• Energy Research
• Open Access close
• Closed Access close
• engineering and technology close
• EU close
• PL close

AbstractDecarbonising the energy system requires high shares of variable renewable generation and sector coupling like power to heat. In addition to heat supply, heat pumps can be used in future energy systems to provide flexibility to the electricity system by using the thermal storage potential of the building stock and buffer tanks to shift electricity demand to hours of high renewable electricity production. Bridging the gap between two methodological approaches, we coupled a detailed building technology operation model and the open-source energy system model Balmorel to evaluate the flexibility potential that decentral heat pumps can provide to the electricity system. Austria in the year 2030 serves as an example of a 100% renewable-based electricity system (at an annual national balance). Results show that system benefits from heat pump flexibility are relatively limited in extent and concentrated on short-term flexibility. Flexible heat pumps reduce system cost, CO2 emissions, and photovoltaics and wind curtailment in all scenarios. The amount of electricity shifted in the assessed standard flexibility scenario is 194 GWhel and accounts for about 20% of the available flexible heat pump electricity demand. A comparison of different modelling approaches and a deterministic sensitivity analysis of key input parameters complement the modelling. The most important input parameters impacting heat pump flexibility are the flexible capacity (determined by installed capacity and share of control), shifting time limitations, and cost assumptions for the flexibility provided. Heat pump flexibility contributes more to increasing low residual loads (up to 22% in the assessed scenarios) than decreasing residual load peaks. Wind power integration benefits more from heat pump flexibility than photovoltaics because of the temporal correlation between heat demand and wind generation.

AbstractDecarbonising the energy system requires high shares of variable renewable generation and sector coupling like power to heat. In addition to heat supply, heat pumps can be used in future energy systems to provide flexibility to the electricity system by using the thermal storage potential of the building stock and buffer tanks to shift electricity demand to hours of high renewable electricity production. Bridging the gap between two methodological approaches, we coupled a detailed building technology operation model and the open-source energy system model Balmorel to evaluate the flexibility potential that decentral heat pumps can provide to the electricity system. Austria in the year 2030 serves as an example of a 100% renewable-based electricity system (at an annual national balance). Results show that system benefits from heat pump flexibility are relatively limited in extent and concentrated on short-term flexibility. Flexible heat pumps reduce system cost, CO2 emissions, and photovoltaics and wind curtailment in all scenarios. The amount of electricity shifted in the assessed standard flexibility scenario is 194 GWhel and accounts for about 20% of the available flexible heat pump electricity demand. A comparison of different modelling approaches and a deterministic sensitivity analysis of key input parameters complement the modelling. The most important input parameters impacting heat pump flexibility are the flexible capacity (determined by installed capacity and share of control), shifting time limitations, and cost assumptions for the flexibility provided. Heat pump flexibility contributes more to increasing low residual loads (up to 22% in the assessed scenarios) than decreasing residual load peaks. Wind power integration benefits more from heat pump flexibility than photovoltaics because of the temporal correlation between heat demand and wind generation.

The paper presents an experimental study on the formation process of burden surface texture on the blast furnace throat and its influence on the radial distribution of gas flow. The study was performed with the application of blast furnaces equipped with a bell-type charging device using radio-isotope means for the control of burden surface texture (profile) and burden surface level, i.e., gamma locators for burden surface texture. The study was carried out under the conditions of an operating blast furnace in an iron and steel plant using a unique GEOTAPS system for automated control of geometric and temperature parameters of burden material surface on the blast furnace throat. The influence of the surface texture on the gas flow distribution was also investigated. The possibility of a self-stabilization effect for burden surface texture and gas flow in an operating blast furnace under suitable conditions was experimentally proven. As a result of the experimental study performed, four ways of energy-saving technology implementation were determined for the control of blast furnace melting based on the data on the burden surface texture and previously unknown regularities of surface layer formation of burden material on the throat of an operating blast furnace with a bell-type charging device. The main idea of the paper is the development of automated control for the radial distribution of burden material and gas flow using actual or predicted surface texture parameters as important intermediate factors that both describe the process and have a significant simultaneous influence on it.

