• Energy Research
• Restricted close
• IT close
• RU close
• EC close
• UA close

Hydrogen generation from water using solar energy has grown into a promising approach for sustainable energy production. Over the last years, graphitic carbon nitrides (g-C3N4, CN), polymers based on the heptazine-group, have been widely applied as photocatalysts for H2 evolution. The poor charge separation efficiency of CN is considered the major drawback. Here, we investigated the effect of coupling CN with different types of carbon nanotubes on the charge transfer properties and the photocatalytic H2 evolution. We used carbon nanotubes (CNTs) of different wall number (single (SWCNTs), double (DWCNTs) and multi-walled (MWCNTs) CNTs) for the development of full-organic CN based composite photocatalysts. Photoactivity was drastically affected by the content but more importantly by the nature of the CNTs. The SWCNTs functionalized CN composites were the most active presenting approximately 2-5 times higher H2 evolution than the corresponding DWCNTs and MWCNTs functionalized CN under both solar and pure visible light irradiation. Photoactivity was primarily controlled by the improved electronic properties linked with the abundance and stability of photogenerated charges as evidenced by electron paramagnetic resonance spectroscopy. Transient absorption spectroscopy verified the transfer of reactive electrons from CN to CNTs. CNTs functioned as electron acceptors improving charge separation. The data suggest that charge transfer is inversely proportional to the wall number of the CNTs and that photoactivity is directly controlled by the size at the nanoscale of the CNTs used. In the CNTs/CN nanocomposites, photogenerated electrons are transferred more efficiently from CN when SWCNTs are used, providing more available electrons for H2 production.

This deliverable focuses on ASTEP’s informed consent procedures for research actions involving human participants, in regard to the collection, storage, and protection of personal data. The explicit confirmation that the data used in the project are publicly available and can be freely used for the purposes of the project is also given.

This is the longest continuous experiment where ethylenediurea (EDU) was used to protect plants from ozone (O3). Effects of long-term ambient O3 exposure (23 ppm h AOT40) on biomass of an O3 sensitive poplar clone (Oxford) were examined after six years from in-ground planting. Trees were irrigated with either water or 450 ppm EDU. Above (-51%) and below-ground biomass (-47%) was reduced by O3 although the effect was significant only for stem and coarse roots. Ambient O3 decreased diameter of the lower stem, and increased moisture content along the stem of not-protected plants (+16%). No other change in the physical wood structure was observed. A comparison with a previous assessment in the same experiment suggested that O3 effects on biomass partitioning to above-ground organs depend on the tree ontogenetic stage. The root/shoot ratios did not change, suggesting that previous short-term observations of reduced allocation to tree roots may be overestimated.

AbstractThe achievements of the last two decades in using solar energy for naturally ventilating and heating buildings of any size and scope across the world are remarkable, though comprising a niche market and being generally poorly known to this point. Air quality, thermal and hygrometric comfort, and reduced energy costs are some of the benefits provided by solar ventilated spaces. We identify the remaining hurdles to be addressed prior to forthcoming widespread adoption of this technology in the building environment across the world, well beyond the cold‐climate countries.

Ostrava in the Moravian-Silesian region (Czech Republic) is a European air pollution hot spot for airborne particulate matter (PM), polycyclic aromatic hydrocarbons (PAHs), and ultrafine particles (UFPs). Air pollution source apportionment is essential for implementation of successful abatement strategies. UFPs or nanoparticles of diameter <100 nm exhibit the highest deposition efficiency in human lungs. To permit apportionment of PM sources at the hot-spot including nanoparticles, Positive Matrix Factorization (PMF) was applied to highly time resolved particle number size distributions (NSD, 14 nm-10 μm) and PM0.09-1.15 chemical composition. Diurnal patterns, meteorological variables, gaseous pollutants, organic markers, and associations between the NSD factors and chemical composition factors were used to identify the pollution sources. The PMF on the NSD reveals two factors in the ultrafine size range: industrial UFPs (28%, number mode diameter - NMD 45 nm), industrial/fresh road traffic nanoparticles (26%, NMD 26 nm); three factors in the accumulation size range: urban background (24%, NMD 93 nm), coal burning (14%, volume mode diameter - VMD 0.5 μm), regional pollution (3%, VMD 0.8 μm) and one factor in the coarse size range: industrial coarse particles/road dust (2%, VMD 5 μm). The PMF analysis of PM0.09-1.15 revealed four factors: SIA/CC/BB (52%), road dust (18%), sinter/steel (16%), iron production (16%). The factors in the ultrafine size range resolved with NSD have a positive correlation with sinter/steel production and iron production factors resolved with chemical composition. Coal combustion factor resolved with NSD has moderate correlation with SIA/CC/BB factor. The organic markers homohopanes correlate with coal combustion and the levoglucosan correlates with urban background. The PMF applications to NSD and chemical composition datasets are complementary. PAHs in PM1 were found to be associated with coal combustion factor.

