• Energy Research
• 2016-2025close
• Closed Access close
• Restricted close
• Embargo close
• AU close
• KR close
• JP close

Abstract The accurate information of the thermal stresses and temperature in isotropic elastic solids is the key for many engineering applications. At present the classical linear coupled theory of thermoelasticity deduced with the assumptions of small temperature changes is widely used to solve the thermoelastic problems in engineering. In this paper, to describe the thermoelastic behavior in isotropic solids undergoing large temperature changes more accurately, the novel coupled models of thermoelasticity and the corresponding finite element models have been presented explicitly and validated by experimental measurement. The effect of large temperature changes on the solutions of thermoelastic problems is discussed. For the heat transfer process, if the isotropic elastic solids will expand when heated and contract when cooled and the condition d E E d T · σ i j E − δ i j 1 − 2 ν α 0 can be met in the context of small deformations, the effect of large temperature changes can be regarded as increasing the specific heat. The proposed models are applied to solve two thermoelastic problems. From the obtained numerical results, the effect of large temperature changes will increase with the amplitude of temperature change and may be considerably even when the temperature changes slowly.

Abstract Double and added double stage organic Rankine cycle systems are configured to recover exhaust gas waste heat of dual fuel engines. To evaluate the performance of the models proposed here, energy, exergy and economic analyses are performed. Several working fluids are evaluated for recommendation for double and added double stage organic Rankine cycle systems. In the double stage organic Rankine cycle, cycle 1 and cycle 2 are connected in parallel. Working fluids R123, R141b, and R601 are used in cycle 1, and R245fa, R236ea, and R1233zd in cycle 2. In the double stage organic Rankine cycle, the working fluid combinations of R601-R1233zd, R601-R245fa and R123-R245fa show better performance when considering power, heat transfer area and payback period, which are 1760 kW, 2108.9 m2 and 4.21 year, respectively for R601-R245fa. In the added double stage organic Rankine cycle, cycle 1 and cycle 2 are connected in two stages and cycle 1 and cycle 3 in parallel. The net power of the working fluid combinations of R123-R245fa and R123-R1233zd are 1799 kW and 1782 kW, respectively, which are higher than those of the others. Further, for R123-R245fa, the heat transfer area and payback period are 3352 m2 and 6.20 year, respectively, which is better compared to those of other working fluid combinations.

Low-salinity water injection emerges to be a cost-effective and environmentally friendly enhanced oil recovery technique. Furthermore, additives, such as the surfactant and nanoparticles in combina...

Interconnectivity and interoperability are very important features in the development of integrated energy management systems for industrial facilities. A simple and common strategy for exchanging energy-related information among the entities in a facility is currently lacking. To this end, the purpose of this study is to present an IoT-based communication framework with a common information model to facilitate the development of a demand response (DR) energy management system for industrial customers. Additionally, we developed and implemented an IoT-based energy-management platform based on a common information model and open communication protocols, which takes advantage of integrated energy supply networks to deploy DR energy management in an industrial facility. The experimental results of this study demonstrate that the proposed platform can not only improve the interconnectivity of the entities in industrial energy management systems but also reduce the energy costs of industrial facilities.

Abstract Date biomass is a carbon-rich renewable resource that can be considered a potential carbon-rich substrate for energy generation over anaerobic digestion (AD). However, due to its complex nature, appropriate pretreatment is necessary to achieve a higher methane yield. Hence, the current study was envisioned to evaluate the influence of three different pretreatment strategies, namely acid, alkali, and hydrothermal pretreatment on biochemical methane potential (BMP) of seven diverse sorts of Algerian date biomass, namely Pedicels, Fibrilium, Petiole, Fruit bunch, Spath, Palm, and its mixture. Among all the pretreatment conditions, alkaline pretreatment highly influenced the lignin composition of date biomass and showed higher BMP. Among all sorts of biomass, higher BMP was detected through Palm as 295.9 mL CH4/g-TS, whereas the lowest BMP values were recorded with Petiole as 226.74 mL CH4/g-TS. Among all the experimental variations, ammonium pretreated Palm biomass documented the highest substrate conversion efficiency (63.80%), which correlates well with the observed higher BMP values. Nevertheless, there was a very marginal improvement in BMP detected in the case of other pretreatment strategies compared to alkaline pretreatment. This might be due to the efficacy of the applied pretreatment method on delignification of date biomass.

Abstract This study demonstrates the possibility to use energy-cost optimal building designs based on life cycle approach. There is a lack of studies that cover the comprehensive assessment of both embodied energy (EE) and operational energy (OE) in a single optimization problem. The primary goal of the current study is to compare the optimized results of using OE+EE together and OE only. The optimization is performed on a case study building (townhouse) in Finland with three structural alternatives (i.e., reinforced concrete (RC); cross-laminated timber (CLT) and Steel). Different options for insulation thickness of external wall, roof, floor and window types were considered as decision variables as the scope of the present study is on building envelope. The objectives of the optimization are to minimize life cycle energy (LCE) and life cycle costs (LCC). The LCE difference between the most and least energy efficient solution on the pareto front is greater in case of the OE optimization, compared to OE+EE optimization. For all studied structures, the EE of the optimal solutions from OE+EE optimization ranges 16%–23% of LCE. Many of the non-dominated optimal solutions obtained from the OE+EE optimization shows a higher U-value for the building envelope components compared to the optimal solutions from the OE optimization. A relationship between both OE and EE with the overall thermal resistance of the building envelope is discussed to obtain a deeper understanding of such differences in U-value for the optimal solutions obtained from the OE+EE and OE optimization.

Abstract Energy harvesting in natural environment has attracted a great deal of attention to generate stable and continuous electrical energy. In this work, we proposed an advanced pyroelectric energy harvesting system by using form-stable phase change material (PCM) composites. The PCM composite connected pyro-electrode generated electrical polarization due to the change of external environment. Polyethylene glycol (PEG) and 1-tetradecanol (1-TD) composites with different phase transition field induced the temperature difference during light-on/-off process. Poly(vinylidene difluoride) (PVDF) was utilized for pyroelectric energy harvesting. The PVDF based pyro-electrode was applied changing the conditions of solar light irradiation and heat air flow. The PCM composites controlled the temperature fluctuation effectively and generated stable output electrical voltage and current. Numerical simulation was carried out to provided in-depth insight into the underlying physics of the system. We envisage that the developed thermal energy harvesting system can pave a way towards high-throughput and sustainable energy harvesting.

Abstract In this work, earth-abundant CZTSSe thin film solar cells were fabricated by sulfo-selenization of the Mo/Zn/Cu/Sn/Cu metallic precursors. The influences of morphological and compositional properties of the absorbers on performance of solar cells were investigated by tuning Cu content in the films. The Raman analysis showed that absorbers consist of a kesterite CZTSSe phase with ZnSe as a minor secondary phase. X-ray photoelectron spectroscopy (XPS) analyses revealed that the surfaces are Cu depleted and Zn enriched compared with the bulk composition of the absorbers. The results indicate that during sulfo-selenization the Cu diffused into the film and the Zn towards the film surface. The performance of the solar cells initially improved with the increasing of the Cu content and then decreased. By tuning the Cu content in the absorbers, the minority-carrier life time improved from 0.8 to 1.6 ns. The power conversion efficiency increased from 5.1 to 8.03% with fine controlling of Cu composition of the CZTSSe absorbers. The diode-ideality factors are higher than 2, suggesting an increased interfacial recombination in the devices. The high ideality-factors A and low minority carrier life times may originate from surface and bulk related defects, which in turn limits the Voc and the achievable high conversion efficiency for the CZTSSe thin film solar cells.