• Energy Research
• 2021-2025close
• IN close
• US close
• AU close
• Solar Energy close

Abstract Cu2BaSn(S,Se)4 (CBTSSe) solar cells are emerging photovoltaic devices due to their high theoretical efficiencies of ~31%, environment-friendly and earth-abundant composition, low density of non-recombination defects, and so on. However, the record efficiency of CBTSSe solar cell is only 5.2%, showing the importance of studying their performance via numerical analysis to further enhance their practical efficiencies. In this paper, the effect of absorber and buffer layers on performances of Cu2BaSnS4 (CBTS) solar cells are firstly systematically studied via the SCAPS-1D software to provide a platform for the study of the effect of MoS2 interlayer on the performances of CBTS solar cells. The highest PCE of CBTS solar cell with a 30 nm CdS buffer layer is 11.87%. The PCE of CBTS solar cell with a 0.8 μm CBTS absorb layer is 12.51%, indicating that the CBTS solar cell is a potential low-cost solar cell due to its large optical absorption coefficient (α > 104 cm−1). The efficiency of CBTS solar cell is improved to 16.47% when the carrier concentration of CBTS is 1016 cm−3. The relationship between the performance of solar cell and the band gap, thickness, donor concentration, acceptor concentration of MoS2 interlayer is systematically investigated on the basis of the optimized efficiency. It is found that MoS2 interlayer plays an important role in the performance of CBTS solar cell. The p-type MoS2 has a beneficial effect on the efficiency improvement while the n-type MoS2 has a negative effect on the efficiency enhancement. The highest PCE of CBTS solar cell is as high as 18.28% when the thickness and the acceptor concentration of MoS2 are 4 nm and 1019 cm−3, respectively. Our simulation result provides a promising research direction to further improve the actual efficiency of the CBTS solar cell.

Abstract In this paper, the experimental performance of a 45 m2 solar field of non-tracking external compound parabolic (XCPC) collectors installed at the University of California, Merced is described. The solar field was operated during July-August 2020 in both clean and dirty conditions and at varying operating temperatures (70, 135, 170 °C) while operating an air heater, thermal evaporator, and double effect absorption chiller. Performance data was used to develop an instantaneous solar field performance model which was then incorporated into an annual performance model using TMY3 data to estimate yearly production from the solar field. The model predicts an annual generation of ∼1100 kWh/m2-year at 80 °C, ∼1000 kWh/m2-year at 100 °C, ∼900 kWh/m2-year at 120 °C, ∼800 kWh/m2-year at 140 °C, and ∼700 kWh/m2-year at 160 °C in California. The XCPC technology is currently expected to have an installed cost of $300/m2 and an annual operations and maintenance cost of $6.5/m2-year. Over a 25 year lifetime it provides a levelized cost of heat at 2–4 cents per kWhth delivered. This is below the cost of commercial natural gas in California and at temperatures ≤ 120 °C below the cost of industrial natural gas, which highlights the potential of the XCPC technology for decarbonizing thermal applications such as water and space heating, drying, sterilization, desalination, evaporation, low pressure steam, double effect absorption chilling, process heating, and more. The lifetime cost of emissions reductions is ∼$169 per metric ton of avoided CO2 when replacing natural gas, ∼$137/MT CO2 when replacing propane, and ∼$83/MT CO2 when replacing electric heating.

Abstract In this article, we have studied an identical section of a core-shell ZnO Nanorod (NR) based lead-free perovskite solar cell. Various factors affecting the solar cell’s performance have been rigorously investigated for device optimization; specifically, the length and diameter of the ZnO NR core, perovskite shell thickness, thickness of perovskite cap layer, and hole transport layer (HTL) thickness. The defect density of states (DOS) in the perovskite absorber layer and the effect of interface defect density on the performance of the cell are also studied. We obtained power conversion efficiency (PCE) of 14.50%, the open-circuit voltage (VOC) of 0.96 V; short-circuit current density (JSC) of 18.11 mA/cm2 and Fill factor (FF) of 83.35%. We also analyzed the effect of tilt or inclination of NR on the performance of the cell which is a crucial factor toward achieving high performance. By optimizing the device parameters, we have achieved a PCE of 21.27%, VOC of 0.97 V, JSC of 29.56 mA/cm2, and FF of 84.15% at an inclination of 10-degree tilt with respect to the incident light under AM 1.5 illumination. The shadowing mechanism behind efficiency droop is also presented to further realize an optimal design high-performance PSC.

Abstract This study evaluates the mechanical behaviour of a ceramic disk which makes up an innovative volumetric absorber design. The new receiver design is formed by a group of disks which are rotating inside a cavity, distributing the radiation absorbed in the aperture to the whole cavity. This research studies the stress fields due to thermal gradients and its effect in the crack propagation in the disks. The complete analysis has been carried out in three steps: the mechanical characterization of the material, in order to know its fracture properties, the computational fluid dynamics (CFD) analysis of the disk, in order to know the temperature distribution in the disk and the finite element model (FEM), which uses as inputs the results of the two previous steps and solves the stress fields in the disk and the fracture behaviour. Fracture and crack growing in the disk have been modelled by using a cohesive element, which, from the fracture properties of the material, allows simulating the crack growing in the disk. This investigation, by means of stress fields and crack propagation analysis, demonstrates the mechanical viability of the disks concept.