The paper presents an experimental study on the formation process of burden surface texture on the blast furnace throat and its influence on the radial distribution of gas flow. The study was performed with the application of blast furnaces equipped with a bell-type charging device using radio-isotope means for the control of burden surface texture (profile) and burden surface level, i.e., gamma locators for burden surface texture. The study was carried out under the conditions of an operating blast furnace in an iron and steel plant using a unique GEOTAPS system for automated control of geometric and temperature parameters of burden material surface on the blast furnace throat. The influence of the surface texture on the gas flow distribution was also investigated. The possibility of a self-stabilization effect for burden surface texture and gas flow in an operating blast furnace under suitable conditions was experimentally proven. As a result of the experimental study performed, four ways of energy-saving technology implementation were determined for the control of blast furnace melting based on the data on the burden surface texture and previously unknown regularities of surface layer formation of burden material on the throat of an operating blast furnace with a bell-type charging device. The main idea of the paper is the development of automated control for the radial distribution of burden material and gas flow using actual or predicted surface texture parameters as important intermediate factors that both describe the process and have a significant simultaneous influence on it.

Abstract Additional experimental data concerning the kinetics of Ni-Mo codeposition were obtained by investigating cathodic polarization using a rotating disc electrode. The Ni-Mo alloys were deposited from an ammonium citrate bath. The alloy deposition was controlled by activation in the case of low values of the cathode potential and by diffusion in the case of higher values. The hydrogen discharge was found to be diffusion controlled. The inductive influence of nickel results in depolarization of the reduction of molybdenum which cannot be deposited separately. An increase in the disc rotation speed caused an increase in the maximum cathode efficiency and in the molybdenum content of the alloy.

Abstract Additional experimental data concerning the kinetics of Ni-Mo codeposition were obtained by investigating cathodic polarization using a rotating disc electrode. The Ni-Mo alloys were deposited from an ammonium citrate bath. The alloy deposition was controlled by activation in the case of low values of the cathode potential and by diffusion in the case of higher values. The hydrogen discharge was found to be diffusion controlled. The inductive influence of nickel results in depolarization of the reduction of molybdenum which cannot be deposited separately. An increase in the disc rotation speed caused an increase in the maximum cathode efficiency and in the molybdenum content of the alloy.

The energy considered as waste heat in industrial furnaces owing to inefficiencies represents a substantial opportunity for recovery by means of thermal energy storage (TES) implementation. Although conventional systems based on sensible heat are used extensively, these systems involve technical limitations. Latent heat storage based on phase change materials (PCMs) results in a promising alternative for storing and recovering waste heat. Within this scope, the proposed PCM-TES allows for demonstrating its implementation feasibility in energy-intensive industries at high temperature range. The stored energy is meant to preheat the air temperature entering the furnace by using a PCM whose melting point is 885 °C. In this sense, a heat transfer model simulation is established to determine an appropriate design based on mass and energy conservation equations. The thermal performance is analysed for the melting and solidification processes, the phase transition and its influence on heat transference. Moreover, the temperature profile is illustrated for the PCM and combustion air stream. The obtained results prove the achievability of very high temperature levels (from 700 to 865 °C) in the combustion air preheating in a ceramic furnace; so corroborating an energy and environmental efficiency enhancement, compared to the initial condition presenting an air outlet at 650 °C.

The energy considered as waste heat in industrial furnaces owing to inefficiencies represents a substantial opportunity for recovery by means of thermal energy storage (TES) implementation. Although conventional systems based on sensible heat are used extensively, these systems involve technical limitations. Latent heat storage based on phase change materials (PCMs) results in a promising alternative for storing and recovering waste heat. Within this scope, the proposed PCM-TES allows for demonstrating its implementation feasibility in energy-intensive industries at high temperature range. The stored energy is meant to preheat the air temperature entering the furnace by using a PCM whose melting point is 885 °C. In this sense, a heat transfer model simulation is established to determine an appropriate design based on mass and energy conservation equations. The thermal performance is analysed for the melting and solidification processes, the phase transition and its influence on heat transference. Moreover, the temperature profile is illustrated for the PCM and combustion air stream. The obtained results prove the achievability of very high temperature levels (from 700 to 865 °C) in the combustion air preheating in a ceramic furnace; so corroborating an energy and environmental efficiency enhancement, compared to the initial condition presenting an air outlet at 650 °C.