• Energy Research
• Closed Access close
• engineering and technology close
• AU close
• IT close

According to the renewable energy directive 2009/28/EC, the European Union Member States should increase by 2020 the use of renewable energy to 20% of gross final energy consumption and to reach a mandatory share of 10% renewable energy in the transport sector. This study aims to quantify the impact of 2020 bioenergy targets on the land use in the EU, based on the projections of the National Renewable Action Plans in four scenarios: Scenario 1. Bioenergy targets according to NREAPs; Scenario 2. Bioenergy targets according to NREAPs, no second generation biofuels; Scenario 3. Bioenergy targets according to NREAPs, reduced import of biofuels and bioliquids; Scenario 4. Bioenergy targets according to NREAPs, high imports of biofuels and bioliquids. This study also considers the credit for co-products generated from biofuel production. The analysis reveals that the land used in the EU for bioenergy would range between 13.5 Mha and 25.2 Mha in 2020. This represent between 12.2% and 22.5% of the total arable land used and 7.3% and 13.5% of the Utilised Agricultural Area (UAA). In the NREAPS scenario, about 17.4 Mha would be used for bioenergy production, representing 15.7% of arable land and 9.4% of UAA. The increased demand from biofuels would lead to an increased generation of co-products, replacing conventional fodder for animal feed. Considering the co-products, the land used for bioenergy would range between 8.8 Mha and 15.0 Mha in 2020 in the various scenarios. This represent between 7.9% and 13.3% of the total arable land used in the EU and 4.7% and 8.0% of the UAA. In the NREAPS scenario, when co-products are considered, about 10.3 Mha would be used for biofuels, bioliquids and bioenergy production, representing 9.3% of arable land and 5.6% of agricultural land. This study further provides detailed data on the impact on land use in each Member State.

According to the renewable energy directive 2009/28/EC, the European Union Member States should increase by 2020 the use of renewable energy to 20% of gross final energy consumption and to reach a mandatory share of 10% renewable energy in the transport sector. This study aims to quantify the impact of 2020 bioenergy targets on the land use in the EU, based on the projections of the National Renewable Action Plans in four scenarios: Scenario 1. Bioenergy targets according to NREAPs; Scenario 2. Bioenergy targets according to NREAPs, no second generation biofuels; Scenario 3. Bioenergy targets according to NREAPs, reduced import of biofuels and bioliquids; Scenario 4. Bioenergy targets according to NREAPs, high imports of biofuels and bioliquids. This study also considers the credit for co-products generated from biofuel production. The analysis reveals that the land used in the EU for bioenergy would range between 13.5 Mha and 25.2 Mha in 2020. This represent between 12.2% and 22.5% of the total arable land used and 7.3% and 13.5% of the Utilised Agricultural Area (UAA). In the NREAPS scenario, about 17.4 Mha would be used for bioenergy production, representing 15.7% of arable land and 9.4% of UAA. The increased demand from biofuels would lead to an increased generation of co-products, replacing conventional fodder for animal feed. Considering the co-products, the land used for bioenergy would range between 8.8 Mha and 15.0 Mha in 2020 in the various scenarios. This represent between 7.9% and 13.3% of the total arable land used in the EU and 4.7% and 8.0% of the UAA. In the NREAPS scenario, when co-products are considered, about 10.3 Mha would be used for biofuels, bioliquids and bioenergy production, representing 9.3% of arable land and 5.6% of agricultural land. This study further provides detailed data on the impact on land use in each Member State.

Microalgae have tremendous potential for producing liquid renewable fuel. Many methods for converting microalgae to biofuel have been proposed; however, an economical and energetically feasible route for algal fuel production is yet to be found. This paper presents a review on the comparison of the most promising conversion pathways of microalgae to liquid fuel: hydrothermal liquefaction (HTL), wet extraction and non-destructive extraction. The comparison is based on important assessment parameters of product quality and yield, nutrient recovery, GHG emissions, energy and the cost associated with the production of fuel from microalgae, in order to better understand the pros and cons of each method. It was found that the HTL pathway produces more oil than the wet extraction pathway; however, higher concentrations of unwanted components are present in the HTL oil produced. Less nutrients (N and P) can be recovered in HTL compared to wet extraction. HTL consumes more fossil energy and generates higher GHG emissions than wet extraction, while the production cost of fuel from HTL pathway is lower than wet extraction pathway. There is considerable uncertainty in the comparison of the energy consumption and economics of the HTL pathway and the wet extraction pathway due to different scenarios analysed in the assessment studies. To be able to appropriately compare methodologies, the conversion methods should be analysed from growth to upgradation of oil utilising sufficiently similar assumptions and scenarios. Based on the data in available literature, wet oil extraction is the more appropriate system for biofuel production than HTL. However, the potential of alternative extraction/conversion technologies, such as, non-destructive extraction, need to be further assessed.

