• Energy Research
• Restricted close
• Open Source close
• other engineering and technologies close
• NL close
• US close

It is well known that the efficiency of PV modules decreases with increasing module temperatures. Many studies have paid attention to the development and validation of heuristic models to calculate the PV module temperature in higher latitudes, however only a few focus on the thermal behaviour of PV modules in tropical regions of the world, where constantly high temperatures prevail. Also, little is known about the effect of including wind speed in these thermal models. This study evaluates three of such models - one that excludes wind, and two others including the wind influence - using hourly data for two tropical locations. Results show that the average hourly wind speeds in Singapore and Jayapura (Indonesia) are low and therefore the influence of the wind on the PV module temperature is minor. The three evaluated models produce about the same results with RMSE between 1.5-3.8 °C during daytime, which corresponds to a deviation in power output in the range of 0.3-1.6 %, depending on the PV module technology.

It is well known that the efficiency of PV modules decreases with increasing module temperatures. Many studies have paid attention to the development and validation of heuristic models to calculate the PV module temperature in higher latitudes, however only a few focus on the thermal behaviour of PV modules in tropical regions of the world, where constantly high temperatures prevail. Also, little is known about the effect of including wind speed in these thermal models. This study evaluates three of such models - one that excludes wind, and two others including the wind influence - using hourly data for two tropical locations. Results show that the average hourly wind speeds in Singapore and Jayapura (Indonesia) are low and therefore the influence of the wind on the PV module temperature is minor. The three evaluated models produce about the same results with RMSE between 1.5-3.8 °C during daytime, which corresponds to a deviation in power output in the range of 0.3-1.6 %, depending on the PV module technology.

<div class="section abstract"><div class="htmlview paragraph">The introduction of new light-duty vehicle emission limits to comply under real driving conditions (RDE) is pushing the diesel engine manufacturers to identify and improve the technologies and strategies for further emission reduction. The latest technology advancements on the after-treatment systems have permitted to achieve very low emission conformity factors over the RDE, and therefore, the biggest challenge of the diesel engine development is maintaining its competitiveness in the trade-off “CO₂-system cost” in comparison to other propulsion systems. In this regard, diesel engines can continue to play an important role, in the short-medium term, to enable cost-effective compliance of CO₂-fleet emission targets, either in conventional or hybrid propulsion systems configuration. This is especially true for large-size cars, SUVs and light commercial vehicles.</div><div class="htmlview paragraph">In this framework, a comprehensive approach covering the whole powertrain is of primary importance in order to simultaneously meet the performance, efficiency, noise and emission targets, and therefore, further development of the combustion system design and injection system represent important levers for additional improvements. For this purpose, a dedicated 0.5 dm³ single-cylinder engine has been developed and equipped with, a state-of-the-art Euro 6 combustion system, and an advanced common rail fuel injection system (FIS) offering higher flexibility in terms of injection strategy and higher quantity accuracy. Three injector nozzles with different hydraulic flow rates (HF) have been selected and employed for the overall combustion process optimization.</div><div class="htmlview paragraph">The optimization has been performed by means of an extensive DoE-based test campaign in which the engine and FIS operating parameters have been parametrized with the aim to carry out a proper combination in terms of HF and injection strategy. The results at partial load conditions evidence significant advantages in applying an advanced injection pattern, while the HF reduction can significantly improve the smoke emission and combustion noise without fuel consumption penalties. Therefore, a proper combination and optimization of the HF and injection strategy can provide low noise and engine-out smoke while maintaining the rated power performance targets.</div></div>

