• Energy Research
• Open Access close
• Open Source close
• Embargo close
• 13. Climate action close
• 11. Sustainability close
• 15. Life on land close
• IT close
• NL close

Pyroelectric energy harvesting has the ability to transform wasted heat into useful energy and as such has a potential to create “green” energy from freely available sources such as ambient temperature changes, and contribute to the fight against climate change. Current pyroelectrics applications are limited to low-power electronics, portable systems or tasks needing only very low range of power (μW–mW). Developing further this highly promising technology should ultimately lead to the creation of more powerful, autonomous and self-powered electronic devices that could one day use to recycle currently “lost” thermal energy to power electronic devices in both domestic and industrial settings. To the best of our knowledge, hexagonal phase ZnS (wurtzite ZnS) has not been studied as a possible energy harvesting pyroelectric material despite w-ZnS being isostructural to the well-exploited and widely praised hexagonal ZnO [1]. In addition, the Tc temperature (1020 ˚C for bulk material) is high enough for ZnS that it has the ability to operate at higher temperature that are good match with the working temperature of power plants and automobiles, and hence w-ZnS ceramics should have a potential to be used in pyroelectric harvesters of waste heat coming from those activities [2]. Here we report on the pyroelectric output registered for a wurtzite phase ZnS ceramic fabricated as part of our project. To probe the pyroelectric output for a w-ZnS ceramic a simple device (a “pyro-cell”) was created by evaporating gold electrods on both sides of a ceramic sample, which was mounted on a Cu-metalized rectangular insulating base (vetronite) using silver paint. This device is stable from room temperature up to approximately 180°C. Two different heating and cooling testing set-ups were established: Set-up n°1 used an industrial scale laser, providing a source with fast temperature change, and Set-up n°2 had a standard lab hot plate heating element, providing a much slower temperature change. The characterization required an accurate measurement of the currents of the order of 10-9 A. In addition, using the Pyroelectric Test System (PK‐SPIV17T, State College, PA, USA) with a Keithley 6517 B Picoammeter, we were able to measure the pyroelectric coefficient and monitor its change at different frequencies as a function of temperature from 20 °C up to 150° C, with a heating rate of between 2 and 10 °C/min. Figure 1: Pyroelectric current measurements on an ZnS ceramic sample, using testing set-up n°1. The horizontal axis shows the time (seconds). References [1] Y. Yang, W. Guo, K.C. Pradel, G. Zhu, Y. Zhou, Y. Zhang, Y. Hu, L. Lin, Z. Lin Wang, “Pyroelectric Nanogenerators for Harvesting Thermoelectric Energy”, Nano Lett, 12 (6), 2012, 2833–2838 [2] L.A. Chavez, F.O. Zayas Jimenez, B.R. Wilburn, L.C. Delfin, H. Kim, N. Love, Y. Lin, “Characterization of Thermal Energy Harvesting Using Pyroelectric Ceramics at Elevated Temperatures”, Energy Harvesting and Systems, 5(1-2), 2018, 3–10 This project was also partially supported by the Piano triennale di realizzazione 2019-2021 della ricerca di sistema elettrico nazionale – Progetto 1.3 Materiali di frontiera per usi energetici (C.U.P. code: I34I19005780001).

Synthesis of cork-derived ceria ecoceramic, an emerging porous catalyst, for enhancing solar thermochemical water splitting.

Predicting the potential habitat of species under both current and future climate change scenarios is crucial for monitoring invasive species and understanding a species' response to different environmental conditions. Frequently, the only data available on a species is the location of its occurrence (presence-only data). Using occurrence records only, two models were used to predict the geographical distribution of two destructive invasive termite species, Coptotermes gestroi (Wasmann) and Coptotermes formosanus Shiraki. The first model uses a Bayesian linear logistic regression approach adjusted for presence-only data while the second one is the widely used maximum entropy approach (Maxent). Results show that the predicted distributions of both C. gestroi and C. formosanus are strongly linked to urban development. The impact of future scenarios such as climate warming and population growth on the biotic distribution of both termite species was also assessed. Future climate warming seems to affect their projected probability of presence to a lesser extent than population growth. The Bayesian logistic approach outperformed Maxent consistently in all models according to evaluation criteria such as model sensitivity and ecological realism. The importance of further studies for an explicit treatment of residual spatial autocorrelation and a more comprehensive comparison between both statistical approaches is suggested.

Abstract This literature review was built upon recently published articles on Life Cycle Assessments (LCAs) of agricultural biogas plants, to: enhance understanding of the relevant literature in the field and the related question by readers worldwide. It was designed to highlight methodological issues and impact indicators, which best represent this research field; consequently, they should be considered in performing environmental assessments of agro-biogas derived energy systems. The literature review highlighted the wide variability of environmental results due to the ways the feedstock mixtures were produced, managed, and supplied; and due to the regions in which the anaerobic digesters were located and operated. Differences were found to be related to the aim and function of the study and to the methodological approach used, especially for the development of the environmental impact assessments. Other differences resulted from the ways the energy produced was utilised, whether it was used as an input to the natural gas national grid, and/or if it was used within the production system. The authors of this review concluded that, although much progress has been made, many unsolved challenges and methodological choices must be addressed to further improve the robustness of LCA in relation to AD and to related approaches.

From the comparison of regulations and/or standards for the organic, conventional and/or integrated citrus production method and a voluntary certification, it emerges that farms certified with voluntary non-regulated certification systems, such as the IFA FV GLOBALG.A.P, are obliged to take into account the highest number of aspects, reported in a more complete register, than the organic ones. Moreover, this is also supported by a continuous-time planned process of revision and updating of the applicable versions of the standard. The environmental impact of the food production, the safety aspects of food products, as well as the health, ethics, and safety aspects of workers, are largely considered and inspected in the GLOBALG.A.P., while the organic system, despite the IFOAM suggestions and indications, is only considered partially. This means that, from a practical point of view, the organic product can be considered “clean and safe”, but not more environmentally friendly than the GLOBALG.A.P. products.

Abstract European and Italian standards establish high levels of energy performance of buildings that have to be designed considering their energy balance near zero. To achieve this goal, the reduction of energy demand, attainable by improving energy efficiency of the construction, and the use of renewable energy available both on site and off site are effective solutions to be applied. In particular, in buildings that use energy produced from renewable sources, due to their unstable and unpredictable nature, having the right strategy to compensate the variations is essential. A technical solution reevaluated as a consequence of passive design principles, is to provide an adequate thermal inertia in order to store energy when it is offered and to use it when the source is not available. In these cases, the ability of construction elements to retain heat becomes fundamental as they contribute to maintain internal comfort conditions. This paper aims to investigate how various types of heating and cooling systems, based on different modes of heat transfer, are able to interact differently with the thermal mass of the building, producing a different level of its activation. The investigation considers a case study used to carry out dynamic simulation by means of DesignBuilder which is a user interface of EnergyPlus. The model consists of a building with elementary geometry and a single thermal zone, delimited by walls with outside thermal insulation and a heat accumulation layer inside. The variation of the internal temperature by using different types of conditioning system is analyzed in order to individuate the technology that takes the greatest advantages from the thermal mass.