Microalgae have tremendous potential for producing liquid renewable fuel. Many methods for converting microalgae to biofuel have been proposed; however, an economical and energetically feasible route for algal fuel production is yet to be found. This paper presents a review on the comparison of the most promising conversion pathways of microalgae to liquid fuel: hydrothermal liquefaction (HTL), wet extraction and non-destructive extraction. The comparison is based on important assessment parameters of product quality and yield, nutrient recovery, GHG emissions, energy and the cost associated with the production of fuel from microalgae, in order to better understand the pros and cons of each method. It was found that the HTL pathway produces more oil than the wet extraction pathway; however, higher concentrations of unwanted components are present in the HTL oil produced. Less nutrients (N and P) can be recovered in HTL compared to wet extraction. HTL consumes more fossil energy and generates higher GHG emissions than wet extraction, while the production cost of fuel from HTL pathway is lower than wet extraction pathway. There is considerable uncertainty in the comparison of the energy consumption and economics of the HTL pathway and the wet extraction pathway due to different scenarios analysed in the assessment studies. To be able to appropriately compare methodologies, the conversion methods should be analysed from growth to upgradation of oil utilising sufficiently similar assumptions and scenarios. Based on the data in available literature, wet oil extraction is the more appropriate system for biofuel production than HTL. However, the potential of alternative extraction/conversion technologies, such as, non-destructive extraction, need to be further assessed.

AbstractAn arc‐furnace model consisting of non‐linear, time‐varying resistance, realized by the Alternative Transients Program (ATP), is presented in this paper. It is shown that the model is appropriate for flicker investigation in electrical networks supplying arc furnaces, constituting a valid alternative to the linear arc modelling realized by amplitude modulation of voltage generators. Block diagram of the procedure for ATP modelling of the nonlinear, time‐varying arc resistance, dynamic voltage‐current characteristic of the furnace electric arc, voltage and current arc waveforms and characteristic curves of an arc furnace, obtained by ATP simulation, are presented, referring to circuit parameters taken from an actual plant and to a sinusoidal law for arc‐length time variation. Aflickermeter ATP simulation is realized to derive equivalent voltage‐variation values in agreement with the actual flicker measurements.

AbstractAn arc‐furnace model consisting of non‐linear, time‐varying resistance, realized by the Alternative Transients Program (ATP), is presented in this paper. It is shown that the model is appropriate for flicker investigation in electrical networks supplying arc furnaces, constituting a valid alternative to the linear arc modelling realized by amplitude modulation of voltage generators. Block diagram of the procedure for ATP modelling of the nonlinear, time‐varying arc resistance, dynamic voltage‐current characteristic of the furnace electric arc, voltage and current arc waveforms and characteristic curves of an arc furnace, obtained by ATP simulation, are presented, referring to circuit parameters taken from an actual plant and to a sinusoidal law for arc‐length time variation. Aflickermeter ATP simulation is realized to derive equivalent voltage‐variation values in agreement with the actual flicker measurements.

Abstract The central role of occupants for achieving energy savings in residential buildings is increasingly recognised. Simulation programmes able to take into account occupant behaviour are considered to be powerful tools for bridging the gap between the predicted and the actual energy consumption for new buildings. Nevertheless, the majority of residential buildings that will constitute the housing stock in 2050 have already been built today, therefore occupant behaviour and building simulation tools need to be fully exploited for supporting the renovation of existing housing stock. The aim of this paper is to explore the role of occupant behaviour modelling in supporting decision-makers dealing with the design of renovation strategies for residential buildings. An Italian multi-family public housing building is assumed as case study to estimate the influence of three dimensions linked with occupant behaviour – management of the thermostat, management of the heating system, variation of building characteristics – on energy heating consumption. The results show that, while the occupant behaviour influences the heating loads up to 1/3 in case of high level of building retrofit, the less the building is renovated, the higher is the behavioural impact in absolute terms of energy reduction. Therefore, in order to be effective, renovation strategies are required to design appropriate informative instruments at an early stage to support behaviour changes towards responsible energy consumption.

Abstract The central role of occupants for achieving energy savings in residential buildings is increasingly recognised. Simulation programmes able to take into account occupant behaviour are considered to be powerful tools for bridging the gap between the predicted and the actual energy consumption for new buildings. Nevertheless, the majority of residential buildings that will constitute the housing stock in 2050 have already been built today, therefore occupant behaviour and building simulation tools need to be fully exploited for supporting the renovation of existing housing stock. The aim of this paper is to explore the role of occupant behaviour modelling in supporting decision-makers dealing with the design of renovation strategies for residential buildings. An Italian multi-family public housing building is assumed as case study to estimate the influence of three dimensions linked with occupant behaviour – management of the thermostat, management of the heating system, variation of building characteristics – on energy heating consumption. The results show that, while the occupant behaviour influences the heating loads up to 1/3 in case of high level of building retrofit, the less the building is renovated, the higher is the behavioural impact in absolute terms of energy reduction. Therefore, in order to be effective, renovation strategies are required to design appropriate informative instruments at an early stage to support behaviour changes towards responsible energy consumption.

The main objective of this paper is to illustrate the current state of the art of the newborn smart gas grid concept. We provide a detailed discussion of the envisaged features of the smart gas grid, giving attention to both the related academic literature and to the ongoing world-wide projects. In doing so, we also discuss the potentialities of rethinking the smart grid paradigm from the perspective of a whole energy system, that both encompasses the electrical and the gas grid, and identify some critical key aspects that must be handled while developing the new smart energy paradigm.