• Energy Research
• 2021-2025close
• DE close
• PL close
• AT close

AbstractDecarbonising the energy system requires high shares of variable renewable generation and sector coupling like power to heat. In addition to heat supply, heat pumps can be used in future energy systems to provide flexibility to the electricity system by using the thermal storage potential of the building stock and buffer tanks to shift electricity demand to hours of high renewable electricity production. Bridging the gap between two methodological approaches, we coupled a detailed building technology operation model and the open-source energy system model Balmorel to evaluate the flexibility potential that decentral heat pumps can provide to the electricity system. Austria in the year 2030 serves as an example of a 100% renewable-based electricity system (at an annual national balance). Results show that system benefits from heat pump flexibility are relatively limited in extent and concentrated on short-term flexibility. Flexible heat pumps reduce system cost, CO2 emissions, and photovoltaics and wind curtailment in all scenarios. The amount of electricity shifted in the assessed standard flexibility scenario is 194 GWhel and accounts for about 20% of the available flexible heat pump electricity demand. A comparison of different modelling approaches and a deterministic sensitivity analysis of key input parameters complement the modelling. The most important input parameters impacting heat pump flexibility are the flexible capacity (determined by installed capacity and share of control), shifting time limitations, and cost assumptions for the flexibility provided. Heat pump flexibility contributes more to increasing low residual loads (up to 22% in the assessed scenarios) than decreasing residual load peaks. Wind power integration benefits more from heat pump flexibility than photovoltaics because of the temporal correlation between heat demand and wind generation.

Progressive urban density affects city centers especially and results in growing congestion, lack of parking spaces, and increasing environmental costs of transportation, causing increased air pollutant emissions and noise. These phenomena reduce the attractiveness of the city and result in a degradation of the quality of life for its residents. In light of these phenomena, there is a clear need for intelligent management of urban space using new technologies that would be complementary to existing intelligent transportation systems. Expanding information resources obtained from mobile cameras will have a positive impact on increasing the efficiency of transportation management and use of limited space in city centers. It will also have an impact on reducing external transport costs and increasing the quality of logistics services provided in the city. The main aim of the paper is to develop a concept of a transport management system in cities using mobile vision systems mounted on unmanned aerial vehicles. The model will concern the cases of lane occupation by freight vehicles and the analysis of parking spaces in the city in order to improve their management. The results of the developed model will contribute to the automation of the parking space management process and increase the efficiency of the use of city parking space resources.

This deliverable includes the methodology in EnergyPROSPECTS for an in-depth study of energy citizenship. It features the criteria used for selecting the cases for indepth study, the list of cases selected for in-depth study as well as key research foci and empirical research questions.

This manuscript presents performed laboratory studies and the analysis of the impact of current shunt values used in the differential connection on the wideband metrological performance of inductive current transformers. Moreover, a comparison of the accuracy of wideband and 50 Hz-type inductive current transformers in the specified frequency range from 50 Hz to 5 kHz is presented. The main factor which may influence the wideband accuracy of inductive current transformers is the phenomenon of self-generation. This causes rapid changes in the accuracy, and simultaneously causes the most positive and the most negative values of current error and phase displacement. To evaluate the metrological performance in the differential measurement setup for higher harmonics of the distorted current, a digital acquisition board was used. Obtained results show that if proper values of current shunt resistance are chosen, such devices may be used to evaluate the wideband accuracy of inductive current transformers. The results indicate that the typical units designed for the transformation of sinusoidal current with a frequency of 50 Hz can achieve a comparable metrological performance to that of the wideband inductive current transformer.

Lithium-ion batteries exhibit a dynamic voltage behaviour depending nonlinearly on current and state of charge. The modelling of lithium-ion batteries is therefore complicated and model parametrisation is often time demanding. Grey-box models combine physical and data-driven modelling to benefit from their respective advantages. Neural ordinary differential equations (NODEs) offer new possibilities for grey-box modelling. Differential equations given by physical laws and NODEs can be combined in a single modelling framework. Here we demonstrate the use of NODEs for grey-box modelling of lithium-ion batteries. A simple equivalent circuit model serves as a basis and represents the physical part of the model. The voltage drop over the resistor–capacitor circuit, including its dependency on current and state of charge, is implemented as a NODE. After training, the grey-box model shows good agreement with experimental full-cycle data and pulse tests on a lithium iron phosphate cell. We test the model against two dynamic load profiles: one consisting of half cycles and one dynamic load profile representing a home-storage system. The dynamic response of the battery is well captured by the model.

Mixing under high pressure conditions plays a central role in several engineering applications, such as direct-injection engines and liquid rocket engines. Numerical flow simulations have become a complementary tool to study the mixing process under these conditions but require complex thermodynamic modeling as well as validation with accurate experimental data. For this reason, we use experiments of supercritical single-phase jet mixing from the literature, where the mixing is quantified by the mixture speed of sound, as a reference for our work. We here focus on the thermodynamic modeling of multi-component flows under high pressure conditions and the analytical calculation of the mixture speed of sound. Our thermodynamic model is based on cubic equations of state extended for multi-components. Using an extension of OpenFOAM, we perform large-eddy simulations of hexane and pentane injections and compare our results with the experimentally measured mixture speed of sound at specific positions. The simulation results show the same characteristic trends, indicating that the mixing effects are well reproduced in the simulations. Additionally, the effect of the sub-grid scale modeling is assessed by comparing results using different models (Smagorinsky, Vreman, and Wall-Adapting Local Eddy-viscosity). The comprehensive simulation data presented here, in combination with the experimental data, provide a benchmark for numerical simulations of jet mixing in high pressure conditions.

AbstractClimate change may force organisms to adapt genetically or plastically to new environmental conditions. Invasive species show remarkable potential for rapid adaptation. The ovoviviparous New Zealand mud snail (NZMS),Potamopyrgus antipodarum, has successfully established across Europe with two clonally reproducing mitochondrial lineages since its arrival in the first half of the 19th century. Its remarkable variation in shell morphology was shown to be fitness relevant. We investigated the effects of temperature on shell morphology across 11 populations from Germany and the Iberian Peninsula in a common garden across three temperatures. We analyzed size and shape using geometric morphometrics. For both, we compared reaction norms and estimated heritabilities. For size, the interaction of temperature and haplotype explained about 50% of the total variance. We also observed more genotype by environment interactions indicating a higher degree of population differentiation than in shape. Across the three temperatures, size followed the expectations of the temperature‐size rule, with individuals growing larger in cold environments. Changes in shape may have compensated for changes in size affecting space for brooding embryos. Heritability estimates were relatively high. As indicated by the very low coefficients of variation for clonal repeatability (CVA), they can probably not be compared in absolute terms. However, they showed some sensitivity to temperature, in haplotype t more so than in z, which was only found in Portugal. The lowCVAvalues indicate that genetic variation among European populations is still restricted with a low potential to react to selection. A considerable fraction of the genetic variation was due to differences between the clonal lineages. The NZMS has apparently not been long enough in Europe to accumulate significant genetic variation relevant for morphological adaptation. As temperature is obviously not the sole factor influencing shell morphology, their interaction will probably not be a factor limiting population persistence under a warming climate in Europe.