNP and a combination of both at different volume fraction has been studied. Effective thermal conductivity of nano-composite PCM has been theoretically evaluated including the effect of aspect ratio, interfacial thermal resistance, anisotropy, non-linear effects as well as concentration for the dispersed GNP. In this work, Dynamic differential scanning calorimetry tests are performed to evaluate the phase change temperature, latent heat and specific heat of the sugar alcohol (d- mannitol). Transient variation of liquid fraction, average temperature and radial/longitudinal temperature differentials are presented which would be useful for designing medium temperature (160–200 °C) storage systems for various applications. Fin height is varied to obtain an optimum fin size such that natural convection currents are not impeded. Various heat transfer models (including natural convection) are analysed using the actual plant data of a double effect solar absorption system at different arrangements of fins and GNP. Effect of Reynolds number and inlet temperature of HTF on the system performance have also been studied. A reduction of 68% in total melting time is observed in finned LHSS with 5% GNP as compared to a conventional system.

Abstract Hybrid nanofluids are a novel class of colloidal fluids which have drawn significant attention due to potential tailoring of their thermo-physical properties for heat transfer enhancement by a combination of more than one nano-additive to meet specific requirements of an application. In the present work, ceramic copper oxide/carbon (SiO2-CuO/C) nanoparticles in 80:20 (wt%) composition were prepared by ultrasonic-assisted wet mixing technique. The hybrid nanofluid was formulated by dispersing the nanoparticles into a base fluid mixture of 60:40 (% by mass) glycerol and ethylene glycol (G/EG) using the two-steps method. The influence of nanoparticles on the augmentation of specific heat, thermal conductivity and viscosity was examined in the volume concentration range of 0.5–2.0% in the temperature range of 303.15–353.15 K. The results demonstrate that the synthesized SiO2-CuO/C hybrid nanoparticles enhanced the thermo-physical properties of the base fluid mixture which is higher than using SiO2 alone. In the case of SiO2–G/EG nanofluid, the specific heat capacity decremented by a maximum value of 5.7% whereas the thermal conductivity and viscosity incremented by 6.9% and 1.33-times as compared with G/EG at maximum volume concentration of 2.0% at a temperature of 353.15 K. Comparatively, a reinforcement of 80% SiO2 with 20% CuO/C in G/EG mixture led to thermal conductivity and viscosity enhancement by 26.9% and 1.15-times, respectively with a significant reduction of specific heat by 21.1%. New empirical correlations were proposed based on the experimental data for evaluation of thermophysical properties.

The heat generation from recent advanced computer chips is increasing rapidly. This creates a challenge in cooling the chips while maintaining their temperatures below the threshold values. Another challenge is that the heat generation in the chip is not uniform where some chip components generate more heat than other components. This would create a large temperature gradient across the chip, resulting in inducing thermal stresses inside the chip that may lead to a high probability to damage the chip. The locations in the chip with heat rates that correspond to high heat fluxes are known as hotspots. This research study focuses on using thermoelectric modules (TEMs) for cooling chip hotspots of different heat fluxes. When a TEM is used for cooling a chip hotspot, it is called a thermoelectric cooler (TEC), which requires electrical power. Additionally, when a TEM is used for converting a chip’s wasted heat to electrical power, it is called a thermoelectric generator (TEG). In this study, the TEMs are used for cooling the hotspots of computer chips, and a TEC is attached to the hotspot to reduce its temperature to an acceptable value. On the other hand, the other cold surfaces of the chip are attached to TEGs for harvesting electrical power from the chip’s wasted heat. Thereafter, this harvested electrical power (HEP) is then used to run the TEC attached to the hotspot. Since no external electrical power is needed for cooling the hotspot to an acceptable temperature, this technique is called a sustainable self-cooling framework (SSCF). In this paper, the operation principles of the SSCF to cool the hotspot, subjected to different operating conditions, are discussed. As well, considerations are given to investigate the effect of the TEM geometrical parameters, such as the P-/N-leg height and spacing between the legs in both operations of the TEC mode and TEG mode on the SSCF performance.

