• Energy Research
• engineering and technology close
• JP close
• TH close

AbstractHere, we present the results of evaluation of solar energy potential and photovoltaic (PV) module performance from actual data measured over a period of more than 2 years in the Gobi Desert of Mongolia. To allow estimation of solar energy potentials and durability of PV systems in the Gobi Desert area, a data acquisition system, including crystalline silicon (c‐Si), polycrystalline silicon (p‐Si) modules, and two sets of precision pyranometers, thermometers, and anemometer, was installed at Sainshand City in October 2002. This system measures 23 parameters, including solar irradiation and meteorological parameters, every 10 min. High output gain was observed due to operation at extremely low ambient temperatures and the module performance ratios (PRs) were high (>1·0) in winter. In summary, the present study showed that a PV module with a high temperature coefficient, such as crystalline silicon, is advantageous for use in the Gobi Desert area. Copyright © 2006 John Wiley & Sons, Ltd.

Interfacial resistance at electrode‐high Li+ conductive solid electrolytes must be reduced well to develop high‐power all‐solid‐state batteries using oxide‐based solid electrolytes (Ox‐SSBs). Herein, crystalline electrode films of LiCoO2 (LCO) are formed on a high Li+ conductive crystalline‐glass solid electrolyte sheet, Li1.3Al0.3Ti2(PO4)3 (LATP) (σ25 °C = 1 × 10−4 S cm−1), at room temperature by aerosol deposition (AD), and the effects of the annealing temperature on the interfacial resistivities (Rint) at the LCO/LATP are investigated. The Rint visibly increases by annealing over 500 °C with the growth of Co3O4 as a reactant. In contrast, Rint is reduced to ≈100 Ω cm2 by low‐temperature annealing at 250–350 °C due to superior contact through the structural rearrangement of an artificial metastable interface formed by the AD. These results are applied to bulk‐type Ox‐SSB, Li/Li7La3Zr2O12(LLZ)/LCO–LATP, and our best Ox‐SSB delivers a discharge capacity of 100 mA cm−2 at 100 °C.

上下方向に単調和振動をする水平面上におかれた非反発性物体の運動解析を振動加速度の大きい範囲に対してまず行なった。次に二れの延長として個々のものは反発性てある鍋球で形成された層の運動について検討した。この場合には, 衝撃を受けて鋼球群の充てん構造が変化する二とおよび反発によってランダムに運動をする層上部の鋼球群が下部層の運動を抑制するという働きによって, 層の大部分は規則正しい運動をすることが認められた。そこでこれに対する上下方向の運動方程式として非反発性物体の場合をも包含したかたちの式を提示し, 実教によりこれを確かめた。このよ5な検討結果は主として振動ミルによる粉砕現象を検討するさいの基礎として役立つものと思われる。

Abstract The anodic polarization behaviour of iron whisker crystals was investigated in a neutral solution with or without the presence of chloride ion, with special attention to the role played by surface defects in the dissolution, the passivation and the pitting of iron. The grown whisker used was substantially dislocation-free and the defect density was varied by twisting of whisker. With increase in the angle of twisting, the anodic dissolution current increased in a chloride-free solution, whereas it decreased in a chloride-containing solution. The defect density in the substrate had no remarkable effect on passivation but the thickness of the passive film was slightly increased on twisted whiskers. The anodic polarization curve of a grown whisker in a chloride-containing solution did not exhibit a distinct pitting potential. By twisting of whisker, however, a current rise due to pitting appeared on the polarization curve and the apparent pitting potential shifted in the negative direction with increasing angle of twisting. Potentiostatic polarization experiments in a chloride-containing solution showed the emergence of random current pulses due to the breakdown of passive film and to repassivation. It is highly probable that the breakdown of the passive film occurs at the physical or chemical inhomogeneities in the passive film not associated with dislocation termini but that pitting occurs only when the breakdown occurs at emergent dislocation sites.

In order to exploit renewable energies from tidal stream, tandem propellers of a unique counter-rotating type horizontal-axis tidal turbine was firstly designed based on the blade element momentum (BEM) theory. And then a multi-objective numerical optimization method coupled the response surface method (RSM) with the genetic algorithm (GA) was employed to obtain desirable blade profiles. The front blade pitch angle distribution was taken as optimization variable in this paper, as it plays an important role in affecting the inlet conditions of the rear blade. The numerical results show that both optimization objectives of power coefficient and thrust coefficient can be significantly improved. It was verified that the performance of the power unit with the optimized blades increases obviously by optimizing the pitch angle.

China’s research on and specific implementation of energy saving for buildings are mainly concentrated in urban areas, but according to 2016 statistics, the rural population accounts for 42.65% of the total population, so rural housing has considerable energy-saving potential. However, the degree of attention to the energy consumption of rural houses needs to be improved. Regarding the research on and implementation of passive energy-saving strategies for residences, compared with centralized urban high-rise residences, rural residences mainly have independent courtyards, with a flexible layout and easier transformation. In this study, a system that uses the common cold lanes in traditional villages and buildings’ exterior walls was constructed, and the indoor spaces of courtyard buildings in southern Shaanxi were completely passively cooled in summer. This system can be completely separated from the supply of artificial energy by relying on the accumulation and buoyancy effects of air in patios and cold lanes and the hot-pressure ventilation in buildings to cool the buildings and greatly improve indoor ventilation efficiency. As the building is ventilated and cooled, the air wall formed in the system can effectively prevent direct contact between the outdoor and indoor temperatures and reduce the impact of thermal wall radiation on the interior. In previous studies on the passive design of courtyard houses, scholars considered the effect of thermal wall radiation on indoor temperature in simulations. Therefore, in this study, we also separately calculated whether to consider the difference between the situation with and without wall heat radiation (WHR) when simulating thermal conversion. The final results show that when the cooling system was adopted, the annual cooling load of the whole building was 4786.494 kW·h without WHR. However, with WHR, the cooling load reduction was 2989.128 kW·h, a difference of 1797.336 kW·h.

This paper presents a multi-objective optimization model for a long-term generation mix in Indonesia. The objective of this work is to assess the economic, environment, and adequacy of local energy sources. The model includes two competing objective functions to seek the lowest cost of generation and the lowest CO2 emissions while considering technology diffusion. The scenarios include the use of fossil reserves with or without the constraints of the reserve to production ratio and exports. The results indicate that Indonesia should develop all renewable energy and requires imported coal and natural gas. If all fossil resources were upgraded to reserves, electricity demand in 2050 could be met by domestic energy sources. The maximum share of renewable energy that can be achieved in 2050 is 33% with and 80% without technology diffusion. The least cost optimization produces lower generation costs than the least CO2 emissions, as well as the combined scenario. Total CO2 emissions in 2050 are five to six times as large as current emissions. The least CO2 emissions scenario can reduce almost half of the CO2 emissions of the least cost scenario by 2050. The proposed multi-objective optimization model leads some optimal solutions for a more sustainable electricity system.

In order to study the effect of burst temperature on the coolant flow channel restriction, burst tests of fuel bundles were performed. Each bundle consisted of 49 rods (7×7 rods), and bursts were conducted in flowing steam. Burst temperature was changed by changing the internal gas pressure in rods. After the burst, the ballooning behavior of each rod and the degree of coolant flow area restriction in the bundle were measured. Maximum swelling of rod occurs when the burst temperature is around α and α+β phase boundary, and this phenomenon is almost the same as that in single rod burst tests. Maximum coolant flow area restriction is also observed in this condition.