<div class="section abstract"><div class="htmlview paragraph">The introduction of new light-duty vehicle emission limits to comply under real driving conditions (RDE) is pushing the diesel engine manufacturers to identify and improve the technologies and strategies for further emission reduction. The latest technology advancements on the after-treatment systems have permitted to achieve very low emission conformity factors over the RDE, and therefore, the biggest challenge of the diesel engine development is maintaining its competitiveness in the trade-off “CO₂-system cost” in comparison to other propulsion systems. In this regard, diesel engines can continue to play an important role, in the short-medium term, to enable cost-effective compliance of CO₂-fleet emission targets, either in conventional or hybrid propulsion systems configuration. This is especially true for large-size cars, SUVs and light commercial vehicles.</div><div class="htmlview paragraph">In this framework, a comprehensive approach covering the whole powertrain is of primary importance in order to simultaneously meet the performance, efficiency, noise and emission targets, and therefore, further development of the combustion system design and injection system represent important levers for additional improvements. For this purpose, a dedicated 0.5 dm³ single-cylinder engine has been developed and equipped with, a state-of-the-art Euro 6 combustion system, and an advanced common rail fuel injection system (FIS) offering higher flexibility in terms of injection strategy and higher quantity accuracy. Three injector nozzles with different hydraulic flow rates (HF) have been selected and employed for the overall combustion process optimization.</div><div class="htmlview paragraph">The optimization has been performed by means of an extensive DoE-based test campaign in which the engine and FIS operating parameters have been parametrized with the aim to carry out a proper combination in terms of HF and injection strategy. The results at partial load conditions evidence significant advantages in applying an advanced injection pattern, while the HF reduction can significantly improve the smoke emission and combustion noise without fuel consumption penalties. Therefore, a proper combination and optimization of the HF and injection strategy can provide low noise and engine-out smoke while maintaining the rated power performance targets.</div></div>

The aim of the paper is to study the influence of the power transformer on signal transmission in the case of a power line communication (PLC) system in a overhead Medium Voltage (MV) power network. A model of the PLC system was carried out by means of the Simulink® software. A distributed parameter MV overhead line, two power transformers, the signal coupling interface of a ST7540 FSK powerline transceiver were included in the model. The performances of the complete PLC communication system are evaluated for different line lengths by means of the attenuation computed as ratio between the received and transmitted voltage signals. © 2011 IEEE.

The aim of the paper is to study the influence of the power transformer on signal transmission in the case of a power line communication (PLC) system in a overhead Medium Voltage (MV) power network. A model of the PLC system was carried out by means of the Simulink® software. A distributed parameter MV overhead line, two power transformers, the signal coupling interface of a ST7540 FSK powerline transceiver were included in the model. The performances of the complete PLC communication system are evaluated for different line lengths by means of the attenuation computed as ratio between the received and transmitted voltage signals. © 2011 IEEE.

AbstractThe surface oxygen exchange on oxides with high oxygen ion mobility is modelled with a two step reaction with adsorbed mono-atomic oxygen species as intermediate. Interpretation of the Po2 dependence of the exchange rates, following from this model, indicates that these adsorbed oxygen atoms are singly charged.For the stabilized δ-Bi2O3 solid electrolyte a good agreement has been found between the isotope exchange model and the electrochemical study of the oxygen exchange using gold electrodes. For the mixed La-Sr cobaltite perovskite a change in the surface exchange reaction is observed going from room temperature to 600°C. Indications are that above 450°C the bulk exchange is rate limiting with a (Po2)−1 dependence while below this temperature it is assumed that the dissociative adsorption is rate limiting with a (Po2)1/2 dependence.

AbstractThe surface oxygen exchange on oxides with high oxygen ion mobility is modelled with a two step reaction with adsorbed mono-atomic oxygen species as intermediate. Interpretation of the Po2 dependence of the exchange rates, following from this model, indicates that these adsorbed oxygen atoms are singly charged.For the stabilized δ-Bi2O3 solid electrolyte a good agreement has been found between the isotope exchange model and the electrochemical study of the oxygen exchange using gold electrodes. For the mixed La-Sr cobaltite perovskite a change in the surface exchange reaction is observed going from room temperature to 600°C. Indications are that above 450°C the bulk exchange is rate limiting with a (Po2)−1 dependence while below this temperature it is assumed that the dissociative adsorption is rate limiting with a (Po2)1/2 dependence.