• Energy Research
• other engineering and technologies close
• IT close
• FI close

Simulation of air infiltration and ventilation, and heat transfer processes of buildings are combined in a building simulation program called BUS (version 3.2). The program applies and includes an effective sparse matrix solution method for a linear set of equations. A network assumption is adopted for both air flow and thermal simulation. An iterative method, based on the SIMPLE algorithm, is used for airflow simulation, and the lumped capacitance method is selected for thermal simulation. This building simulation program BUS includes mass balance, momentum, and heat balance equations. This makes it possible to lake into consideration the interaction between ventilation and heat transfer processes, obtain more reliable simulation results than previously, and simulate time-dependent processes.

AbstractAn arc‐furnace model consisting of non‐linear, time‐varying resistance, realized by the Alternative Transients Program (ATP), is presented in this paper. It is shown that the model is appropriate for flicker investigation in electrical networks supplying arc furnaces, constituting a valid alternative to the linear arc modelling realized by amplitude modulation of voltage generators. Block diagram of the procedure for ATP modelling of the nonlinear, time‐varying arc resistance, dynamic voltage‐current characteristic of the furnace electric arc, voltage and current arc waveforms and characteristic curves of an arc furnace, obtained by ATP simulation, are presented, referring to circuit parameters taken from an actual plant and to a sinusoidal law for arc‐length time variation. Aflickermeter ATP simulation is realized to derive equivalent voltage‐variation values in agreement with the actual flicker measurements.

The performance capabilities of an axially laminated anisotropic rotor (ALA) in a high-speed synchronous reluctance motor (SynRM) were studied. A 12 kW ALASynRM was designed as an alternative to a high-speed induction motor (IM) with a solid rotor. The electromagnetic design was implemented taking into account possible issues related to the new manufacturing methods, which require thicker rotor layers than in a typical ALA. The ALASynRM shows a higher efficiency than the corresponding IM with a smooth or slitted solid rotor equipped with copper end rings. To verify the design method, a prototype IM with a smooth solid rotor was built and tested. In the analysis, it was found that, similar to IMs, in an ALASynRM a considerable part of losses takes place in the rotor despite the absence of slip-related losses in the SynRM. The distribution of eddy current losses in the ALA rotor is significantly uneven. The torque ripple in the ALASynRM is considerably larger than the corresponding ripple in IMs.

Abstract The central role of occupants for achieving energy savings in residential buildings is increasingly recognised. Simulation programmes able to take into account occupant behaviour are considered to be powerful tools for bridging the gap between the predicted and the actual energy consumption for new buildings. Nevertheless, the majority of residential buildings that will constitute the housing stock in 2050 have already been built today, therefore occupant behaviour and building simulation tools need to be fully exploited for supporting the renovation of existing housing stock. The aim of this paper is to explore the role of occupant behaviour modelling in supporting decision-makers dealing with the design of renovation strategies for residential buildings. An Italian multi-family public housing building is assumed as case study to estimate the influence of three dimensions linked with occupant behaviour – management of the thermostat, management of the heating system, variation of building characteristics – on energy heating consumption. The results show that, while the occupant behaviour influences the heating loads up to 1/3 in case of high level of building retrofit, the less the building is renovated, the higher is the behavioural impact in absolute terms of energy reduction. Therefore, in order to be effective, renovation strategies are required to design appropriate informative instruments at an early stage to support behaviour changes towards responsible energy consumption.

The main objective of this paper is to illustrate the current state of the art of the newborn smart gas grid concept. We provide a detailed discussion of the envisaged features of the smart gas grid, giving attention to both the related academic literature and to the ongoing world-wide projects. In doing so, we also discuss the potentialities of rethinking the smart grid paradigm from the perspective of a whole energy system, that both encompasses the electrical and the gas grid, and identify some critical key aspects that must be handled while developing the new smart energy paradigm.

Abstract Intermittent renewable energy generation, which is determined by weather conditions, is increasing in power markets. The efficient integration of these energy sources calls for flexible participants in smart power grids. It has been acknowledged that a large, underutilized, flexible resource lies on the consumer side of electricity generation. Despite the recently increasing interest in demand flexibility, there is a gap in the literature concerning the incentives for consumers to offer their flexible energy to power markets. In this paper, we examine a virtual power plant concept, which simultaneously optimizes the response of controllable electric hot water heaters to solar power forecast error imbalances. Uncertainty is included in the optimization in terms of solar power day-ahead forecast errors and balancing power market conditions. We show that including solar power imbalance minimization in the target function changes the optimal hot water heating profile such that more electricity is used during the daytime. The virtual power plant operation decreases solar power imbalances by 5–10% and benefits the participating households by 4.0–7.5 € in extra savings annually. The results of this study indicate that with the number of participating households, while total profits increase, marginal revenues decrease.

Abstract In this paper, a general mathematical model for the dynamic simulation of a single-effect LiBr/water absorption chiller is presented. The model is based on mass and energy balances applied to the internal components of the machine, and it accounts for the non-steady behaviour due to thermal and mass storage in the components. The validation of the mathematical model is performed through experimental data collected on a commercial small-capacity water-cooled unit. Due to the peculiar technology adopted in the real chiller, a special effort was made to identify the appropriate values of the main physical parameters. The validation of the model is based on the values of the water temperature at the outlet of the machine, as no measurement inside the machine was possible; anyway, a consistency analysis applied to the internal parameters is also presented. The agreement between experimental and simulated results is very good, both on a daily and on a seasonal basis.