Abstract It is well known that Espinosa-parades et al. (Espinosa-Paredes et al., 2011) proposed a fractional neutron point kinetic (FNPK) model with multi-group of delayed neutrons to describe dynamic behavior in a nuclear reactor. In (Aboanber and Nahla, 2016b), Aboanber and Nahla presented an extension of Espinosa-parades et al. FNPK model. This new model is called as the corrected fractional neutron point kinetic (CFNPK) model. The present study is concerned with the numerical solution of the CFNPK model (Aboanber and Nahla, 2016b) with six groups of delayed neutron precursors. The fractional derivative is described in the sense of Grunwald-Letnikov. An implicit finite difference method (FDM) is constructed for the solution of CFNPK model. The stability analysis of the method is carried out. We analyze the results of neutron density for different values of anomalous diffusion order, reactivity function, relaxation time and time step size. In addition, we compare the results corresponding to CFNPK model (Aboanber and Nahla, 2016b) with the results corresponding to the FNPK model proposed by Espinosa-parades et al. (Espinosa-Paredes et al., 2011). It is shown that as anomalous diffusion order decreases or simulation time increases the difference between the values of neutron density increases. We have investigated the effects of each term of the CFNPK.

Abstract Emissions and efficiency of a pellet boiler (40 kW) at nominal load were compared with emissions and efficiency at reduced load, while fired with six biomass pellets. The pellets include reed canary grass ( Phalaris arundinacea ), pectin waste from citrus shells ( Citrus reticulata ), sunflower husk ( Helianthus annuus ), peat, wheat straw ( Triticum aestivum ) and wood pellets. The measurements of emissions comprised of carbon monoxide (CO), nitrogen oxides (NO x ), sulphur oxides (SO x ) and flue dust mass concentrations (using DIN plus and isokinetic sampling techniques). Emissions varied as a function of operational loads, for each type of pellets. The CO emissions were insignificant with reed canary grass (RCG), citrus pectin waste (CPW) and straw pellets at nominal load, however, at reduced load same pellets emitted 1.9, 4.0 and 7.4 times higher CO than wood pellets, respectively. Peat pellets emitted maximum CO at nominal load (4221.1 mgNm −3 , 12.6 times higher than wood pellets) however; at reduced load CO emission was insignificant. The highest NO x emissions were reported with CPW, which were 3.4 and 4.6 times higher than wood pellets at nominal load and reduced load, respectively. Dust emissions were highest with sunflower husk and lowest with RCG pellets, at both operational modes. The best performance was reported with wood pellets, followed by RCG and pectin pellets, however, wood pellets combustion emitted 1.7 and 2.0 times higher dust DIN plus than RCG at nominal and reduced loads, respectively. Not only fuel specific combustion optimization but also operational load specific optimization is essential for efficient use of agro-pellets in this type of boilers.

The present study utilizes (a) recycled low density polyethylene oil extracted through catalytic pyrolysis and (b) 1-decanol and di-n-butyl ether, as a blend component with diesel to power a single...

In the current situation with the unprecedented deployment of clean technologies for electricity generation, it is natural to expect that storage will play an important role in electricity networks. This paper provides a qualitative methodology to select the appropriate technology or mix of technologies for different applications. The multiple comparisons according to different characteristics distinguish this paper from others about energy storage systems. Firstly, the different technologies available for energy storage, as discussed in the literature, are described and compared. The characteristics of the technologies are explained, including their current availability. In order to gain a better perspective, availability is cross-compared with maturity level. Moreover, information such as ratings, energy density, durability and costs is provided in table and graphic format for a straightforward comparison. Additionally, the different electric grid applications of energy storage technologies are described and categorised. For each of the categories, we describe the available technologies, both mature and potential. Finally, methods for connecting storage technologies are discussed.