• Energy Research
• Open Access close
• Closed Access close
• Open Source close
• 7. Clean energy close
• 11. Sustainability close
• 6. Clean water close
• PL close

Progressive urban density affects city centers especially and results in growing congestion, lack of parking spaces, and increasing environmental costs of transportation, causing increased air pollutant emissions and noise. These phenomena reduce the attractiveness of the city and result in a degradation of the quality of life for its residents. In light of these phenomena, there is a clear need for intelligent management of urban space using new technologies that would be complementary to existing intelligent transportation systems. Expanding information resources obtained from mobile cameras will have a positive impact on increasing the efficiency of transportation management and use of limited space in city centers. It will also have an impact on reducing external transport costs and increasing the quality of logistics services provided in the city. The main aim of the paper is to develop a concept of a transport management system in cities using mobile vision systems mounted on unmanned aerial vehicles. The model will concern the cases of lane occupation by freight vehicles and the analysis of parking spaces in the city in order to improve their management. The results of the developed model will contribute to the automation of the parking space management process and increase the efficiency of the use of city parking space resources.

For economic reasons, expansions of transmission networks are based on a compromise between capital cost and security of power system operation. At the same time, the power system must withstand typical highly likely contingencies. Various emergency state control systems, also called special protections, prevent emergencies following less likely contingencies. This paper describes overloads emergency state control (OLEC) used for the alleviation of overload in transmission networks near a power plant. Such control uses the functions of automated power reduction of generating units and has been implemented for a large steam power plant. The OLEC presented here uses different methods of generation curtailment for steam generation units. A case study illustrates the efficiency of the proposed control method.

Abstract Coal gasification is accompanied with formation of tars that cause equipment problems and have to be removed from the raw gas. Our previous studies proved that nickel supported ceria-zirconia catalyst (Ni/CZ) reveals high activity towards decomposition of toluene and 1-methylnaphthalene (1-MN) via steam reforming reaction (SR). However, the components of the raw gas from coal gasification (i.e. H2, CO, CO2 and CH4) may influence the performance of Ni/CZ catalyst. The influence of particular components of the raw gas on catalyst performance during SR of model tar compounds have been studied and discussed in this paper. It has been found that H2 and CO addition to the steam reforming feed drastically decreases the activity of Ni/CZ catalyst, whereas CO2 presence enhances conversion of toluene and 1-MN mixture owing to the occurrence of dry reforming reaction (DR). It has also been observed that methane, which is present in the raw gas from coal gasification consumes partly both the H2O and CO2, causing some decrease in conversion of model tar compounds. The influence of contact time (tc) on hydrocarbons conversion and the participation of (DR) have been examined. As was observed, lower contact times lead to decrease in hydrocarbons conversion in SR, making the same participation of DR more pronounced than for higher tc values. This work proves that Ni/CZ catalyst can be used for removal of tarry compounds via the catalytic hot gas cleaning of the raw gas form coal gasification.

Energy efficiency is an increasingly important dimension of household appliances, which is why they are labeled to indicate their energy consumption. In 2020, the European Union countries changed the labeling system from the previous system: ranging from A+++ to D, to the new system: ranging from A to G, assuming it would be more transparent for the consumer. The aim of the study was to find out the extent to which consumers are aware of the new labeling system, and the impact that the new labels have (compared to the previous ones) on the perception of household appliances and consumer decision-making. For this purpose, the survey was conducted on a nationwide representative Polish sample (n = 1054). The research was partly experimental, where the same appliances were presented with new and previous energy labels. The results showed that currently most people do not identify the new energy classes. Furthermore, products with the new labels are perceived as being less energy efficient in comparison with products with the previous labels, which shows that there is some confusion among consumers in terms of the new energy efficiency labeling system.

Energy harvesting is a useful technique for various kinds of self-powered electronic devices and systems as well as Internet of Things technology. This study presents a two-degrees-of-freedom (2DOF) electromagnetic energy harvester that can use environment vibration and provide energy for small electronic devices. The proposed harvester consists of a cylindrical tube with two moving magnets suspended by a magnetic spring mechanism and a stationary coil. In order to verify the theoretical model, a prototype electromagnetic harvester was constructed and tested. The influence of key parameters, including excitation acceleration, response to a harmonic frequency sweep, and electromechanical coupling on the generated characteristics of the harvester, was investigated. The experimental and theoretical results showed that the proposed electromagnetic energy harvester was able to increase the resonance bandwidth (60–1200 rad/s) and output power (0.2 W). However, due to strong nonlinearity, an unstable region occurred near the main first resonance, which resulted from the Neimark–Sacker bifurcation.

Abstract Grape pomace is a by-product of the wine making industry with great availability and energetic potential. Torrefaction is a pre-treatment that may enhance the biomass quality as a fuel, and consists in exposing the biomass to an inert atmosphere at a temperature between 200 °C and 300 °C. This study evaluates the combustion characteristics of raw and torrefied grape pomace in a thermogravimetric analyzer and in a drop tube furnace. Initially, the raw grape pomace was torrefied in an argon inert atmosphere at 260 °C. Subsequently, the combustion of the raw and torrefied grape pomace was examined in the thermogravimetric analyzer through non-isothermal runs at a heating rate of 10 °C/min from room temperature to 800 °C. Finally, the combustion of both biomass residues was evaluated in the drop tube furnace at 1100 °C. The data reported includes gas temperature, major gas species concentration and particle burnout measured along the axis of the drop tube furnace. The main conclusions of this study are (i) for the devolatilization stage, the thermogravimetric data yielded apparent activation energy values of 84.9 and 85.2 kJ mol−1, and for the char oxidation stage of 137.5 and 109.2 kJ mol−1 for the raw and torrefied grape pomace, respectively; (ii) the NOx concentrations along the drop tube furnace were always higher for the combustion of the torrefied grape pomace than for the combustion of the raw grape pomace because the former residue has a higher nitrogen content; and (iii) the burnout values along the drop tube furnace were always lower for the combustion of the torrefied grape pomace than for the combustion of the raw grape pomace because the former residue has a lower volatile content and a higher fixed carbon content.

After a halt of four years, the n TOF spallation neutron facility at CERN has resumed operation in November 2008 with a new spallation target characterized by an improved safety and engineering design, resulting in a more robust overall performance and e cient cooling. The rst measurement during the 2009 run has aimed at the full characterization of the neutron beam. Several detectors, such as calibrated ssion chambers, the n TOF Silicon Monitor, a Mi- croMegas detector with 10B and 235U samples, as well as liquid and solid scintillators have been used in order to characterize the properties of the neutron uence. The spatial pro le of the beam has been studied with a specially designed \X-Y