• Energy Research
• Closed Access close
• Open Source close
• 7. Clean energy close
• 12. Responsible consumption close
• 2. Zero hunger close
• IN close
• IT close

Abstract The reverse flat-plate collector is a non-concentrating collector. It can collect solar heat at high temperatures which cannot be achieved by conventional non-concentrating collectors. In this paper, the authors have proposed a number of modified versions of the originally proposed reverse flat-plate collector. The new designs are of single, as well as double, absorber type. The thermal performance of these modified reverse flat-plate collectors is compared with that of a single absorber reverse flat-plate collector, as well as with the corresponding normal flat-plate collector. It is found that the new design having two absorbers gives the best thermal performance as compared with other configurations. The analytical models presented in this paper very well describe the experimental results.

Abstract In this work addition of ethanol to high viscosity jatropha methyl ester (JME) through port injection is investigated in order to determine its effect fuel viscosity reduction on diesel engine performance. In addition to viscosity alteration, the impact of ethanol addition on combustion characteristics such as combustion duration, ignition delay and emissions levels from diesel engines fuelled with blends of ethanol, diesel and JME is studied in particular. It is found that blending of oxygenated fuels with diesel modifies the chemical structure and physical properties which again alter the engine operating conditions, combustion parameters and emissions levels. However, the injection of only 5% ethanol through port injection allows for a total of 25% blending of biofuels into diesel yet keeping the fuel characteristics close to that of conventional diesel. However, both experimental and numerical results show that ethanol addition in JME blended diesel results in a slight increase in fuel consumption and thermal efficiency for the same power outputs as that of conventional diesel fuel. Also, the combustion characteristics with ethanol addition include improved maximum in-cylinder peak pressure, cumulative heat release (CHR) rate of heat release (ROHR), in-cylinder peak temperature and combustion duration. Regarding emission characteristics the experimental results show significant reduction in smoke, carbon monoxide (CO) and total hydrocarbon (THC) emissions with extended oxygen mass percentage in the fuel at higher engine loads. However, oxides of nitrogen (NOx) emissions are found to increase at high loads although the common tradeoff between smoke and NOx is found to be more prominent for the oxygenated fuels.

In this study, levulinic acid (LA) was produced from rice straw biomass in co-solvent biphasic reactor system consisting of hydrochloric acid and dichloromethane organic solvent. The modified protocol achieved a 15% wt LA yield through the synergistic effect of acid and acidic products (auto-catalysis) and the designed system allowed facile recovery of LA to the organic phase. Further purification of the resulting extractant was achieved through traditional column chromatography, which yielded a high purity LA product while recovering ∼85% wt. Upon charcoal treatment of the resultant fraction generated an industrial grade target molecule of ∼99% purity with ∼95% wt recovery. The system allows the solvent to be easily recovered, in excess of 90%, which was shown to be able to be recycled up to 5 runs without significant loss of final product concentrations. Overall, this system points to a method to significantly reduce manufacturing cost during large-scale LA preparation.

According to the renewable energy directive 2009/28/EC, the European Union Member States should increase by 2020 the use of renewable energy to 20% of gross final energy consumption and to reach a mandatory share of 10% renewable energy in the transport sector. This study aims to quantify the impact of 2020 bioenergy targets on the land use in the EU, based on the projections of the National Renewable Action Plans in four scenarios: Scenario 1. Bioenergy targets according to NREAPs; Scenario 2. Bioenergy targets according to NREAPs, no second generation biofuels; Scenario 3. Bioenergy targets according to NREAPs, reduced import of biofuels and bioliquids; Scenario 4. Bioenergy targets according to NREAPs, high imports of biofuels and bioliquids. This study also considers the credit for co-products generated from biofuel production. The analysis reveals that the land used in the EU for bioenergy would range between 13.5 Mha and 25.2 Mha in 2020. This represent between 12.2% and 22.5% of the total arable land used and 7.3% and 13.5% of the Utilised Agricultural Area (UAA). In the NREAPS scenario, about 17.4 Mha would be used for bioenergy production, representing 15.7% of arable land and 9.4% of UAA. The increased demand from biofuels would lead to an increased generation of co-products, replacing conventional fodder for animal feed. Considering the co-products, the land used for bioenergy would range between 8.8 Mha and 15.0 Mha in 2020 in the various scenarios. This represent between 7.9% and 13.3% of the total arable land used in the EU and 4.7% and 8.0% of the UAA. In the NREAPS scenario, when co-products are considered, about 10.3 Mha would be used for biofuels, bioliquids and bioenergy production, representing 9.3% of arable land and 5.6% of agricultural land. This study further provides detailed data on the impact on land use in each Member State.