The incorporation of recycled materials in concrete as a partial replacement of cement is becoming an alternative strategy for decreasing energy-intensive and CO2 emissions imputable to the cement manufacture, while investigating new potential uses of such multifunctional materials for environmental sustainability opportunities. Therefore, low-cost and worldwide availability of by-products materials is being assessed for sensible heat thermal energy storage applications based on cementitious materials. A greater concern is especially required focusing on the thermal stability of cement paste under high temperature cycled conditions. Moreover, compatibility between cement type and supplementary cementitious materials is determinant for the proper performance reliability. In this study, benchmark cement types were selected, i.e., ordinary Portland and calcium aluminate. Six supplementary cementitious materials were added to both types of cement in a content of 10 % and 25 %. Thermo-mechanical properties were studied before and after 10 thermal cycles from 290 to 650 ◦C. Results after thermal cycling showed that calcium aluminate cement paste mixtures maintained their integrity. However, most ordinary Portland cement paste mixtures were deteriorated: only mixtures with 25 % cement replacement with chamotte, flay ash, and ground granulated blast furnace slag remained without cracks. Calcium aluminate cement paste mixtures obtained the highest compressive strength, for partial replacement of cement with 10 % of chamotte, ground granulated blast furnace slag, and iron silicate. The incorporation of supplementary cementitious materials did not increase the thermal conductivity. This work was partially funded by the Ministerio de Ciencia, Innovación y Universidades de España (RTI2018-093849-B-C31 - MCIU/AEI/FEDER, UE) and by the Ministerio de Ciencia, Innovación y Universidades - Agencia Estatal de Investigación (AEI) (RED2018-102431-T). The authors at University of Lleida would like to thank the Catalan Government for the quality accreditation given to their research group (2017 SGR 1537). GREiA is certified agent TECNIO in the category of technology developers from the Government of Catalonia. This work is partially supported by ICREA under the ICREA Academia programme and by the Italian project ‘SOS-CITTA’ supported by Fondazione Cassa di Risparmio di Perugia under grant agreement No 2018.0499.026. Laura Boquera acknowledgments are due to the PhD school in Energy and Sustainable Development from University of Perugia. Laura Boquera would like to acknowledge the financial support provided by UNIPG – CIRIAF InpathTES project. The authors also thank the companies that provided the material to make possible this experimental research: Arciresa, Abrasivos Mendiola EDERSA—Masaveu Industria, General Admixtures S.p.A, Mapei, Ciments Molins industrial, and Promsa for the material supplied in this research. Financial support of the UNIPG-CIRIAF team has been achieved from the Italian Ministry of University and Research (MUR) in the framework of the Project FISR 2019: “Eco Earth” (code 00245) and it is gratefully acknowledged.

The large use of portable devices imposes a new interest in the development of power backup systems with constraints in terms of compactness and safety. Such systems have to match the use as battery backups as well as a self-standing operating. Thermoelectric generators (TEGs) allow access to new ways of power supply thanks to their long lifetimes, their competitive efficiencies at low powers and their capability of providing multiple outputs. In this work, a TEG based on catalytic combustor has been proposed aiming to approach electrical output and dimension of the commonly used AA batteries. Catalytic combustion provides the possibility to profit from the high power densities of hydrocarbon in limited space and low burning temperatures meeting the needs of the TEGs as a heat engine. The system has been characterized for different fuel flow rates. The measured TEG efficiency is 3.4% with the electrical power output of 5.3 W. The system thermal behavior has been experimentally investigated according to literature models, by evaluating the effectiveness of the design and of the chosen practical solutions. The system produced reached the electrical output target, matching the characteristics proper of most of the common commercial AA batteries in a similar device volume.

In themediumtolongterm,lowfossilfuelavailabilitywillmakeitnecessarytofindalternatives.Mass productionofbiofuelswillnotbeapracticalsolutionbecauseitrequiresstrongcompetitionforland that isusedforgrowingfood.Therefore,itwillbenecessarytorevisetheframeoftransportation energy sources.Thenumberofpurelight-andheavy-dutyelectricvehiclescouldincreaseinurban areas.Instead,itwillbehardtofindaviablealternativetotheinternalcombustionengineforextra- urban transportvehicles,thereforealternativesyntheticfuelscouldbeusedtocompensateforfossil fuel depletion.Asidefromasmallshareobtainablefrombiomass,mostsyntheticfuelsareexpectedto be obtainedfromcoal.Amongthese,syntheticnaturalgasrepresentsaverygoodsolution.Infact, syntheticnaturalgaswillbeadvantageouswithrespecttohydrogen,whoseon-boardstoragewillbean unsolvedprobleminthemediumterm,andwithrespecttosyntheticliquidfuels,whichrequiremore energy intheproductionphase.Moreover,thecarboncontentofliquidfuels,whichishigherthanthat of gaseousfuels,willberesponsibleforhigherCO2 emissionsfromvehicles.Currently,naturalgashas poor diffusioninthetransportsector,andthispaperhighlightsthemotivationsforfavouringapolicy aimedatincreasingtheshareofgaseousfuel-poweredvehicles.Inadditiontothelowenvironmental impact,syntheticnaturalgasalsooffersthepossibilityofoptimisingtheutilisationoffutureresources