AbstractAn arc‐furnace model consisting of non‐linear, time‐varying resistance, realized by the Alternative Transients Program (ATP), is presented in this paper. It is shown that the model is appropriate for flicker investigation in electrical networks supplying arc furnaces, constituting a valid alternative to the linear arc modelling realized by amplitude modulation of voltage generators. Block diagram of the procedure for ATP modelling of the nonlinear, time‐varying arc resistance, dynamic voltage‐current characteristic of the furnace electric arc, voltage and current arc waveforms and characteristic curves of an arc furnace, obtained by ATP simulation, are presented, referring to circuit parameters taken from an actual plant and to a sinusoidal law for arc‐length time variation. Aflickermeter ATP simulation is realized to derive equivalent voltage‐variation values in agreement with the actual flicker measurements.

Abstract The central role of occupants for achieving energy savings in residential buildings is increasingly recognised. Simulation programmes able to take into account occupant behaviour are considered to be powerful tools for bridging the gap between the predicted and the actual energy consumption for new buildings. Nevertheless, the majority of residential buildings that will constitute the housing stock in 2050 have already been built today, therefore occupant behaviour and building simulation tools need to be fully exploited for supporting the renovation of existing housing stock. The aim of this paper is to explore the role of occupant behaviour modelling in supporting decision-makers dealing with the design of renovation strategies for residential buildings. An Italian multi-family public housing building is assumed as case study to estimate the influence of three dimensions linked with occupant behaviour – management of the thermostat, management of the heating system, variation of building characteristics – on energy heating consumption. The results show that, while the occupant behaviour influences the heating loads up to 1/3 in case of high level of building retrofit, the less the building is renovated, the higher is the behavioural impact in absolute terms of energy reduction. Therefore, in order to be effective, renovation strategies are required to design appropriate informative instruments at an early stage to support behaviour changes towards responsible energy consumption.

The main objective of this paper is to illustrate the current state of the art of the newborn smart gas grid concept. We provide a detailed discussion of the envisaged features of the smart gas grid, giving attention to both the related academic literature and to the ongoing world-wide projects. In doing so, we also discuss the potentialities of rethinking the smart grid paradigm from the perspective of a whole energy system, that both encompasses the electrical and the gas grid, and identify some critical key aspects that must be handled while developing the new smart energy paradigm.

Abstract This paper aims to present a feasibility study of the innovative plant for methanol synthesis from carbon dioxide-sequestered by fossil fuel power plant and hydrogen, which is produced by water electrolyzer employing the over-production on the electrical grid. The thermo-economic analysis is performed in the framework of the MefCO2 H2020 EU project and it is referred to the German economic scenario, properly taking into account the real market costs and cost functions for different components of the plant. Three different plant capacities for methanol production (4000 10,000 and 50,000 ton/year) have been investigated, assuming an average cost for electrical energy to feed electrolysers and analyzing the influence of the most significant parameters (oxygen selling option, methanol selling price and electrolysers’ capital cost) on the profitability of the plant. The analysis has been performed in W-ECoMP, software for the thermo-economic analysis and plant optimization developed by the University of Genoa.